English dropdown-ico

Manual Dell E6400

99 pages 3.13 mb
Download

Go to site of 99

Summary
  • Dell E6400 - page 1

    Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Notes, Notices, and Cautions IfyoupurchasedaDELL™nSeriescomputer,anyreferencesinthisdocumenttoMicrosoft ® Windows ® operating systems are not applicable. Information in this docu ...

  • Dell E6400 - page 2

    Back to Contents Page  1394 Card Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the 1394 Card  Replacing the 1394 Card  Removing the 1394 Card   1. Follow the instructions in Before Working on Your Computer .  2. Remove the bottom of the ...

  • Dell E6400 - page 3

     Replacing the 1394 Card   1. Insert the 1394 card at a 45 - degree angle to fit the connector into the base assembly. Use the alignment pins to seat into position.  2. Replace the two M2 x 3 screws.  3. Route and connect the 1394 cable to the system board.  4. Replace the card cage (see Replacing the Card Cage ).  5. Replace t ...

  • Dell E6400 - page 4

    Back to Contents Page  Base Assembly Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the Bottom of the Base Assembly  Replacing the Bottom of the Base Assembly  Removing the Base Assembly  Replacing the Base Assembly   Removing the B ...

  • Dell E6400 - page 5

     5. Remove the hinge covers (see Removing the Hinge Covers ).  6. Remove the card from the WPAN/UWB/FCM card slot, if present (see Removing a WPAN (UWB/BT) Card or Removing an FCM from the WPAN/UWB/FCM Slot ).  7. Remove the heatsink assembly (see Removing the Processor Heatsink Assembly ).  8. Remove the hard drive (see Removing the Ha ...

  • Dell E6400 - page 6

     16. Replace the hinge covers (see Replacing the Hinge Covers ).  17. Replace the card from the WLAN/WiMax card slot, if applicable (see Replacing the WLAN/WiMax Card ).  18. Replace the card from the WWAN/FCM card slot, if applicable (see Replacing a WWAN Card or Replacing an FCM ).  19. Replace the bottom of the base assembly (see Rep ...

  • Dell E6400 - page 7

    Back to Contents Page  Battery Latch Assembly Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing a Battery Latch Assembly  Replacing the Battery Latch Assembly There are two battery latches, a left and a right, and each latch uses a unique latch assembly ...

  • Dell E6400 - page 8

     Replacing the Battery Latch Assembly   1. Place the spring on the alignment bracket.  2. Place the battery release button underneath the base assembly. For the right battery latch assembly, slide the alignment bracket to the left to align the button with the hole in the alignment bracket. For the left battery latch assembly, slide the ...

  • Dell E6400 - page 9

    17. Replace the hard drive (see Replacing the Hard Drive ).  18. Replace the bottom of the base assembly (see Replacing the Bottom of the Base Assembly ).  19. Follow the procedures in After Working on Your Computer . Back to Contents Page  ...

  • Dell E6400 - page 10

    Back to Contents Page  Working on Your Computer Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Recommended Tools  Before Working on Your Computer  After Working on Your Computer This document provides procedures for removing and installing the component ...

  • Dell E6400 - page 11

     7. Slide the battery out of the battery bay.  8. Disconnect any external devices and remove any installed cards before working on your computer: l  To remove any installed cards, such as an ExpressCard, see the Dell™TechnologyGuide on your computer or at support.dell.com . l  To undock from a docking station, see the E- Port Us ...

  • Dell E6400 - page 12

     4. Replace the battery. Slide the battery into the battery bay until it clicks into place.  5. Connect your computer and all attached devices to their electrical outlets.  6. Turn on your computer. Back to Contents Page  ...

  • Dell E6400 - page 13

    Back to Contents Page  Flashing the BIOS Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Flashing the BIOS From a CD  Flashing the BIOS From the Hard Drive If a BIOS - update program CD is provided with a new system board, flash the BIOS from the CD. If you do ...

