English dropdown-ico

Manual ARC Inverter Power Sources

24 pages 0.2 mb
Download

Go to site of 24

Summary
  • ARC Inverter Power Sources - page 1

    86(5,1675 8&7,210$18 $/ ...

  • ARC Inverter Power Sources - page 2

    ENGLISH 3 ESPAÑOL 9 FRANCAIS 16 TECHNICAL TABLES TABLAS TECNICAS 22 TABLES TECHNIQUES SPARE PARTS LIST LISTA DE PIEZAS DE REPUESTO 23 LISTE DES PIECES DE RECHANGE ...

  • ARC Inverter Power Sources - page 3

    ENGLISH INTRODUCTION Congratulations for your choice. Our products have been designed, manufactured and tested to comply with the latest European Community requirements. The arc welding power sy stem, if used correctly, can be operated in very safe conditions while if the prescribed safety norms a re not observed it could cause serious damages to p ...

  • ARC Inverter Power Sources - page 4

    METHODS OF REDUCING EMISSIONS Mains supply Welding equipment should be connected to the mains supply according to the manufacturers recommendations. If interference occurs, it may be necessary to take additional precautions such as filtering of the mains supply. Consideration should be given to shielding the supply cable of permanently installed w ...

  • ARC Inverter Power Sources - page 5

    1.2.5 Electric shock All electric shocks are potentially fatal and therefore live wires and/or parts should never be touched. Insulation must be kept from the piece to be welded and from the ground by wearing insulation gloves and clothing. Garments such as gloves, shoes, hats, clothings and body must be kept dry at all times and it is to be avoide ...

  • ARC Inverter Power Sources - page 6

    SECTION 3 --- INSTALLA TION PROCEDURE 3.1 UNPACKING AND SETUP Unpack the unit and carefully inspect it for shipping damages. Any claims for damages which may have occurred in transit must be filed by the purchaser with the carrier and in order not to loose any right to file such a claim no clean receipt should be signed but a mention should be made ...

  • ARC Inverter Power Sources - page 7

    All possible precautions must be taken in order to avoid stray current. Connect gas pipe to pressure reducer output connected to an ARGON cylinder. Regulate gas flow adjusting the regulation knob on the torch handle. Inside the torch handle a valve allows the gas flow to be shut. Use a 2% thoriated tungsten electrode having a diameter chosen accord ...

  • ARC Inverter Power Sources - page 8

    - Special saving circuit that, if the generator is not used within 30 s from ignition, disables all function and reduces power consumption to only 25 W (no greater than a light bulb’s), thus eliminating any undue internal heating, increasing generator li fe and, more important, saving 1 kWh every four hours of operation. Of course, as soon as the ...

  • ARC Inverter Power Sources - page 9

    ESPAÑOL INTRODUCCIÓN Felicitaciones por su elección! Nuestros productos en el campo de la tecnología a INVERTER responden a los dictámenes de las vigentes normas europeas. El sistema calidad asegura la producción de soldadoras de confianza y que duran mucho. En efecto los productos estan asegurados para 24 meses. Estamos convencidos que si se ...

  • ARC Inverter Power Sources - page 10

    h) Se pueden resolver algunos problemas si se cumplen las operaciones de soldadura o de corte cuando las otras maquinarias no trabajan. Las dimensiones del lugar de trabajo en consideración procede de la estructura del edificio y de las actividades en curso. METODOS PARA LA REDUCCIÓN DE LA S EMISIONES Alimentación El aparato de soldadura o corte ...

  • ARC Inverter Power Sources - page 11

    SECCIÓN 1 --- SEGURIDAD 1.1 INTRODUCIÓN Los procedimentos de soldadura con arco desarroladosen el curso de los años pueden ser empleados con un margen alto de seguridad, siempre que se observentodas las reglas que aconsejan el buen sentido y los consejos de los fabricantes. Por lo tanto es imperativo que los directores responsables de la segurid ...

  • ARC Inverter Power Sources - page 12

    1.2.6 Pacemaker La persona que lleva un aparato electrónico vital como el "pacemaker", tiene que consultar a su mdico antes de acercarse a operaciones de soldadura al arco, de corte, de eliminaci de las hendiduras o de soldadura a puntos para asegurar si campos eléctricos producidos por elevadas corrientes pueden influir en el funcionam ...

  • ARC Inverter Power Sources - page 13

    adquirente directamente al transportador. Y por no perder el derecho de presentar otra vez una reclamación, después de haber sacado el generador del embalaje. No otorgar ningún recibo en blanco pero indicar siempre la reserva de presentar eventualmente después de alguno di as una reclamación por los daños del transporte observados sólo despu ...

  • ARC Inverter Power Sources - page 14

    No tocar la parte bajo tensión No tocar los bornes de salida de soldadura cuando el aparato está en función No tocar a la vez la antorcha o la pinza portaeléctrodo y el borne de masa. Regular la corriente según el diametro del eléctrod o, la posicíón de soldadura y el modelo de juntura que tiene que ser efectuada. Cuando el trabajo es termi ...

  • ARC Inverter Power Sources - page 15

    4. Inicio de la fase de descenso de la corriente. 5. Apagamiento del arco cuando está en un valor cercano a cero. 6. Inicio de la fase de Post-Gas. Si se ha programado un tiempo de descenso de la corriente relativamente largo y no se quiere esperar el apagamiento automático del arco, es posible dar un ulterior impulso e interrumpir en cualquier m ...

