English dropdown-ico

Manual Antec SOLO II

26 pages 1.26 mb
Download

Go to site of 26

Summary
  • Antec SOLO II - page 1

    S O L O I I U SER M ANUAL S ILENCE R ENEWED ...

  • Antec SOLO II - page 2

    2 SOLO II U SER ’ S M ANUAL Congratulations on your purchase of the Antec SOLO II. The SOLO II emphasizes Quiet Computing™ and reinvents Antec’s renowned Sona ta line with a new set of attractive, practical features. Externally, the SOLO II’s dual-layer 1.0 mm S ECC / polycarbonate top & side panels absorb noise for exc eptional sound d ...

  • Antec SOLO II - page 3

    3 T ABLE O F C ONTENTS S ECTION 1: I NTRODUCTION 1.1 Getting to Know your Chassis ........... .................. ............ ............ ............. 5 1.2 Chassis Specif ications.......... ............. .................... ............ ............. ...........6 1.3 Included Scre ws ........... ............ .................... ............. . ...

  • Antec SOLO II - page 4

    4 I N T R O D U C T I O N S ECTION 1 ...

  • Antec SOLO II - page 5

    5 1.1 G ETTING TO KNOW YOUR CHASSIS 1. Internal: 3 x 3.5” / 2.5”using tray m ount OR 2 x 3.5” with suspension mount cable s 2. Internal: 1 x 2.5” SSD (dedicated) 3. External: 2 x 5.25” 4. 1 x rear 120 mm TrueQuiet™ fan with 2-speed s witch 5. 2 x front 120 mm fans (optional) and re movable, washable air filters 6. Anodized aluminum fron ...

  • Antec SOLO II - page 6

    6 1.2 C HASSIS S PECIFICATIONS Chassis Type Mid Tower Chassis Color Piano Black Dimensions 17.3” (H) x 8.1” (W) x 18.5” (D) 440 mm (H) x 20 5 mm (W) x 470 mm (D) Weight 20.2 lbs / 9.1 kg Cooling - Rear 120 mm TrueQuiet™ fan with preinstall ed silicon e gromm ets and 2-speed switch - 2 front 120 m m fan moun ts (opt ional) Drive Bays - 3 x 3 ...

  • Antec SOLO II - page 7

    7 1.4 B EFORE Y OU B EGIN In order to ensure that your build ing experience with the SOLO II will be a positiv e one, please take note of the following: • While working inside your SOLO II, ke ep your chassis on a flat, stable surfac e. Make sure your build environment is clean, well-lit, and free of dust. • Antec chassis feature rounded edges ...

  • Antec SOLO II - page 8

    8 H A R D W A R E I N S T A L L A T I O N S ECTION 2 ...

  • Antec SOLO II - page 9

    9 2.1 S ETTING U P Begin by removing the left side panel by lo osening the thumbscrews and swingin g the panel outward, pulling it back towards you; this will completely remove it. Cut the ties on the 5. 25” drive cage with a wire cutter and remove the plastic bag of screws. The SOLO II should now look like this. ...

  • Antec SOLO II - page 10

    10 2.2 M OTHERBOARD I NSTALLATION Before proceeding: Check the manual for your CPU cooler to fin d out if there are steps you must do before installing the motherboard. Make sure you have the co rrect I/O panel for your motherboard. If the panel provided with the chassis isn’t suitable, please c ontact your motherboard manufacturer for the cor re ...

  • Antec SOLO II - page 11

    11 3. Screw your motherboard into the standoffs with th e provided motherboard mo unting screws. 2.3 I NSTALLING THE KUHLER H 2 O The following instructs how to install the Ant ec KUHLER H 2 O liquid CPU cooler (620 / 920). For any other CPU coolers, please consult your manufac turer’s installation guide. Caution: - We strongly recommend installi ...

  • Antec SOLO II - page 12

    12 2. The TrueQuiet™ fan has two small black clips attached to the fan’ s two-speed switch. With your thumb and forefinger, spread the clips while pushing from the rear of the case to remove th e switch. 3. Preparing the KUHLER H 2 O backplate is specific to you r CPU socket. Please refer to the KUHLER H 2 O installation guide, available at htt ...

  • Antec SOLO II - page 13

    13 2. Remove the second screw with your other han d supporting the beam so the beam won’t drop. 3. Repeat steps 1 and 2 for the support beam screws at the rear of the case. . 4. Place the SOLO II on its side. Position the PSU into the mount and secure it with the PSU screws provided. If your PSU has a fan on its top side, make su re it aligns wit ...

  • Antec SOLO II - page 14

    14 2.5 C ABLE M ANAGEMENT There is a cable management area b etween the motherboard and right side pan el as well as cable hooks located on the side of the 3.5” drive cage. You c an tuck excess cables in this area or route them to the drive bays. Choose the cables you would like to pass thr ough the holes behind the motherboard tray. Pull them th ...

  • Antec SOLO II - page 15

    15 2. Attach the drive rails to your 5.25” device. Th ese rails have three depth settings t hat accommodate the depth of your 5.25” drive. 3. Make sure to properly align your drive rails wi th your 5.25” drive. We recommen d attaching one rail with one of the 5.25” drive screws and cl osing the bezel as a trial. Use the four 5.25” driv e ...