  • Dell E6400 - page 14

    ...

  • Dell E6400 - page 15

    Back to Contents Page  Card Cage Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the Card Cage  Replacing the Card Cage  Removing the Card Cage   1. Follow the procedures in Before Working on Your Computer .  2. Remove the bottom of the ba ...

  • Dell E6400 - page 16

      1. Holding the card cage at a 45 - degree angle, attach the front of the card cage to the base assembly, then lower the card cage into place.  2. Replace the two M2 x 3 screws.  3. Replace the palm rest assembly ( Replacing the Palm Rest Assembly ).  4. Replace the right speaker grill (see Replacing the Right Speaker Grill/Fingerpr ...

  • Dell E6400 - page 17

    Back to Contents Page  Coin - Cell Battery Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the Coin - Cell Battery  Replacing the Coin - Cell Battery  Removing the Coin - Cell Battery   1. Follow the procedures in Before Working on Your Compu ...

  • Dell E6400 - page 18

     3. Replace the bottom of the base assembly (see Replacing the Bottom of the Base Assembly ).  4. Follow the procedures in After Working on Your Computer . Back to Contents Page  1 coin - cell battery 2 coin - cell battery cable ...

  • Dell E6400 - page 19

    Back to Contents Page  Processor Module Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the Processor Module  Replacing the Processor Module  Removing the Processor Module   1. Follow the instructions in Before Working on Your Computer .  ...

  • Dell E6400 - page 20

     5. Lift the processor module from the ZIF socket.  Replacing the Processor Module   1. Align the pin - 1 corner of the processor module with the pin - 1 corner of the ZIF socket, then insert the processor module. When the processor module is properly seated, all four corners are aligned at the same height. If one or more corners of the ...

  • Dell E6400 - page 21

    Back to Contents Page  Processor Heatsink Assembly Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the Processor Heatsink Assembly  Replacing the Processor Heatsink Assembly  Removing the Processor Heatsink Assembly   1. Follow the instructio ...

  • Dell E6400 - page 22

     6. Follow the procedures in After Working on Your Computer . Back to Contents Page  ...

  • Dell E6400 - page 23

    Back to Contents Page  I/O Card Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the I/O Card  Replacing the I/O Card  Removing the I/O Card   1. Follow the procedures in Before Working on Your Computer .  2. Remove the bottom of the base a ...

  • Dell E6400 - page 24

     Replacing the I/O Card   1. Place the I/O card in the base assembly.  2. Replace the M2 x 3 - mm screw to secure the I/O card to the base assembly.  3. Replace the plastic plug.  4. Replace the RJ - 11 modem connector (see Replacing the RJ - 11 Modem Connector ).  5. Replace the modem (see Replacing the Modem ).  6. Replace ...

  • Dell E6400 - page 25

    Back to Contents Page  ...

  • Dell E6400 - page 26

    Back to Contents Page  Display Assembly Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the Display Assembly (E6400 and M2400)   1. Follow the instructions in Before Working on Your Computer .  2. Remove the bottom of the base assembly (see Removing t ...

  • Dell E6400 - page 27

     Replacing the Display Assembly (E6400 and M2400)   1. Position the cables on the display assembly away from the base assembly.  2. Align the display hinges with the holes in the base of the computer, and lower the display into place.  3. Close the display and turn the computer upside down.  4. Route the display cable and wireless ...

  • Dell E6400 - page 28

     4. Disconnect and unroute the display cable, touch screen cable, and the wireless cables (WLAN, WWAN, and WPAN). Position all cables to the rear of the laptop after unrouting.  5. Remove the two M2.5 x 5 - mm screws from the hinges.  6. Turn the computer topside up.  7. Open the display to 90 degrees and lift the display assembly off t ...

