English dropdown-ico

Manual Hoshizaki KM-250BWF

21 pages 0.6 mb
Download

Go to site of 21

Summary
  • Hoshizaki KM-250BWF - page 1

    ™ INSTRUCTION MANUAL ISSUED: March 14, 2000 KM-250BAF KM-250BWF SELF-CONT AINED CRESCENT CUBER R eliability is a beautiful thing TM REVISED: December 22, 2004 ...

  • Hoshizaki KM-250BWF - page 2

    2 Only qualified service technicians should attempt to install, service or maintain this icemaker. No installation, service or maintenance should be undertaken until the technician has thoroughly read this Instruction Manual. Likewise, the owner/manager should not proceed to operate the icemaker until the installer has instructed them on its proper ...

  • Hoshizaki KM-250BWF - page 3

    3 CONTENTS I. Specifications .............................................................................................................. ...... 4 1. Nameplate Rating ........................................................................................................ 4 [a] KM-250BAF (air-cooled) ............................................... ...

  • Hoshizaki KM-250BWF - page 4

    4 I. Specifications 1. Nameplate Rating [a] KM-250BAF (air-cooled) See the nameplate for electrical and refrigeration specifications. This nameplate is located on the upper right hand side of the rear panel. Since this nameplate is located on the rear panel of the icemaker, it cannot be read when the back of the icemaker is against a wall or agains ...

  • Hoshizaki KM-250BWF - page 5

    5 [b] KM-250BWF (water-cooled) See the nameplate for electrical and refrigeration specifications. This nameplate is located on the upper right hand side of the rear panel. Since this nameplate is located on the rear panel of the icemaker, it cannot be read when the back of the icemaker is against a wall or against another piece of kitchen equipment ...

  • Hoshizaki KM-250BWF - page 6

    6 2. Dimensions/Connections [a] KM-250BAF Units: millimeters (inches) ...

  • Hoshizaki KM-250BWF - page 7

    7 [b] KM-250BWF Units: millimeters (inches) ...

  • Hoshizaki KM-250BWF - page 8

    8 II. Installation and Operating Instructions 1. Checks Before Installation IMPORT ANT 1. Remove shipping cartons, tape(s) and packing. If any are left in the icemaker, it will not work properly. 2. Ensure all components, fasteners and thumbscrews are securely in place. 1) Remove the top panel and the front panel to prevent damage when installing t ...

  • Hoshizaki KM-250BWF - page 9

    9 2. Location IMPOR T ANT This icemaker is not intended for outdoor use. Normal operating ambient temperature should be within +45 ° F (7 ° C) to +100 ° F (38 ° C); Normal operating water temperature should be within +45 ° F (7 ° C) to +90 ° F (32 ° C). Operation of the icemaker, for extended periods, outside of these normal temperature ran ...

  • Hoshizaki KM-250BWF - page 10

    10 4. W ater Supply and Drain Connections See Fig. 1 CA UTION To prevent damage to the equipment, do not operate the icemaker when the water supply is OFF, or if the pressure is below 10 PSIG (0.7 bar). Do not run the icemaker until the proper water pressure is reached. • Water supply inlet is 1/2" FPT. Note: On water-cooled model, two water ...

  • Hoshizaki KM-250BWF - page 11

    11 KM-250BAF KM-250BWF Fig. 1 ...

  • Hoshizaki KM-250BWF - page 12

    12 5. Final Check List 1) Is the icemaker level? 2) Is the icemaker in a site where the ambient temperature is within +45 ° F (7 ° C) to +100 ° F (38 ° C) and the water temperature within +45 ° F (7 ° C) to +90 ° F (32 ° C) all year around? 3) Is there at least 6" (15 cm.) clearance at the rear and top of the icemaker for maintenance o ...

  • Hoshizaki KM-250BWF - page 13

    13 6. Startup CA UTION 1. All parts are factory-adjusted. Improper adjustments may result in failure. 2. If the unit is turned off, wait for at least 3 minutes before restarting the icemaker to prevent damage to the compressor. 1) Open the water supply line shut-off valve. 2) Remove the front panel. 3) Move the control switch on the control box, to ...

