English dropdown-ico

Manual Icom IC-F60V

48 pages 0.77 mb
Download

Go to site of 48

Summary
  • Icom IC-F60V - page 1

    INSTRUCTION MANUAL This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. UHF TRANSCEIVER iF60V VHF TRANSCEIVER iF50V ! IC-F50V_F60V_0.qxd 07.8.6 10:36 AM Page A (1,1) ...

  • Icom IC-F60V - page 2

    i SAFETY TRAINING INFORMA TION Y our Icom radio generates RF electromagnetic energy during transmit mode. This radio is designed for and clas- sified as “Occupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such haz- ards. This radio is NOT intended fo ...

  • Icom IC-F60V - page 3

    ii G INFORMA TION • DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio. • DO NOT transmit for ...

  • Icom IC-F60V - page 4

    iii IMPOR T ANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver . SA VE THIS INSTRUCTION MANUAL— This instruction manual contains important operating instructions for the IC-F50V VHF TRANSCEIVER and IC-F60V UHF TRANSCEIVER . EXPLICIT DEFINITIONS OPERA TING NOTES • When transmitting with a portable radio, hold the rad ...

  • Icom IC-F60V - page 5

    iv PRECAUTIONS R W ARNING! NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body , especially the face or eyes, while transmitting. The transceiver will perform best if the microphone is 5 to 10 cm (2 to 4 inches) away from the lips and the transceiver is vertical. R W ARNING! NEVER operate the trans ...

  • Icom IC-F60V - page 6

    T ABLE OF CONTENTS SAFETY TRAINING INFORMA TION …………………………………………… i IMPORT ANT ……………………………………………………………………… iii EXPLICIT DEFINITIONS ………………………………………………………… iii OPERA TING NOTES …………………………………… ...

  • Icom IC-F60V - page 7

    1 1 ACCESSORIES 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ■ Supplied accessories * There are no names on the programmable function keys since the functions can be freely assigned to [P0] to [P3], [Red], [ ] and [ ] keys. Attach the supplied key stickers above the appropriate keys for easy recognition of that key’s assigned function. Ba ...

  • Icom IC-F60V - page 8

    2 1 ACCESSORIES ■ Accessory attachments D Flexible antenna Connect the supplied fl exible antenna to the antenna connector . CAUTION! • NEVER HOLD the antenna when carrying the transceiver . • T ransmitting without an antenna may damage the transceiver . ï Battery pack T o attach the battery pack: Slide the battery pack on the back of the t ...

  • Icom IC-F60V - page 9

    3 1 ACCESSORIES 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ï Jack cover Attach the jack cover when the optional equipment is not used. D Belt clip Attach the belt clip to the back of the transceiver with the supplied screws. Supplied screws w Jack cover [SP MIC] jack Screw q e r T o attach the jack cover: q Insert the jack cover into the [ ...

  • Icom IC-F60V - page 10

    4 2 P ANEL DESCRIPTION ■ Front, top and side panels q VOLUME CONTROL [VOL] T urns power ON and adjusts the audio level. w RED BUTTON The desired function can be assigned by your dealer . (p. 8) e ANTENNA CONNECTOR Connects the supplied antenna. (p. 2) Microphone Function display (p. 6) w e r t y u q i Speaker ! IC-F50V_F60V_0.qxd 07.8.6 10:36 AM ...

  • Icom IC-F60V - page 11

    5 2 P ANEL DESCRIPTION 2 r EXTERNAL SPEAKER-MICROPHONE JACK [SP MIC] Connects the optional speaker-microphone, etc. t DEALER-PROGRAMMABLE KEYS [P0] to [P3] The desired functions can be assigned independently by your dealer . (p. 8) y CH UP AND DOWN KEYS [ ]/[ ] Push to select an operating channel, etc. *Desired functions can be assigned independent ...

  • Icom IC-F60V - page 12

    6 2 P ANEL DESCRIPTION ■ Function display q RECORD INDICA TOR ➥ Appears when an unread message is in the memory . ➥ Blinks while recording. w LOW POWER INDICA TOR Appears when low output power is selected. e AUDIBLE INDICA TOR ➥ Appears when the channel is in the ‘ audible ’ (unmute) condition. ➥ Appears when the speci fi ed 2/5-tone ...

  • Icom IC-F60V - page 13

    7 2 P ANEL DESCRIPTION 2 i BA TTERY INDICA T OR Appears or blinks when the battery power decreases to a speci- fi ed level. o ALPHANUMERIC DISPLA Y Displays an operating channel number , channel names, Set mode contents, DTMF code, etc. * 1 BIIS operation only * 2 MDC operation only ! IC-F50V_F60V_0.qxd 07.8.6 10:36 AM Page 7 (1,1) ...