  • Dell E6400 - page 29

    channel, including the tabs on the back of the base assembly.  5. Depending on the cards in your computer configuration, connect the antenna cables to their respective card: For WWAN, see Replacing a WWAN Card . For WPAN, see Replacing a WPAN (UWB/BT) Card . For WLAN, see Replacing the WLAN/WiMax Card . Place any unused antenna cables in the bas ...

  • Dell E6400 - page 30

     11. Once all snaps are released, lift the bezel from the display assembly.  Replacing the Display Bezel (E6400 and M2400)   1. Align the latch hook on the display panel with the small rectangular opening on the display bezel.  2. Simultaneously push in on the right and left sides of the bezel to engage the side bezel snaps. 1 right ...

  • Dell E6400 - page 31

     3. Simultaneously pull out on the top and bottom of the bezel to engage the top and bottom bezel snaps.  4. Gently snap the bezel into place to secure it to the display assembly.  5. Replace the display assembly (see Replacing the Display Assembly (E6400 and M2400) ).  6. Replace the hinge covers (see Replacing the Hinge Covers ).  ...

  • Dell E6400 - page 32

     Replacing the Display Bezel (E6400 ATG)   1. Align the latch hook on the display panel with the small rectangular opening on the display bezel.  2. Simultaneously push in on the right and left sides of the bezel to engage the side bezel snaps.  3. Simultaneously pull out on the top and bottom of the bezel to engage the top and botto ...

  • Dell E6400 - page 33

     2. Remove the bottom of the base assembly (see Removing the Bottom of the Base Assembly ).  3. Remove the hinge covers (see Removing the Hinge Covers ).  4. Remove the display assembly (see Removing the Display Assembly (E6400 and M2400) ).  5. Remove the display bezel (see Removing the Display Bezel (E6400 and M2400) ).  6. Remove ...

  • Dell E6400 - page 34

     Replacing the CCFL Display Panel and Brackets (E6400 and M2400)   1. Replace the four M2 x 3 - mm screws on the right bracket and the four M2 x 3 - mm screws on the left bracket.  2. Place the display panel upside down on your workspace in front of the display cover.  3. Connect the backlight cable to the inverter.  4. Connect th ...

  • Dell E6400 - page 35

    6. Remove the four M2.5 x 5 - mm screws from the display panel.  7. Lift the display panel out of the display cover and carefully lay the display panel flat on your workspace. Be careful to avoid damaging the display panel with the hinges and cables on the display cover.  8. Use the pull tab to disconnect the display cable.  9. Remove two ...

  • Dell E6400 - page 36

     1. Replace the two M2 x 3 - mm screws on the right bracket and the two M2 x 3 - mm screws on the left bracket.  2. Connect the display cable to the connector on the back of the display panel.  3. Route the display cable around the notch on the display cover and set the display panel in place.  4. Replace the four M2.5 x 5 - mm screws t ...

  • Dell E6400 - page 37

     9. For touch screen display panels, disconnect the touch screen cable.  10. Remove four M2 x 3 - mm screws from the right bracket and four M2 x 3 - mm screws from the left bracket.  Replacing the Display Panel and Brackets (E6400 ATG)   1. Replace the four M2 x 3 - mm screws on the right display panel bracket and the four M2 x 3 - m ...

  • Dell E6400 - page 38

     8. Replace the display assembly (see Replacing the Display Assembly (E6400 ATG) ).  9. Replace the hinge covers (see Replacing the Hinge Covers ).  10. Replace the bottom of the base assembly (see Replacing the Bottom of the Base Assembly ).  11. Follow the procedures in After Working on Your Computer .  Removing the Display Inverte ...

  • Dell E6400 - page 39

     5. Replace the hinge covers (see Replacing the Hinge Covers ).  6. Replace the bottom of the base assembly (see Replacing the Bottom of the Base Assembly ).  7. Follow the procedures in After Working on Your Computer .  Removing the Display Hinges (E6400 and M2400)   1. Follow the instructions in Working on Your Computer .  2. ...

