English dropdown-ico

Manual Cisco Blower Module Cisco 10000 ESR

22 pages 2.13 mb
Download

Go to site of 22

Summary
  • Cisco Blower Module Cisco 10000 ESR - page 1

    Corporate Headqu arters: Cisco Systems, Inc., 170 We st Tasman Drive, San Jose, CA 95134-1706 USA Copyright © 20 0 0. Cisco Systems, Inc. All rights reserved. 78-10832-01 Cisco 10000 ESR AC Power Entry Module Installation This publication contains instructions for installing the A C Po wer Entry Module (PEM) in the Cisco 10000 Edge Services Router ...

  • Cisco Blower Module Cisco 10000 ESR - page 2

    Product Description 2 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Product Description The A C PEM provides po wer con version directly fro m the facility V A C input po wer (100 V A C to 240 V A C) to the –48V VDC used internally b y the system (see Figure 1). A C power is deli v ered to the A C PEM from the V A C connection p ...

  • Cisco Blower Module Cisco 10000 ESR - page 3

    3 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Prerequisites and Preparation Prerequisites and Preparation Before you perform an y of the p rocedures in this guide, Cisco recommend s that you: • Read the safety guidelin es in the nex t section and re vie w the electrical safety and ESD-pre vention guidelines in the Cisco 10000 ...

  • Cisco Blower Module Cisco 10000 ESR - page 4

    Installation Guidelines 4 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 War ni ng This warning symbo l means danger . Y ou are in a situation that could cause bodily inju ry . Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard p ractices for preventing accide ...

  • Cisco Blower Module Cisco 10000 ESR - page 5

    5 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Adding or Replacing an AC PEM This section describes how to add or replace an A C PEM in the Cisco 10000 chassis. It contains the follo wing procedures: • Remov ing the Front Cov er , page 5 • Installing a Second A C PEM, page 7 • Replacing an A C ...

  • Cisco Blower Module Cisco 10000 ESR - page 6

    Adding or Replacing an A C PEM 6 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 2 Remov e the cov er by li fting it up sli ghtly and then pulling it t o ward you (Figure 3). Figur e 3 Removing the Fr ont Cov er Step 3 Continue instal ling or replacing the A C PEM: • If you are installing a second A C PEM, go to the “I nsta ...

  • Cisco Blower Module Cisco 10000 ESR - page 7

    7 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Installing a Second AC PEM Use the follo wing procedure to install a second A C PEM in the bottom po wer bay for redundanc y . Step 1 Attach an antistatic wr ist strap to your wr ist and to an ESD socket on the chassis, or to a bare metal surf ace on the ...

  • Cisco Blower Module Cisco 10000 ESR - page 8

    Adding or Replacing an A C PEM 8 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 2 Loosen the capti v e scre ws to remov e the blank co v er from the bottom po wer bay (Figure 5). Figur e 5 Removing the Blank Co v er 1 3 2 4 0A PROCESSOR PROCESSOR FANS OK FAN FAILURE MULTI- FAN FAILURE W h e n h o t s w a p p in g th is fa n tr ...

  • Cisco Blower Module Cisco 10000 ESR - page 9

    9 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Step 3 Install the ne w AC PEM all t he way into the po wer bay to ensure a secure connection to the backplane, and then tighten the captive scre ws (Figure 6 ). Figur e 6 Installing an A C PEM 1 3 2 4 0A PROCESSOR PROCESSOR FANS OK FAN FAILURE MULTI- FA ...

  • Cisco Blower Module Cisco 10000 ESR - page 10

    Adding or Replacing an A C PEM 10 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 4 Connect the po wer cord from the PEM to your po wer cord that connects to th e faci lity V A C input. Step 5 Set the A C power cord connec tors in a cord st rain relief (canoe) to pre vent them from accidently di sconnecting (Figu re 7). Figur e ...

  • Cisco Blower Module Cisco 10000 ESR - page 11

    11 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Step 7 Set the po wer switch to the on (|) positi on (Figure 8). The (green) po wer LED on the PEM lights indicating that the PEM is on. Figur e 8 Setting the A C P ow er S witch t o the On P osition Step 8 Replace the front cover . 32231 1 3 2 4 0A P R ...

  • Cisco Blower Module Cisco 10000 ESR - page 12

    Adding or Replacing an A C PEM 12 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Replacing an AC PEM Use the following procedure to replace an A C PEM. Note The illustrations in this guide sho w how to replace the A C PEM from the bottom po wer bay . The procedure is the same to replace an A C PEM in the top po wer bay . Step 1 Att ...

  • Cisco Blower Module Cisco 10000 ESR - page 13

    13 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Step 2 Po wer of f the PEM you are replacing (Figure 10). Caution Do not po wer off both A C PEMs in a redundant system or the system shuts do wn and all data traff ic stops. Only po wer of f the A C PEM you are replacing. Figur e 1 0 Sett ing the A C P ...