  • ARC Inverter Power Sources - page 16

    FRANCAIS SOMMAIRE INSTRUCTIONS POUR LA COMPA TIBILITE ELECTROMAGNETIQUE METHODES DE REDUCTION DES EMISSIONS SECTION 1 --- SECURITE 1.1 INTRODUCTION 1.2 PRECAUTIONS GENERA LES SECTION 2 --- DESCRIPTION GENERALE ET CA RACTERISTIQUES DU PRODUIT 2.1 INTRODUCTION 2.2 DESCRIPTION DU SYSTEME 2.5 EXPLICATION DES SYMBOLES TECHNIQUES 2.6 DISPOSITIFS DE PROTE ...

  • ARC Inverter Power Sources - page 17

    Le blindage doit être connecté au bloc d'alimentation du poste de soudage afin de maintenir un bon contact entre la gaine et le boîtier du bloc. ENTRETIEN DE L'APPAREIL DE SOUDAGE L'appareil de soudage doit être régulièrement entretenu selon les recommandations du fabricant. Tous les capots et portes d'accès et d'ent ...

  • ARC Inverter Power Sources - page 18

    Les gants, les chaussures, les casques, les vêtements et le corps doivent toujours être secs et il faut éviter de travailler da ns des zones humides ou mouillées. Ne jamais toucher ou tenir la pièce à souder avec la main ; si l'on ressent la plus petite commotion électrique, il faut arrêter de souder immédiatement ; l'appareil ne ...

  • ARC Inverter Power Sources - page 19

    (figure 2) SECTION 3 --- PROCEDURE D'INSTALLA TION 3.1 DEBALLAGE ET MONTAGE Déballer l'appareil et contrôler soigneusement l'absence de détérioration. Les réclamations relatives à des dommages de transport doivent être adressées par l'acheteur au transporteur. Pour ne pas perdre le droit à un recours, il ne faut pas ava ...

  • ARC Inverter Power Sources - page 20

    Régler le courant selon le diamètre de l'électrode, la position de soudage et le type de joint à souder. Lorsque le soudage est terminé, ne jamais oublier de mettre le commutateur sur arrêt et d'enlever l'électrode de la pince. 4.3 SOUDAGE TIG Ce bloc d'alimentation convient pour le soudage TIG de l'acier inoxydable, ...

  • ARC Inverter Power Sources - page 21

    8. Extinction de l’arc à une valeur très proche du zéro. 9. Début de la phase de Post Gaz Si nous avons programmé un temps de descente du courant relativement long et nous ne voulons pas attendre l’extinction automatique de l’arc, il est possible de donner une autre impulsion et d’interrompre, à n’importe quel moment, le soudage. Si ...

  • ARC Inverter Power Sources - page 22

    Duty cycle 35% 100 A Main voltage 230 VAC 115 VAC Frequency 50/60 Hz Cos φ 0.99 Efficiency 0.85 Current range 5 – 100 A Off load voltage 80 V Output current 60% 80 A Output current 35% 100 A A bsorbed power 60% 2.4 KVA A bsorbed power 35% 3.1 KVA Main current 60% 11.7 A 23.4 A Main current 35% 15 A 30.2 A Protection class IP 21 Insulation class ...

  • ARC Inverter Power Sources - page 23

    SPARE PARTS LIST - LISTA DE PIEZAS DE REPUESTO - LISTE DES PIECES DE RECHANGE DUTY CYCLE 35% - 40% DESCRIPTION CODE POINT OF REFERENCE Varistor 275 V E1700275 VR1 Input bridge E3100060 P1 Electr. Capacitor 470uF 400V E4456470 C1/C2/C3 Start resistor 2.2 OHM E2620022 R1 Start relay E8104061 RL1 1001 PWM hybrid E9220PWM IB1 501 FBA hybrid E91FBA51 IB ...

  • ARC Inverter Power Sources - page 24

     $UF2QHLVDGLYLVLRQRI$&(,QWHUQDWLRQDO ,QGHSHQGHQFH'U  7 DXQWRQ0$  3K )D[ ZZZ DUFZHOGVDIHFRP ...

Manufacturer ARC Category Power Supply

Documents that we receive from a manufacturer of a ARC Inverter Power Sources can be divided into several groups. They are, among others:
- ARC technical drawings
- Inverter Power Sources manuals
- ARC product data sheets
- information booklets
- or energy labels ARC Inverter Power Sources
All of them are important, but the most important information from the point of view of use of the device are in the user manual ARC Inverter Power Sources.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals ARC Inverter Power Sources, service manual, brief instructions and user manuals ARC Inverter Power Sources. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product ARC Inverter Power Sources.

Similar manuals

A complete manual for the device ARC Inverter Power Sources, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use ARC Inverter Power Sources by users. Manuals are usually written by a technical writer, but in a language understandable to all users of ARC Inverter Power Sources.

A complete ARC manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual ARC Inverter Power Sources - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the ARC Inverter Power Sources, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the ARC Inverter Power Sources, that we can find in the current document
3. Tips how to use the basic functions of the device ARC Inverter Power Sources - which should help us in our first steps of using ARC Inverter Power Sources
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with ARC Inverter Power Sources
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of ARC Inverter Power Sources in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning ARC Inverter Power Sources?

Use the form below

If you did not solve your problem by using a manual ARC Inverter Power Sources, ask a question using the form below. If a user had a similar problem with ARC Inverter Power Sources it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)