  • Dell E6400 - page 40

    3. Replace the display panel (see Replacing the CCFL Display Panel and Brackets (E6400 and M2400) or Replacing the LED Display Panel and Brackets (E6400 and M2400) ).  4. Replace the display bezel (see Replacing the Display Bezel (E6400 and M2400) ).  5. Replace the display assembly (see Replacing the Display Assembly (E6400 and M2400) ).  ...

  • Dell E6400 - page 41

     2. Replace the two M2.5 x 5 - mmscrewsontherighthingeandthetwoM2.5x5 - mm screws on the left hinge.  3. Replace the display panel (see Replacing the Display Panel and Brackets (E6400 ATG) ).  4. Replace the display bezel (see Replacing the Display Bezel (E6400 ATG) ).  5. Replace the display assembly (s ...

  • Dell E6400 - page 42

     4. Tighten the M2 x 3 - mm screw that secures the microphone board to the display cover.  5. Replace the display bezel (see Replacing the Display Bezel (E6400 and M2400) or Replacing the Display Bezel (E6400 ATG) ).  6. Replace the display assembly (see Replacing the Display Assembly (E6400 and M2400) or Replacing the Display Bezel (E6400 ...

  • Dell E6400 - page 43

     Replacing the Camera and Microphone Assembly   1. Slide the cable connector of the camera/microphone cable into the connector on the camera/microphone assembly.  2. Close the lever on the connector on the camera/microphone assembly.  3. Angle in and align the camera/microphone assembly with the notch on the display cover.  4. Tig ...

  • Dell E6400 - page 44

     Replacing the Latch Hook Assembly   1. Angle the latch hook into the display cover.  2. Replace the M2.5 x 5 - mm screw that secures the latch hook assembly to the display cover.  3. Replace the display bezel (see Replacing the Display Bezel (E6400 and M2400) or Replacing the Display Bezel (E6400 ATG) ).  4. Replace the display a ...

  • Dell E6400 - page 45

      1. Remove the tape from the cables that are taped to the display cover.  2. Replace the display panel (see Replacing the CCFL Display Panel and Brackets (E6400 and M2400) , Replacing the LED Display Panel and Brackets (E6400 and M2400) or Replacing the Display Panel and Brackets (E6400 ATG) ).  3. Replace the display bezel (see Replac ...

  • Dell E6400 - page 46

    Back to Contents Page  Fan Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the Fan  Replacing the Fan  Removing the Fan   1. Follow the instructions in Before Working on Your Computer .  2. Remove the bottom of the base assembly (see Remov ...

  • Dell E6400 - page 47

    Back to Contents Page  ...

  • Dell E6400 - page 48

    Back to Contents Page  FCM Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing an FCM from the WWAN/FCM Slot  Removing an FCM from the WPAN/UWB/FCM Slot  Replacing an FCM  The FCM is also known as Intel ® Turbo Memory and the Intel Flash Cach ...

  • Dell E6400 - page 49

     Replacing an FCM  1. Slide the FCM into the card connector on the system board.  2. Press the FCM down and hold it in place.  3. Replace the M2 x 3 - mm screw.  4. Secure the wireless cables: If you are installing the FCM in the WWAN/FCM slot, place the gray/black and gray/white antenna cables in the holder next to the module. If yo ...

  • Dell E6400 - page 50

     5. Replace the bottom of the base assembly (see Replacing the Bottom of the Base Assembly ).  6. Follow the procedures in After Working on Your Computer . Back to Contents Page  1 holder by module 2 blue antenna cable 3 FCM   ...

  • Dell E6400 - page 51

    Back to Contents Page  Hard Drive Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the Hard Drive  Replacing the Hard Drive  Removing the 1.8" Hard Drive (E6400 ATG)  Replacing the 1.8" Hard Drive (E6400 ATG)  Removing the M ...

