English dropdown-ico

Manual Whirlpool 8527795

26 pages 0.79 mb
Download

Go to site of 26

Summary
  • Whirlpool 8527795 - page 1

    Installation Inst ructions IMPOR T ANT : Read and save these instructions IMPORTANT Installer: Leave Installation Instructions with the owner. Owner: Keep Installation Instructions for future reference. Save Installation Instructions for local electrical inspector’s use. COMMERCIAL DR YER GAS Part No. 8527795 COMMERCIAL LAUNDRY PRODUCTS ® www.wh ...

  • Whirlpool 8527795 - page 2

    Page 2 Post this warning in a prominent location. It is recommended that the operator post, in a prominent location, instructions for the customer's use in the event the customer smells gas. This information should be obtained from your local gas supplier. Before you start... We have provided many important safety message in this manual and on ...

  • Whirlpool 8527795 - page 3

    MAXIMUM LENGTH OF 4-INCH (10.2 cm) DIAMETER RIGID METAL VENT No. of 90° turns EXHAUST HOOD TYPE 2-1/2" (6.4 cm) 4" (10.2 cm) 4" (10.2 cm) 4" (10.2 cm) 4" (10.2 cm) 4" (10.2 cm) 64 FT. (19.5 m) 54 FT. (16.5 m) 44 FT. (13.4 m) 35 FT. (10.7 m) 27 FT. (8.2 m) 64 FT. (19.5 m) 54 FT. (16.5 m) 44 FT. (13.4 m) 35 FT. (10.7 m) ...

  • Whirlpool 8527795 - page 4

    exhaust hood or sweep elbow 180° sweep elbow wall wall roof main exhaust vent horizontal vent 2 ft. (61 cm) min. above vertical vent highest point of building main collector vent Do Not install screening or cap over end of vent. Gas requirements OBSERVE ALL GOVERNING CODES AND ORDINANCES. Page 4 An exhaust hood should cap the outside end of the ma ...

  • Whirlpool 8527795 - page 5

    Page 5 to dryer shutoff valve “open” position gas supply line H. If local codes and ordinances permit, it is recommended that new flexible metal tubing, design-certified by the AGA or CSA, be used for connecting the dryer to the gas supply line. (The gas feed pipe which extends through the lower rear of the dryer is provided with 3/8-inch metal ...

  • Whirlpool 8527795 - page 6

    6. Move dryer close to final position. Remove cardboard or hardboard from under dryer. 8. Connect gas supply to dryer. Use pipe-joint compound resistant to the action of L.P. gas for gas connections. If flexible metal tubing is used, be certain there are no kinks. If necessary for service, open the toe panel, use a putty knife to press on the toe p ...

  • Whirlpool 8527795 - page 7

    Page 7 6. Move dryer close to final position. Remove cardboard or hardboard from under dryer. 5. Remove the service door of the meter case. Lift the service door up at the back and remove. Install money- accepting device. (Refer to manufaturer's instructions for proper installation.) For dryers using coin slides, use adapter kit supplied with ...

  • Whirlpool 8527795 - page 8

    Page 8 3. Assemble 3/4" U.L.-listed strain relief (U.L. marking on strain relief) into the hole below terminal block opening. Tighten strain relief screws just enough to hold the two clamp sections together. Install power supply cord/cable through the strain relief. For a grounded, cord-connected appliance — GROUNDING INSTRUCTIONS: This appl ...

  • Whirlpool 8527795 - page 9

    Page 9 Four -wire connection... Four-wire power supply cord must have four, No.-10 copper wires and match a four-wire receptacle of NEMA Type 14-30R. The fourth wire (ground conductor) must be identified with a green cover and the neutral conductor by a white cover. NEUTRAL NEUTRAL (white) 3/4" U.L.-listed strain relief ground prong ground wir ...

  • Whirlpool 8527795 - page 10

    Three-wire connection... Three-wire power supply cord must have three, No.-10 copper wires and match a three-wire receptacle of NEMA Type 10-30R. 4. Loosen or remove center terminal block screw. 6. Connect the other wires to outer terminal block screws. Tighten screws. 7. Tighten strain relief screws. 8. Insert tab of terminal block cover into slot ...

