English dropdown-ico

Manual Hotpoint NLL113

24 pages 0.45 mb
Download

Go to site of 24

Summary
  • Hotpoint NLL113 - page 1

    Hotpoint.com NLL113 NVL333 Dr y ers 134204000 175D1807P417 39-90153 11-02 JR Safety Instr uctions . . . . . . . . . 2–4 Operating Instr uctions Control Panels . . . . . . . . . . . . . . . .5 Control Settings . . . . . . . . . . . . . . .5 Loading and Using the Dryer . . .6, 7 Installation Instr uctions Electrical Requirements . . . . . . . . 9 E ...

  • Hotpoint NLL113 - page 2

    IMPORT ANT SAFETY INFORMA TION. READ ALL INSTRUCTIONS BEFORE USING. ■ Properly ground dryer to conform with all governing codes and ordinances. Follow details in the Installation Instructions section. ■ Install or store where it will not be exposed to temperatures below freezing or exposed to the weather . ■ Connect to a properly rated, prote ...

  • Hotpoint NLL113 - page 3

    ■ Never reach into the dryer while the drum is moving. Before loading, unloading or adding clothes, wait until the drum has completely stopped. ■ Clean the lint filter before each load to prevent lint accumulation inside the dryer or in the room. DO NOT OPERA TE THE DR YER WITHOUT THE LINT FIL TER IN PLACE, UNLESS THE DR YING RACK IS IN USE. ? ...

  • Hotpoint NLL113 - page 4

    4 WHEN USING YOUR DRYER (cont.) ■ Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug. ■ The interior of the machine and the exhaust duct connection inside the dryer should be cleaned at least once a year by a qualified technician. See ...

  • Hotpoint NLL113 - page 5

    5 About the control panel. Hotpoint.com Y ou can locate your model number on the label on the front of the left side of the door opening. Model NVL333 OFF LESS DRY Model NLL113 1 2 1 2 Consumer Support T roubleshooting T ips Operating Instructions Safety Instructions Installation Instructions IMPORT ANT : Clean the lint filter each time you use the ...

  • Hotpoint NLL113 - page 6

    6 The Exterior: Wipe or dust any spills or washing compounds with a damp cloth. Dryer control panel and finishes may be damaged by some laundry pretreatment soil and stain remover products. Apply these products away from the dryer . The fabric may then be washed and dried normally . Damage to your dryer caused by these products is not covered by yo ...

  • Hotpoint NLL113 - page 7

    7 Machine wash cycle Normal Permanent Press/ wrinkle resistant Gentle/ delicate Hand wash Do not wash Do not wring Water temperature Hot (50 ° C/120 ° F) Warm (40 ° C/105 ° F) Cold/cool (30 ° C/85 ° F) Tumble dry Dry Normal Permanent Press/ wrinkle resistant Gentle/ delicate Do not tumble dry Do not dry (used with do not wash) Heat setting Hi ...

  • Hotpoint NLL113 - page 8

    Prepare the area and exhaust for installation of the new dryer . Check to be sure that the existing external exhaust is clean and that it meets attached installation specifications. Using the four shipping carton corner posts as padding (two on each side), carefully lay the dryer on its left side and remove foam shipping pad. CAUTION: T o prevent d ...

  • Hotpoint NLL113 - page 9

    9 Electrical Connection Information for Gas Dryers W ARNING — T o reduce the risk of fire, electric shock or personal injury: • DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE. • DO NOT , UNDER ANY CIRCUMST ANCES, CUT OR REMOVE THE THIRD GROUNDING PRONG FROM THE POWER CORD. This dryer must be electrically grounded in accor ...

  • Hotpoint NLL113 - page 10

    If all rigid metal duct cannot be used, then flexible all-metal venting can be used, but it will reduce the maximum recommended duct length. In special installations when it is impossible to make a connection with the above recommendations, then UL-listed clothes dryer transition duct may be used as transition venting between the dryer and wall con ...

  • Hotpoint NLL113 - page 11

    Replace brass connecting pipe that is not plastic-coated. Stainless steel or plastic-coated brass MUST be used. W ARNING: Never reuse old flexible connectors. The use of old flexible connectors can cause gas leaks and personal injury . Always use NEW flexible connectors when installing a gas appliance. Installation MUST conform with local codes, or ...

  • Hotpoint NLL113 - page 12

    12 Do Not Install the Dryer: Do not install the dryer in an area exposed to dripping water or outside weather conditions. Do not install the dryer in an area where it will come in contact with curtains, drapes or anything that will obstruct the flow of combustion and ventilation air . Do not install the dryer on carpet. Floor MUST be solid with a m ...

  • Hotpoint NLL113 - page 13

    13 Rough-In Dimensions Dryer MUST be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support combustion. Metal ducting must be 4 ″ (10.16 cm) in diameter with no obstructions. Rigid metal duct is preferred. If dryer is exhausted through the floor , the exhaust system MUST NOT terminate beneath the mobil ...