  • Cisco Blower Module Cisco 10000 ESR - page 14

    Adding or Replacing an A C PEM 14 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 3 Remov e the PEM power cable from its can o e and disconnect it from the A C input po wer cable (Figure 11). Figur e 1 1 AC P ow er Cor d Connect ors in Canoes 32235 1 3 2 4 0A PR O C E SS O R O N LY 0B 5 6 7 8 P R O CE S SO R O N LY POWER FAULT ...

  • Cisco Blower Module Cisco 10000 ESR - page 15

    15 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Step 4 Loosen the captiv e scre ws on the PEM and remo ve the PEM from the chassis using the handle on the faceplate (Figure 12). Figur e 12 Removing an A C PEM 1 3 2 4 0A PROCESSOR PROCESSOR FANS OK FAN FAILURE MULTI- FAN FAILURE W h e n h o t s w a p ...

  • Cisco Blower Module Cisco 10000 ESR - page 16

    Adding or Replacing an A C PEM 16 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 5 Install the ne w PEM all the way into the po wer bay to ensure a good connection to the backplane, and tighten the ca ptiv e scre ws on the PEM (Figure 13). Figur e 13 Installing an AC PEM 1 3 2 4 0A PROCESSOR PROCESSOR FANS OK FAN FAILURE MULTI ...

  • Cisco Blower Module Cisco 10000 ESR - page 17

    17 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Step 6 Connect the po wer cord from the PEM to the po wer cord that connects to the faci lity V A C input. Step 7 Set the A C power cord connec tors in a cord st rain relief (canoe) to pre vent them from accidentl y disconnecting ( Figure 14). Figur e 1 ...

  • Cisco Blower Module Cisco 10000 ESR - page 18

    Adding or Replacing an A C PEM 18 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Step 9 Set the po wer switch to the on (|) positi on (Figure 15) . The (green) po wer LED on the PEM lights indicating that the PEM is on. Figur e 15 Set ting the A C P ow er Switc h t o the On P osition Step 10 Replace the front cover . 32231 1 3 2 4 ...

  • Cisco Blower Module Cisco 10000 ESR - page 19

    19 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Adding or Replacing an AC PEM Troubleshooting the Installation T able 1 contai ns troubleshooting i nformation for th e A C PEM: T able 1 A C PEM T r oubleshooti ng Symptom Description System fails to power on Check that : • All A C pow er cords are properly connected to the Cisco ...

  • Cisco Blower Module Cisco 10000 ESR - page 20

    FCC Class A Compliance 20 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 FCC Class A Compliance This equipment has been tested and found to comply wi th the limits for a Class A digital de vice, pursuant to part 15 of the FCC rules. These limits are desi gned to pro vide reas onable p rotection agains t harmful i nterferen ce when ...

  • Cisco Blower Module Cisco 10000 ESR - page 21

    21 Cisco 10000 ESR AC Power Entry Module I nstallation 78-10832-01 Cisco Connection Online A vail able 24 hours a day , 7 days a week , CCO pro vides a wealth of standard and v alue-added services to Ci sco customers and b usiness partners. CCO services include prod uct information, product do cumentation, softw are updates, release notes, technica ...

  • Cisco Blower Module Cisco 10000 ESR - page 22

    Documentation CD-ROM 22 Cisco 10000 ESR AC Power Ent ry Module Installation 78-10832-01 Documentation CD-ROM Cisco documentation and add itional lite rature are a vailable in a CD-R OM package, which ships with your p roduct. The Documentation CD-R OM, a member of the Cisco Connectio n Family , is updated mon thly . Therefore, it might be more curr ...

Manufacturer Cisco Category Network Router

Documents that we receive from a manufacturer of a Cisco Blower Module Cisco 10000 ESR can be divided into several groups. They are, among others:
- Cisco technical drawings
- Blower Module 10000 ESR manuals
- Cisco product data sheets
- information booklets
- or energy labels Cisco Blower Module Cisco 10000 ESR
All of them are important, but the most important information from the point of view of use of the device are in the user manual Cisco Blower Module Cisco 10000 ESR.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Cisco Blower Module Cisco 10000 ESR, service manual, brief instructions and user manuals Cisco Blower Module Cisco 10000 ESR. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Cisco Blower Module Cisco 10000 ESR.

Similar manuals

A complete manual for the device Cisco Blower Module Cisco 10000 ESR, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Cisco Blower Module Cisco 10000 ESR by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Cisco Blower Module Cisco 10000 ESR.

A complete Cisco manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Cisco Blower Module Cisco 10000 ESR - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Cisco Blower Module Cisco 10000 ESR, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Cisco Blower Module Cisco 10000 ESR, that we can find in the current document
3. Tips how to use the basic functions of the device Cisco Blower Module Cisco 10000 ESR - which should help us in our first steps of using Cisco Blower Module Cisco 10000 ESR
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Cisco Blower Module Cisco 10000 ESR
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Cisco Blower Module Cisco 10000 ESR in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Cisco Blower Module Cisco 10000 ESR?

Use the form below

If you did not solve your problem by using a manual Cisco Blower Module Cisco 10000 ESR, ask a question using the form below. If a user had a similar problem with Cisco Blower Module Cisco 10000 ESR it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)