  • Whirlpool 8527795 - page 11

    Three-wire connection... Three-wire r eceptacle 6. Connect the other wires to outer terminal block screws. Tighten screws. 7. Tighten strain relief screws. 8. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 5. Remove the appliance harness ground wire (green with yellow stripes) from the external ...

  • Whirlpool 8527795 - page 12

    0" (0 cm)* Recessed area and closet installation instructions If dryer does not operate properly ... If you need assistance... Moving the dryer to a new location... Check the following to be sure that: 1. Electric supply is connected. 2. Circuit breakers are not tripped or house fuses blown. 3. Door is closed. 4. Controls are set in a running ...

  • Whirlpool 8527795 - page 13

    Product dimensions 29" (73.7 cm) dryer 27" (68.6 cm) dryer 29" (73.7 cm) Part No. 8527795 © 2001 Whirlpool Corporation Prepared by Whirlpool Corporation, Benton Harbor, Michigan 49022 Printed in U.S.A. 27-1/4" (69.2 cm) 16" (40.6 cm) ELECTRIC GAS EXHAUST 4-3/4" (12.1 cm) 13" (33 cm) 1-1/4" (3.2 cm) BACK VIEW ...

  • Whirlpool 8527795 - page 14

    Inst ructions d’installation IMPOR T ANT : Lire et conserver ces instructions. IMPORTANT Installateur : Remettre les instructions d’installation au propriétaire. Propriétaire : Conserver les instructions d’installation pour consultation ultérieure. Conserver les instructions d’installation pour consultation par l’inspecteur local des i ...

  • Whirlpool 8527795 - page 15

    Page 2 Afficher cet avertissement en un endroit très visible. On recommande que l’utilisateur affiche en un lieu très visible les instructions décrivant ce que le client doit faire si une odeur de gaz est perceptible. Obtenir cette information auprès du fournisseur de gaz local. A vant de commencer ... Nous donnons de nombreux messages de sé ...

  • Whirlpool 8527795 - page 16

    Nbre de coudes À 90° TYPE DE BOUCHE DE DÉCHARGE 6,4 cm (2-1/2 po) 10,2 cm (4 po) 10,2 cm (4 po) 10,2 cm (4 po) 10,2 cm (4 po) 10,2 cm (4 po) 19,5 m (64 pi) 16,5 m (54 pi) 13,4 m (44 pi) 10,7 m (35 pi) 8,2 m (27 pi) 19,5 m (64 pi) 16,5 m (54 pi) 13,4 m (44 pi) 10,7 m (35 pi) 8,2 m (27 pi) 17,7 m (58 pi) 14,6 m (48 pi) 11,6 m (38 pi) 8,8 m (29 pi) ...

  • Whirlpool 8527795 - page 17

    bouche de décharge ou conduit horizontal coude de déviation à 180° mur mur toit conduit d’évacuation collectif coude de déviation 61 cm (2 pi) min. au-dessus du point le plus élevé du bâtiment conduit vertical Ne pas installer une grille ou un couvercle sur l’extrémité du conduit d’évacuation. Spécifications Page 4 L’extrémit? ...

  • Whirlpool 8527795 - page 18

    Page 5 vers la sécheuse robinet d’arrêt - position d’ouverture H. Si les codes et règlements locaux le permettent, on recommande l’emploi d’un conduit métallique flexible neuf de conception homologuée par l’American Gas Association ou CSA pour le raccordement de la sécheuse à la canalisation d’arrivée de gaz. (Le raccord qui dé ...

  • Whirlpool 8527795 - page 19

    Commencer ... Page 6 prise de courant à 3 alvéoles canalisation d’arrivée de gaz robinet d’arrêt (gaz) conduit de décharge Avec la sécheuse dans la buanderie. 1. Enlever le ruban adhésif dans les angles avant de la sécheuse. Ouvrir la sécheuse; enlever les brochures et sachets de pièces. Essuyer parfaitement la surface interne du tamb ...