  • Dell E6400 - page 52

     Replacing the Hard Drive   1. Hold the hard drive with the label facing down.  2. Place the pin on one end of the bezel into the hole on the hard drive.  3. On the other end of the bezel, replace the M3 x 3 - mm screw that secures the hard drive bezel to the hard drive.  4. Slide the hard drive into the hard drive bay.  5. Rep ...

  • Dell E6400 - page 53

     5. Remove the M3 x 3 - mm screw on the hard drive bezel.  6. Remove the hard drive bezel.  7. Remove the two M2.5 x 5 - mm screws from the cover of the hard drive carrier.  8. Lift the cover up at an angle and slide the tabs on the cover out from the carrier.  9. Lift the hard drive up an angle and slide it out from the connector on ...

  • Dell E6400 - page 54

     10. Pull out on the sides of the blue bumper to remove it from the hard drive.  Replacing the 1.8" Hard Drive (E6400 ATG)   1. With the top of the bumper facing up, place the end of the blue bumper on the end of the hard drive opposite from the connector, then enclose the two sides of the hard drive with the blue bumper.  2. Pl ...

  • Dell E6400 - page 55

     3. Connect the hard drive to the connector in the carrier.  4. Slide the tabs on the cover under the lip on the hard drive carrier.  5. Replace the two M2.5 x 5 - mm screws.  6. Place the pin on one end of the bezel into the hole on the hard drive.  7. On the other end of the bezel, replace the M3 x 3 - mm screw that secures the har ...

  • Dell E6400 - page 56

     1. Follow the procedures in Working on Your Computer .  2. Turn your computer upside down.  3. If your computer has a security screw for the modular drive, remove the security screw.  4. Push the release latch in to release it.  5. Use the release latch to slide the drive out of the modular bay.  6. Remove the M2.5 x 5 - mm screw ...

  • Dell E6400 - page 57

     10. Remove the three M2.5 x 5 - mm screws on the cover of the hard drive carrier.  11. Lift the cover up at an angle and remove.  12. Remove the four M2.5 x 5 screws from the hard drive bracket.  13. Lift the hard drive up at an angle and disconnect it from the hard drive carrier. 1 M2.5 x 5 - mm screw 2 release latch carrier 3 hard dr ...

  • Dell E6400 - page 58

     14. Lift the connector - end of the hard drive and remove the hard drive from the hard drive bracket.  15. Pull out on the sides of the blue bumper to remove it from the hard drive.  Replacing the Modular Hard Drive   1. With the top of the bumper facing up, place the end of the blue bumper on the end of the hard drive opposite from ...

  • Dell E6400 - page 59

     2. Place the end that is opposite from the connector on the hard drive into the hard drive bracket, ensuring that the hard drive fits into each corner of the hard drive bracket.  3. Lower the hard drive into the hard drive bracket.  4. Place the hard drive into the carrier at an angle.  5. Connect the hard drive to the connector in the ...

  • Dell E6400 - page 60

     7. Attach the side of the cover where it is angled, ensuring the tabs on the cover fit properly into the notches on the carrier.  8. Set the cover in place and replace the three M2.5 x 5 - mm screws.  9. Slide the release latch carrier into the hard drive carrier.  10. Replace the M2.5 x 5 - mm screw that holds the carrier for the rele ...

  • Dell E6400 - page 61

     13. Slide the hard drive carrier into the modular bay.  14. Push the release latch in to hold the carrier in place.  15. If your computer has a security screw for the modular drive, replace the security screw.  16. Follow the procedures in After Working on Your Computer .  17. Install the operating system, drivers, and utilities for ...

  • Dell E6400 - page 62

    Back to Contents Page  Hinge Covers Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the Hinge Covers  Replacing the Hinge Covers  Removing the Hinge Covers  The hinge covers are not interchangeable; the left one covers the DisplayPort connector ...

  • Dell E6400 - page 63

    Back to Contents Page  Keyboard Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the Keyboard  Replacing the Keyboard  Removing the Keyboard   1. Follow the procedures in Before Working on Your Computer .  2. Remove the LED cover (see Remov ...