  • Hoshizaki KM-250BWF - page 14

    14 7. Preparing the Icemaker for Long Storage IMPOR T ANT When shutting off the icemaker for an extended time, drain out all water from the water line and remove the ice from the storage bin. The storage bin should be cleaned and dried. Drain the icemaker, using air or carbon dioxide, to prevent damage to the water supply line at sub-freezing tempe ...

  • Hoshizaki KM-250BWF - page 15

    15 5) Allow the line to drain by gravity. 6) Attach compressed air or carbon dioxide supply to the potable water line drain valve. 7) Move the control switch to the “ ICE ” position. 8) Blow the potable water line out using compressed air or carbon dioxide. [3] Drain the potable water tank: 1) Disconnect the power supply. 2) Move the control sw ...

  • Hoshizaki KM-250BWF - page 16

    16 III. Cleaning and Maintenance IMPORT ANT Ensure all components, fasteners and thumbscrews are securely in place after any maintenance or cleaning is done to the equipment. 1. Cleaning and Sanitizing Instructions W ARNING 1. HOSHIZAKI recommends cleaning this unit at least once a year. More frequent cleaning, however, may be required in some exis ...

  • Hoshizaki KM-250BWF - page 17

    17 4) Remove the plug at the bottom of the water tank to drain the tank. See Fig. 3. After draining, replace the plug in its correct position. 5) Pull out the cap at the front of the plastic body 1" or more. See Fig. 4. 6) Pour the cleaning solution into the water tank. 7) Replace the cap in its correct position. 8) Move the control switch to ...

  • Hoshizaki KM-250BWF - page 18

    18 [c] Sanitizing Solution Dilute 1 fl. oz. (30 ml or 2 tbs) of 5.25% sodium hypochlorite solution (chlorine bleach) with 2 gallons (7.6 l) of warm water. Using a chlorine test strip or other method, confirm that you have a concentration of about 200 ppm. IMPOR T ANT For safety and maximum effectiveness, use the solution immediately after dilution. ...

  • Hoshizaki KM-250BWF - page 19

    19 14) Move the control switch to the “ ICE ” position to fill the water tank with water. 15) After 3 minutes, move the control switch to the “ OFF ” position. 16) Move the control switch to the “ WASH ” position. 17) After 5 minutes, move the control switch to the “ OFF ” position. 18) Remove the plug to drain the water tank. After ...

  • Hoshizaki KM-250BWF - page 20

    20 2. Maintenance IMPOR T ANT This icemaker must be maintained individually, referring to the instruction manual and labels provided with the icemaker. 1) Exterior Panels To keep the exterior clean, wipe occasionally with a clean and soft cloth. Use a damp cloth containing a neutral cleaner to wipe off oil or dirt build up. 2) Storage Bin and Scoop ...

  • Hoshizaki KM-250BWF - page 21

    21 HOSHIZAKI HOSHIZAKI AMERICA, INC. 618 HIGHW A Y 74 SOUTH PEA CHTREE CITY , GA 30269 U.S.A. PHONE: 770-487-2331 91A1AQ10D ...

Manufacturer Hoshizaki Category Ice Maker

Documents that we receive from a manufacturer of a Hoshizaki KM-250BWF can be divided into several groups. They are, among others:
- Hoshizaki technical drawings
- KM-250BWF manuals
- Hoshizaki product data sheets
- information booklets
- or energy labels Hoshizaki KM-250BWF
All of them are important, but the most important information from the point of view of use of the device are in the user manual Hoshizaki KM-250BWF.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Hoshizaki KM-250BWF, service manual, brief instructions and user manuals Hoshizaki KM-250BWF. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Hoshizaki KM-250BWF.

Similar manuals

A complete manual for the device Hoshizaki KM-250BWF, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Hoshizaki KM-250BWF by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Hoshizaki KM-250BWF.

A complete Hoshizaki manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Hoshizaki KM-250BWF - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Hoshizaki KM-250BWF, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Hoshizaki KM-250BWF, that we can find in the current document
3. Tips how to use the basic functions of the device Hoshizaki KM-250BWF - which should help us in our first steps of using Hoshizaki KM-250BWF
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Hoshizaki KM-250BWF
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Hoshizaki KM-250BWF in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Hoshizaki KM-250BWF?

Use the form below

If you did not solve your problem by using a manual Hoshizaki KM-250BWF, ask a question using the form below. If a user had a similar problem with Hoshizaki KM-250BWF it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)