  • Icom IC-F60V - page 14

    8 2 P ANEL DESCRIPTION ■ Programmable function keys The following functions can be assigned to [P0] , [P1] , [P2] , [P3] , [Red] , [] and [] programmable function keys. Consult your Icom dealer or system operator for details concerning your transceivers programming. If the programmable function names are bracketed in the following explanations, t ...

  • Icom IC-F60V - page 15

    9 2 P ANEL DESCRIPTION 2 SCAN B ST ART/STOP KEY ➥ Push to start and cancel scanning operation. Scan resumes afte r a speci fi ed time period has passed when scan is cancelled except for this key . ➥ Push and hold this key for 1 sec. to indicate the scan group, then select the desired scan group using [CH Up]/[CH Down]. SCAN ADD/DEL (T AG) KEY ...

  • Icom IC-F60V - page 16

    10 2 P ANEL DESCRIPTION MONITOR KEY ➥ Mute and release the CTCSS (DTCS) or 2-tone squelch mute. Open any squelch/deactivate any mute while pushing and hold- ing this key . (LMR operation only) ➥ Activates one of (or two of) the following functions on each chan - nel independently: (PMR operation only) • Push and hold to un-mute the channel (a ...

  • Icom IC-F60V - page 17

    11 2 P ANEL DESCRIPTION 2 T ALK AROUND KEY Push to turn the talk around function ON and OFF . • The talk around function equalizes the transmit frequency to the re- ceive frequency for transceiver-to-transceiver communication. WIDE/NARROW KEY Push to toggle the IF bandwidth between wide and narrow . • The wide passband width can be selected fro ...

  • Icom IC-F60V - page 18

    12 2 P ANEL DESCRIPTION EMERGENCY KEYS Push and hold to transmit the emergency call. • The emergency call transmits with beeps; the display does not change. • The transceiver can transmit the emergency call silently or with the display changes depending on the pre-setting. Ask your dealer for de- tails. • If you want to cancel the emergency c ...

  • Icom IC-F60V - page 19

    13 2 P ANEL DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 COMP ANDER KEY Push to turn the compander function ON and OFF . The compander function reduces noise components from the trans- mitting audio to provide clearer communication. USER SET MODE KEY ➥ Push and hold to enter user set mode. • While in user set mode, push this k ...

  • Icom IC-F60V - page 20

    14 3 BASIC OPERA TION ■ T urning power ON q Rotate [VOL] to turn power ON. • When the opening vibration function is turned ON, the transceiver vibrates for 2 sec. Ask your dealer for details. w If the transceiver is programmed for a start up passcode, input digit codes as directed by your dealer . • The keys in the table below can be used for ...

  • Icom IC-F60V - page 21

    15 3 BASIC OPERA TION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ■ Call procedure When your system employs tone signalling (excluding CTCSS and DTCS), this call procedure may be necessary prior to voice trans- mission. The tone signalling employed may be a selective calling system which allows you to call speci fi c station(s) only and p ...

  • Icom IC-F60V - page 22

    16 3 BASIC OPERA TION ■ Receiving and transmitting NOTE: T ransmitting without an antenna may damage the trans- ceiver . See p. 2 for antenna attachment. Receiving: q Rotate [VOL] to turn power ON. w Push [CH Up] or [CH Down] to select a channel. e When receiving a call, adjust the audio output level to a comfort- able listening level. Transmitti ...

  • Icom IC-F60V - page 23

    17 3 BASIC OPERA TION 3 D Receiving note • Vibration function (Depends on the version) When the matched RX code signal is received, the transceiver may vibrate for a specified time period, depending on the pre-setting. Push any key or [PTT] to stop the vibration. NOTE: • The transceiver cannot stop the vibration suddenly after push- ing any key ...

  • Icom IC-F60V - page 24

    18 3 BASIC OPERA TION D TX code channel selection If the transceiver has [TX Code CH Select] assigned to it, the indi- cation can be toggled between the operating channel number (or name) and TX code channel number (or name). When the TX code channel number (or name) is displayed, [CH Up] or [CH Down] se- lects the TX code channel. USING [TX CODE C ...

  • Icom IC-F60V - page 25

    19 3 BASIC OPERA TION 3 e Push [TX Code CH Select] to select the desired digit to be edited. r Push [CH Up]/[CH Down] to select the desired digit. t Push [TX Code CH Select] to set. The digit to the right will blink automatically . y Repeat r and t to edit all allowable digits. u After editing, push [TX Code CH Select] to set. • Return to the sta ...