  • Dell E6400 - page 64

     4. Replace the LED cover (see Replacing the LED Cover ).  5. Follow the procedures in After Working on Your Computer . Back to Contents Page  1 M2 x 3 - mm screws (2) 2 tabs (5) 3 keyboard connector   ...

  • Dell E6400 - page 65

    Back to Contents Page  LED Cover Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the LED Cover  Replacing the LED Cover  Removing the LED Cover   1. Follow the procedures in Before Working on Your Computer .  2. Locate the tabs in the batt ...

  • Dell E6400 - page 66

    Back to Contents Page  ...

  • Dell E6400 - page 67

    Back to Contents Page  Memory Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing a Memory Module  Replacing a Memory Module Your computer has two user - accessible SODIMM sockets. You can increase your computer memory by installing memory modules on the ...

  • Dell E6400 - page 68

     3. Replace the bottom of the base assembly (see Replacing the Bottom of the Base Assembly ).  4. Follow the procedures in After Working on Your Computer . As the computer boots, it detects the additional memory and automatically updates the system configuration information. To confirm the amount of memory installed in the computer: l  In ...

  • Dell E6400 - page 69

    Back to Contents Page  Modem Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the Modem  Replacing the Modem  Removing the Modem   1. Follow the procedures in Before Working on Your Computer .  2. Remove the LED cover (see Removing the LED ...

  • Dell E6400 - page 70

    Back to Contents Page  ...

  • Dell E6400 - page 71

    Back to Contents Page  Modular Drive Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the Modular Drive  Replacing the Modular Drive The modular drive supports either a second hard drive, an optical drive, or a an air bay for travel.  Removing the M ...

  • Dell E6400 - page 72

    Back to Contents Page  Palm Rest Assembly Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the Palm Rest Assembly  Replacing the Palm Rest Assembly  Removing the Palm Rest Assembly   1. Follow the instructions in Before Working on Your Compute ...

  • Dell E6400 - page 73

     Replacing the Palm Rest Assembly   1. Holding the palm rest at an angle, connect the front of the palm rest to the computer, securing all snaps.  2. Lower and snap the left side into place.  3. Connect the contactless smart card cable, the touchpad cable, the speaker cable, and the wireless switch cable to the system board.  4. R ...

  • Dell E6400 - page 74

    Back to Contents Page  DC Power Cable Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the DC Power Cable  Replacing the DC Power Cable  Removing the DC Power Cable   1. Follow the instructions in Before Working on Your Computer .  2. Remov ...

  • Dell E6400 - page 75

      1. Place the DC power cable in the base assembly, aligning the guides on the connector sides with the base.  2. Route the DC power cable in the base assembly.  3. Replace the system board (see Replacing the System Board Assembly ).  4. Replace the card cage (see Replacing the Card Cage ).  5. Replace the palm rest assembly (see ...

  • Dell E6400 - page 76

    Back to Contents Page  RJ - 11 Modem Connector Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the RJ - 11 Modem Connector  Replacing the RJ - 11 Modem Connector  Removing the RJ - 11 Modem Connector   1. Follow the procedures in Before Worki ...

  • Dell E6400 - page 77

     2. Replace the modem (see Replacing the Modem ).  3. Replace the palm rest assembly ( Replacing the Palm Rest Assembly ).  4. Replace the right speaker grill (see Replacing the Right Speaker Grill/Fingerprint Reader Assembly ).  5. Replace the keyboard (see Replacing the Keyboard ).  6. Replace the LED cover (see Replacing the LED C ...

  • Dell E6400 - page 78

    Back to Contents Page  Right Speaker Grill/Fingerprint Reader Assembly Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the Right Speaker Grill/Fingerprint Reader Assembly  Replacing the Right Speaker Grill/Fingerprint Reader Assembly  Removing the ...