  • Antec SOLO II - page 16

    16 2.7 I NTERNAL 3.5” AND 2.5” I NSTALLATION ( TRAY M OUNTS AND SUSPEN SION MOUNTING SY STEM ) The following text outlines the preparator y stages for installing 3.5” / 2.5” drives u sing drives trays and the suspension mounting system. 1. If you have reattached it, remove the left side pan el. Loosen the side panel scre ws and swing the pa ...

  • Antec SOLO II - page 17

    17 5. Insert the 3.5” / 2.5” drive into the drive cage by pinch ing the ends of the drive tray and sliding the tray along the rails until the tray l ocks firmly into position. 6. Mount any other 3.5” / 2.5” devices accordingly. For Suspension Mounting Installation: The SOLO II accommodates two 3.5” drives using the suspension mounting sys ...

  • Antec SOLO II - page 18

    18 4. Twist the rear suspender and gu ide the hard drive through it. 5. Find the appropriate power connector on the PSU an d connect it to the device. 6. Repeat the same procedure for a second dri ve if necessary. 7. Close and secure the drive cage door. 2.8 I NTERNAL 2.5” D EVICE I NSTALLATION Toward the bottom-right of the m otherboard tray, yo ...

  • Antec SOLO II - page 19

    19 F RONT I/O P ORTS S ECTION 3 ...

  • Antec SOLO II - page 20

    20 Pin Signal Names Pin Signal Names 1 USB Power 1 2 USB Power 2 3 Negative Signal 1 4 Negative Signal 2 5 Positive Signal 1 6 Positive Signal 2 7 Ground 1 8 Ground 2 9 Key (No Connecti on) 10 Empty Pin 3.1 USB 2.0 Connect the front I/O panel USB cable to the USB header pin on your motherboard . Check your motherboard user’s manual to ensure that ...

  • Antec SOLO II - page 21

    21 Pin Signal Na me s (HDA ) Pin Signal Na me s (AC’9 7) 1 MIC2 L 1 MIC In 2 AGND 2 GND 3 MIC2 R 3 MICP o wer 4 AVC C 4 N C 5 FRO -R 5 Lin e Out (R) 6 MIC 2_ JD 6 Lin e Out (R) 7 F_ IO_ SEN 7 N C 8 Key(no pi n) 8 Key(no pi n) 9 FRO-L 9 Lin e Out (L) 10 LINE 2_JD 10 Lin e Out (L) 3.3 AC’97 / HD A UDIO P ORTS There is an Intel ® standard 10-pin ...

  • Antec SOLO II - page 22

    22 3.5 R EWIRING M OTHERBOARD H EADER C ONNECTIONS There may come a time wh en you need to reconfigure the pin-out of a motherboard header connector. Examples could be for your USB he ader, audio input header, or some other front panel connector such as the Power Button c onnector. Before performing any work, please refer to your motherboard user? ...

  • Antec SOLO II - page 23

    23 C OOLI NG S YSTEM S ECTION 4 ...

  • Antec SOLO II - page 24

    24 4.1 I NCLUDED 120 MM T RUE Q UIET ™ REAR FAN The SOLO II co mes with a 120 mm TrueQuiet™ rear fan. This fan h as a two-speed switch t hat lets y ou cho ose the speed be st suited to y our need. The switch is located at th e rear of the ca se. The d efault fan speed sett ing is Low. 120 mm Fan Specification s: Size: 120 x 25mm two -speed fan ...

  • Antec SOLO II - page 25

    25 4.3 O PTIONAL F ANS The SOLO II can accommodate two 1 20 mm front intake fans. The following sho ws you how to install one of thesefans using a 120 mm TrueQuiet™ fan: 1. Remove the fan filter as depicted in secti on 4.2. 2. Insert the mounting pin through the mounting hole tail-first. Pull the tail through the hole and push the pin through wit ...

  • Antec SOLO II - page 26

    26 Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 tel: 510-770-1 200 fax: 510-770-1 288 Antec Eur ope B .V. Stuttgartstra at 12 3047 AS Rott erdam The Netherland s tel: +49-40-2 26139-22 fax: +31 (0) 1 0 437-175 2 Technical Su pport : US &Canada 1-800-22ANTE C customersupp ort@antec. com Europe +31 (0) 10 462 -2060 europe.tech support@a ntec ...

Manufacturer Antec Category Personal Computer

Documents that we receive from a manufacturer of a Antec SOLO II can be divided into several groups. They are, among others:
- Antec technical drawings
- SOLO II manuals
- Antec product data sheets
- information booklets
- or energy labels Antec SOLO II
All of them are important, but the most important information from the point of view of use of the device are in the user manual Antec SOLO II.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Antec SOLO II, service manual, brief instructions and user manuals Antec SOLO II. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Antec SOLO II.

Similar manuals

A complete manual for the device Antec SOLO II, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Antec SOLO II by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Antec SOLO II.

A complete Antec manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Antec SOLO II - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Antec SOLO II, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Antec SOLO II, that we can find in the current document
3. Tips how to use the basic functions of the device Antec SOLO II - which should help us in our first steps of using Antec SOLO II
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Antec SOLO II
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Antec SOLO II in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Antec SOLO II?

Use the form below

If you did not solve your problem by using a manual Antec SOLO II, ask a question using the form below. If a user had a similar problem with Antec SOLO II it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)