  • Hotpoint NLL113 - page 14

    14 DANGER: Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a licensed electrician if you are in doubt as to whether the appliance is properly grounded. Grounding must be in accordance with local codes and ordinances, or in the absence of local codes, in accordance with the National Electri ...

  • Hotpoint NLL113 - page 15

    Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner . Install a UL-approved strain relief into the power cord entry hole of the mounting bracket. Use a strain relief which attaches to the mounting bracket with a nut. Finger -tighten the nut only at this time ...

  • Hotpoint NLL113 - page 16

    16 Remove the shipping cap from gas pipe at the rear of the dryer . NOTE: DO NOT connect the dr yer to LP gas ser vice without converting the gas valve. An LP conversion kit (Pub. No. 14-A038) MUST be installed by a qualified gas technician. Connect a 1/2 ″ (1.27 cm) I.D. semi-rigid or approved pipe from gas supply line to the 3/8 ″ (0.96 cm) p ...

  • Hotpoint NLL113 - page 17

    17 Reversing the Dryer Door Swing Open the dryer door . Remove the 4 hinge hole plugs or screws from the left side of door opening. Place nearby for future installation. NOTE: Y ou may need a plastic knife to help pull out the plugs. Be careful not to scratch the paint. Remove the four screws that secure the door hinges to the dryer front panel. NO ...

  • Hotpoint NLL113 - page 18

    Problem Possible Causes What T o Do Dryer doesn’t start Dr yer is unplugged • Make sure the dryer plug is pushed completely into the outlet. Fuse is blown/circuit breaker • Check the household Distribution Panel fuse/circuit is tripped breaker box in your home, and replace fuse or reset breaker . NOTE: Electric dr yers use two fuses or breake ...

  • Hotpoint NLL113 - page 19

    19 Consumer Support T roubleshooting T ips Operating Instructions Safety Instructions Installation Instructions Hotpoint.com Problem Possible Causes What T o Do Inconsistent T ype of heat • Automatic drying times will var y according to the type drying times of heat used (electric, natural or LP gas), size of load, types of fabrics, wetness of cl ...

  • Hotpoint NLL113 - page 20

    20 Consumer Support T roubleshooting T ips Operating Instructions Safety Instructions Installation Instructions Notes. ...

  • Hotpoint NLL113 - page 21

    General Electric Company W ar ranty Registration Depar tment P .O. Box 32150 Louisville, KY 40232-2150 GE Ser vice Protection Plus ™ GE, a name recognized worldwide for quality and dependability , offers you Ser vice Protection Plus ™ —comprehensive protection on all your appliances— No Matter What Brand! Benefits Include: • Backed by GE ...

  • Hotpoint NLL113 - page 22

    Consumer Pr oduct Ownership Registration I m p o r t a n t M a i l T o d a y ! General Electric Company Louisville, Kentucky GEAppliances.com First Name Mr . ■ ■ Ms. ■ ■ Mrs. ■ ■ Miss ■ ■ Street Address City State Date Placed In Use Month Day Y ear Zip Code Apt. # Last Name Phone Number _ _ Consumer Pr oduct Ownership Registration D ...

  • Hotpoint NLL113 - page 23

    23 For The Period Of: W e Will Replace: One Y ear Any part of the dr yer which fails due to a defect in materials or workmanship. During this From the date of the full one-year warranty , we will also provide, free of charge, all labor and in-home ser vice to original purchase replace the defective part. ■ Ser vice trips to your home to teach you ...

  • Hotpoint NLL113 - page 24

    Printed in the United States Consumer Support. Hotpoint W ebsite Hotpoint.com Have a question or need assistance with your appliance? T r y the Hotpoint W ebsite 24 hours a day , any day of the year! Y ou can also shop for more great Hotpoint products and take advantage of all of our on-line support services designed for your convenience. Schedule ...

Manufacturer Hotpoint Category Clothes Dryer

Documents that we receive from a manufacturer of a Hotpoint NLL113 can be divided into several groups. They are, among others:
- Hotpoint technical drawings
- NLL113 manuals
- Hotpoint product data sheets
- information booklets
- or energy labels Hotpoint NLL113
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hotpoint NLL113.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hotpoint NLL113, service manual, brief instructions and user manuals Hotpoint NLL113. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hotpoint NLL113.

Similar manuals

A complete manual for the device Hotpoint NLL113, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hotpoint NLL113 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hotpoint NLL113.

A complete Hotpoint manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hotpoint NLL113 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hotpoint NLL113, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hotpoint NLL113, that we can find in the current document
3. Tips how to use the basic functions of the device Hotpoint NLL113 - which should help us in our first steps of using Hotpoint NLL113
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hotpoint NLL113
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hotpoint NLL113 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hotpoint NLL113?

Use the form below

If you did not solve your problem by using a manual Hotpoint NLL113, ask a question using the form below. If a user had a similar problem with Hotpoint NLL113 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)