  • Dell E6400 - page 79

     Replacing the Right Speaker Grill/Fingerprint Reader Assembly   1. Snap the right speaker grill into place on the palm rest.  2. If your computer has a fingerprint reader, connect the fingerprint reader cable. Press the length of the cable to secure it to the palm rest.  3. Replace the keyboard (see Replacing the Keyboard ).  4. ...

  • Dell E6400 - page 80

    Back to Contents Page  System Board Assembly Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the System Board Assembly  Replacing the System Board Assembly The system board's BIOS chip contains the Service Tag, which is also visible on a barcode ...

  • Dell E6400 - page 81

    25. Lift the system board out of the base assembly.  Replacing the System Board Assembly   1. Place the front - edge of the system board into the base of the computer, ensuring the system board fits under the metal LCD latch mechanism in the front center of the base assembly.  2. Connect the DC power cable to the bottom of the system bo ...

  • Dell E6400 - page 82

    18. Replace the heatsink assembly (see Replacing the Processor Heatsink Assembly ).  19. Replace the memory modules (see Replacing a Memory Module ).  20. Replace the card in the WPAN/UWB/FCM card slot, if applicable (see Replacing a WPAN (UWB/BT) Card or Replacing an FCM ).  21. Replace the card from the WLAN/WiMax card slot, if applicabl ...

  • Dell E6400 - page 83

    Back to Contents Page  Troubleshooting Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Troubleshooting Tools  Solving Problems  Dell Technical Update Service  Dell Support Utility  Troubleshooting Tools  Diagnostic Lights  Your computer ha ...

  • Dell E6400 - page 84

     Hardware Troubleshooter If a device is either not detected during the operating system setup or is detected, but incorrectly configured, you can use the Hardware Troubleshooter to resolve the incompatibility. Microsoft ® W indows ® XP :  1. Click Start ® Help and Support .  2. Type hardware troubleshooter in the search field and press ...

  • Dell E6400 - page 85

    ¡  During the assessment, answer any questions that appear. ¡  If failures are detected during the Pre - boot System Assessment, write down the error code(s) and contact Dell Support. ¡  If the Pre - boot System Assessment completes successfully, the following message appears: " Booting Dell Diagnostic Utility Partition. Press any ...

  • Dell E6400 - page 86

     10. After all tests have completed, close the test window to return to the Dell Diagnostics Main Menu.  11. Close the Main Menu window to exit the Dell Diagnostics and restart the computer.  12. Remove the Drivers and Utilities media from the optical drive.  Dell Diagnostics Main Menu After the Dell Diagnostics loads, the following men ...

  • Dell E6400 - page 87

    Error Messages  If the error message is not listed, see the documentation for the operating system or the program that was running when the message appeared.  A filename cannot contain any of the following characters: / : * ? " < > | —  Do not use these characters in filenames.  A required .DLL file was not found — The ...

  • Dell E6400 - page 88

     Ensure that Microsoft Windows Recognizes the drive — Windows XP : l  Click Start and click My Computer . Windows Vista : l  Click the Windows Vista Start button and click Computer . If the drive is not listed, perform a full scan with your antivirus software to check for and remove viruses. Viruses can sometimes prevent Windows from rec ...

  • Dell E6400 - page 89

     Run Check Disk —  Windows XP : 1.  Click Start and click My Computer . 2.  Right - click Local Disk C: . 3.  Click Properties ® Tools ® Check Now . 4.  Click Scan for and attempt recovery of bad sectors and click Start . Windows Vista : 1.  Click Start and click Computer . 2.  Right - click Local Disk C: . 3.  Click ...

  • Dell E6400 - page 90

    The computer stops responding  Turn the computer off — If you are unable to get a response by pressing a key on your keyboard or moving your mouse, press and hold the power button for at least 8 to 10 seconds (until the computer turns off), and then restart your computer.  A program stops responding  End the program 1.  Press <Ctrl ...