  • Icom IC-F60V - page 26

    20 3 BASIC OPERA TION ■ User set mode User set mode is accessed at power ON and allows you to set sel- dom-changed settings. Y ou can “ customize ” the transceiver opera- tion to suit your preferences and operating style. Entering the user set mode: q While pushing and holding [ ] and [ ], rotate [VOL] to power ON. • T urn power OFF in adva ...

  • Icom IC-F60V - page 27

    21 3 BASIC OPERA TION 3 ■ Emergency transmission When [Emergency] is pushed for the specified time period, an emergency signal is automatically transmitted. When [Emergency] is pushed for the specified time period, the DTMF emergency signal is transmitted once or repeatedly on the emergency channel. However , when no emergency channel is speci ? ...

  • Icom IC-F60V - page 28

    22 3 BASIC OPERA TION ■ Recording function (Depends on the version) The transceiver has a recording function that records the TX/RX voice messages. When the speci fi ed ID is received, the automatic recording function activates and records the voice message for a speci fi ed time period. Or , if the transceiver has [Playback/Rec] assigned to it ...

  • Icom IC-F60V - page 29

    23 3 BASIC OPERA TION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 e Release [PTT] to receive. • The RX voice message is recorded. r Push [Playback/Rec] again to stop recording. • “” stops blinking. • The recording operation automatically stops after the following: the recording memory is full, pushing any key but [PTT], or transmit ...

  • Icom IC-F60V - page 30

    24 4 BA TTER Y CHARGING ■ Caution R DANGER! Use and charge only specified Icom battery packs with Icom radios or Icom charger . Only Icom battery packs are tested and approved for use and charge with Icom radios or Icom charger . Using third-party or counterfeit battery packs or charger may cause smoke, fi re, or cause the battery to burst. D D ...

  • Icom IC-F60V - page 31

    25 4 BA TTERY CHARGING 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 R DANGER! NEVER solder the battery terminals or NEVER mod- ify the battery pack. This may cause heat generation, and the bat- tery may rupture, emit smoke or catch fi re. R DANGER! Use the battery only with the transceiver for which it is speci fi ed. Never use a battery wi ...

  • Icom IC-F60V - page 32

    26 4 BA TTERY CHARGING D D Charging caution R DANGER! NEVER charge the battery pack in areas with ex- tremely high temperatures, such as near fi res or stoves, inside a sun heated car , or in direct sunlight. In such environments, the safety/protection circuit in the battery will activate, causing the bat- tery to stop charging. W ARNING! DO NOT c ...

  • Icom IC-F60V - page 33

    27 4 BA TTERY CHARGING 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ■ Optional battery chargers ï Regular charging with the BC-152 q Attach the BC-152 to a fl at surface, such as a desk, if desired. w Connect the AC adapter (BC-147) as shown below. e Insert the battery pack with/without the transceiver into the charger . • The charge in ...

  • Icom IC-F60V - page 34

    28 4 BA TTERY CHARGING D For your convenience Eyelet USE a rubber band to secure the transceiv- er while charging, if desired. ! IC-F50V_F60V_0.qxd 07.8.6 10:36 AM Page 28 (1,1) ...

  • Icom IC-F60V - page 35

    29 4 BA TTERY CHARGING 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ï AD-100 installation The AD-100 CHARGER ADAPTER must be installed into the BC-1 19N or BC-121N before battery charging. ➥ Connect the AD-100 CHARGER ADAPTER and the BC-1 19N/BC- 121N as below , then install the AD-100 into the holder space of the BC-1 19N or BC-121N with ...

  • Icom IC-F60V - page 36

    30 4 BA TTERY CHARGING D Rapid charging with the BC-1 19N+AD-100 The optional BC-1 19N provides rapid charging of the optional Li- Ion battery pack. The following items are additionally required: • An AD-100 charger adapter • An AC adapter (may be supplied with BC-1 19N depending on ver- sion) or the DC power cable (OPC-515L/CP-17L). AC adapter ...

  • Icom IC-F60V - page 37

    31 4 BA TTERY CHARGING 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 D Rapid charging with the BC-121N+AD-100 The optional BC-121N allows up to 6 battery packs to be charged simultaneously . The following items are additionally required. • Six AD-100 charger adapter • An AC adapter (BC-157) or the DC power cable (OPC-656) MULTI-CHARGER AC ...

  • Icom IC-F60V - page 38

    32 5 BA TTER Y CASE ■ Optional battery case (BP-226) When using the optional battery case attached to the transceiver , install 5 × AA (LR6) size alkaline batteries as illustrated at right. The BP-226 is constructed to the IPX4 waterproof standard (IEC 60529, 2006). q Hook your fi nger under the latch, and open the cover in the direc - tion of ...

  • Icom IC-F60V - page 39

    33 5 BA TTERY CASE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 q w e BP-226 Latch Fig.1 Fig.2 Ribbon Fig.3 Gasket Ribbon ! IC-F50V_F60V_0.qxd 07.8.6 10:36 AM Page 33 (1,1) ...