  • Whirlpool 8527795 - page 20

    Page 7 Commencer ... 1. Enlever le ruban adhésif dans les angles avant de la sécheuse. Ouvrir la sécheuse; enlever les brochures et sachets de pièces. Essuyer parfaitement la surface interne du tambour avec un chiffon humide. 2. Prendre deux cornières de carton de l’emballage et les placer sur le plancher à l’arrière de la sécheuse. Sai ...

  • Whirlpool 8527795 - page 21

    Page 8 3. Installer un serre-câble de 3/4 po (agrément UL, avec marque sur le serre-câble) dans le trou au-dessous de l’ouverture du bloc de connexion. Serrer les vis du serre-câble juste assez pour que les deux parties du serre-câble soient maintenues ensemble. Faire passer le câble d’alimentation entre les deux plaquettes. Exécuter les ...

  • Whirlpool 8527795 - page 22

    Page 9 Circuit à quatre conducteurs… Le cordon d’alimentation à quatre conducteurs doit comporter quatre conducteurs de cuivre no 10, et on doit disposer d’une prise de courant à quatre alvéoles à type NEMA 14-30R. Le quatrième conducteur (liaison à la terre) doit être identifié par un isolant vert et le conducteur neutre par un isol ...

  • Whirlpool 8527795 - page 23

    Circuit à trois conducteurs… Le cordon d’alimentation à trois conducteurs doit comporter trois conducteurs de cuivre no 10, et on doit disposer d’une prise de courant à trois alvéoles de type NEMA 10-30R. 4. Desserrer ou enlever la vis de la borne centrale du bloc de connexion. 5. Connecter le conducteur neutre (blanc ou central) du cordo ...

  • Whirlpool 8527795 - page 24

    Circuit à trois conducteurs… Prise de courant à trois conducteurs 4. Ôter la vis de la borne centrale du bloc. 5. Séparer le conducteur de liaison à la terre de l’appareil (vert avec rayure jaune) de la vis de connexion au châssis. Connecter le conducteur de liaison à la terre et le conducteur neutre (blanc ou central) à la borne centra ...

  • Whirlpool 8527795 - page 25

    0 cm (0 po)* Instructions pour l’installation dans un placard ou un encastrement Si la sécheuse ne fonctionne pas correctement... Si vous avez besoin d’aide... Déménagement de la sécheuse... Contrôler pour vérifier que : 1. Le circuit d’alimentation électrique est bien alimenté. 2. Les disjoncteurs ne sont pas ouverts et les fusibles ...

  • Whirlpool 8527795 - page 26

    Dimensions du produit Pièce n° 8527795 © 2001 Whirlpool Corporation Préparé par Whirlpool Corporation, Benton Harbor, Michigan 49022 Imprimé aux É.-U. Sécheuse 73,7 cm (29 po) Sécheuse 68,6 cm (27 po) 73,7 cm (29 po) 69,2 cm (27 1/4 po) 40,6 cm (16 po) 12,1 cm (4 3/4 po) 33 cm (13 po) 3,2 cm (1 1/4 po) VUE ARRIÈRE 46,7 cm (18 3/8 po) 10,2 ...

Manufacturer Whirlpool Category Clothes Dryer

Documents that we receive from a manufacturer of a Whirlpool 8527795 can be divided into several groups. They are, among others:
- Whirlpool technical drawings
- 8527795 manuals
- Whirlpool product data sheets
- information booklets
- or energy labels Whirlpool 8527795
All of them are important, but the most important information from the point of view of use of the device are in the user manual Whirlpool 8527795.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Whirlpool 8527795, service manual, brief instructions and user manuals Whirlpool 8527795. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Whirlpool 8527795.

Similar manuals

A complete manual for the device Whirlpool 8527795, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Whirlpool 8527795 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Whirlpool 8527795.

A complete Whirlpool manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Whirlpool 8527795 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Whirlpool 8527795, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Whirlpool 8527795, that we can find in the current document
3. Tips how to use the basic functions of the device Whirlpool 8527795 - which should help us in our first steps of using Whirlpool 8527795
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Whirlpool 8527795
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Whirlpool 8527795 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Whirlpool 8527795?

Use the form below

If you did not solve your problem by using a manual Whirlpool 8527795, ask a question using the form below. If a user had a similar problem with Whirlpool 8527795 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)