  • Dell E6400 - page 91

    Use a virus - scanning program to check the hard drive, floppy disks, CDs, or DVDs  Save and close any open files or programs and shut down your computer through the Start menu  Memory Problems   If you receive an insufficient memory message —  l  Save and close any open files and exit any open programs you are not using to see ...

  • Dell E6400 - page 92

     No sound from headphones  Check the headphone cable connection — Ensure that the headphone cable is securely inserted into the headphone connector. See the Setup and Quick Reference Guide for your computer at support.dell.com .  Adjust the Windows volume control — Click or double - click the speaker icon in the lower - right corner of ...

  • Dell E6400 - page 93

    utility for self - support information, software updates, and health scans of your computing environment.  Accessing the Dell Support Utility Access the Dell Support Utility from the icon on the taskbar or from the Start menu. If the Dell Support icon does not appear in your taskbar:  1. Click Start ® All Programs ® Dell Support ® Dell Sup ...

  • Dell E6400 - page 94

    Back to Contents Page  WLAN/WiMax Card Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing the WLAN/WiMax Card  Replacing the WLAN/WiMax Card   Removing the WLAN/WiMax Card  1. Follow the procedures in Before Working on Your Computer .  2. Rem ...

  • Dell E6400 - page 95

     Replacing the WLAN/WiMax Card  1. Slide the card into the connector labeled WLAN/WiMax.  2. Press the card down and hold it in place.  3. Replace the M2 x 3 - mm screw.  4. Connect the appropriate antenna cables to the card you are installing: If the card has two triangles on the label (white and black), connect the white antenna ca ...

  • Dell E6400 - page 96

    Back to Contents Page  WPAN (UWB/BT) Card Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing a WPAN (UWB/BT) Card  Replacing a WPAN (UWB/BT) Card   Removing a WPAN (UWB/BT) Card  1. Follow the procedures in Before Working on Your Computer .  ...

  • Dell E6400 - page 97

     Replacing a WPAN (UWB/BT) Card  1. Slide the card into the connector labeled WPAN/UWB/FCM.  2. Press the card down and hold it in place.  3. Replace the M2 x 3 - mm screw.  4. Connect the blue antenna cable to the WPAN card.  5. Slide the left hinge cover back in place and replace the M2.5 x 5 - mm screw on the hinge cover.  6 ...

  • Dell E6400 - page 98

    Back to Contents Page  WWAN Card Dell™Latitude™E6400andE6400ATGand MobileWorkstationPrecision™M2400ServiceManual  Removing a WWAN Card  Replacing a WWAN Card   Removing a WWAN Card  1. Follow the procedures in Before Working on Your Computer .  2. Remove the bottom of the base ass ...

  • Dell E6400 - page 99

     1. Slide the card into the connector labeled WWAN/FCM.  2. Press the card down and hold it in place.  3. Replace the M2 x 3 - mm screw.  4. Connect the white antenna cable to the connector labeled "main" (white triangle), and connect the black antenna cable to the connector labeled "aux" (black triangle).  5. Rep ...

Manufacturer Dell Category Laptop

Documents that we receive from a manufacturer of a Dell E6400 can be divided into several groups. They are, among others:
- Dell technical drawings
- E6400 manuals
- Dell product data sheets
- information booklets
- or energy labels Dell E6400
All of them are important, but the most important information from the point of view of use of the device are in the user manual Dell E6400.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Dell E6400, service manual, brief instructions and user manuals Dell E6400. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Dell E6400.

Similar manuals

A complete manual for the device Dell E6400, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Dell E6400 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Dell E6400.

A complete Dell manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Dell E6400 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Dell E6400, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Dell E6400, that we can find in the current document
3. Tips how to use the basic functions of the device Dell E6400 - which should help us in our first steps of using Dell E6400
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Dell E6400
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Dell E6400 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Dell E6400?

Use the form below

If you did not solve your problem by using a manual Dell E6400, ask a question using the form below. If a user had a similar problem with Dell E6400 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)