  • Icom IC-F60V - page 40

    34 6 SPEAKER-MICROPHONE ■ Optional HM-168 description NEVER immerse the connector in water . If the connector becomes wet, be sure to dry it BEFORE attaching it to the transceiver . NOTE: The microphone is located at the top of the speaker-mi- crophone, as shown in the diagram above. T o maximize the readability of your transmitted signal (voice) ...

  • Icom IC-F60V - page 41

    35 6 SPEAKER-MICROPHONE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 ■ Attachment Attach the connector of the speaker-microphone into the [SP MIC] jack on the transceiver and tighten the screw . IMPORT ANT : KEEP the [SP MIC] jack cover attached to the transceiver when the speaker-microphone is not in use. (p. 3) W ater will not get into th ...

  • Icom IC-F60V - page 42

    36 7 SWIVEL BEL T CLIP ■ Optional MB-86 contents Qty . q Belt clip ………………………………………………………………… 1 w Base clip ……………………………………………………………… 1 e Screws ………………………………………………………………… 2 ■ Attaching q Attach the ba ...

  • Icom IC-F60V - page 43

    37 7 SWIVEL BEL T CLIP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 e Once the transceiver is locked in place, it will swivel 360 de- grees. ■ Detaching T urn the transceiver upside down, and pull out from the belt clip. Then detach the base clip from the back of the transceiver . CAUTION! HOLD THE TRANSCEIVER TIGHTL Y WHEN A TT ACHING OR D ...

  • Icom IC-F60V - page 44

    38 8 OPTIONS D D BA TTER Y P ACK/CASE • BP-226 BA TTERY CASE Battery case for 5 × AA (LR6) alkaline cells. • BP-227 L i - I on BA TTERY P ACK 7.2 V/1700 mAh Li-Ion battery pack. The same as supplied with the transceiver . BP-227 must be charged with the optional BC- 152/BC-1 19N/BC-121N. D D CHARGERS • BC-152 DESKTOP CHARGER + BC-147 AC ADAP ...

  • Icom IC-F60V - page 45

    39 8 OPTIONS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 D D DC CABLES • CP-17L CIGARETTE LIGHTER CABLE Allows charging of the battery pack through a 12 V cigarette lighter socket. (For BC-152/BC-1 19N) • OPC-515L/OPC-656 DC POWER CABLES Allows charging of the battery pack using a 13.8 V power source instead of the AC adapter . OPC-515L ...

  • Icom IC-F60V - page 46

    40 8 OPTIONS ï About VS-1SC VOX / PTT CASE The VS-1SC is a VOX/PTT unit for Icom handheld transceivers, and allows you hands-free operation. An optional headset (HS-94, etc.) is required for operation. • The VOX (V oice Operated T ransmission) function starts transmission without pushing PTT switch when you speak into the microphone; then, autom ...

  • Icom IC-F60V - page 47

    41 8 OPTIONS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 VOX gain and delay adjustment q Attach the connector of the VS-1SC into the [SP/MIC] connector on the transceiver and tighten the screw . • T oggle the toggle switch to [VOX]. w Enter user set mode. (pgs. 13, 20) e Push [P0] several times to select “ VOX Gain ” or “ VOX Delay . ...

  • Icom IC-F60V - page 48

    1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan A-6604H-1EX Printed in Japan © 2007 Icom Inc. Printed on recycled paper with soy ink. ! IC-F50V_F60V_0.qxd 07.8.6 10:36 AM Page 42 (1,1) ...

Manufacturer Icom Category Marine Radio

Documents that we receive from a manufacturer of a Icom IC-F60V can be divided into several groups. They are, among others:
- Icom technical drawings
- IC-F60V manuals
- Icom product data sheets
- information booklets
- or energy labels Icom IC-F60V
All of them are important, but the most important information from the point of view of use of the device are in the user manual Icom IC-F60V.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Icom IC-F60V, service manual, brief instructions and user manuals Icom IC-F60V. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Icom IC-F60V.

Similar manuals

A complete manual for the device Icom IC-F60V, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Icom IC-F60V by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Icom IC-F60V.

A complete Icom manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Icom IC-F60V - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Icom IC-F60V, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Icom IC-F60V, that we can find in the current document
3. Tips how to use the basic functions of the device Icom IC-F60V - which should help us in our first steps of using Icom IC-F60V
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Icom IC-F60V
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Icom IC-F60V in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Icom IC-F60V?

Use the form below

If you did not solve your problem by using a manual Icom IC-F60V, ask a question using the form below. If a user had a similar problem with Icom IC-F60V it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)