-
Toshiba IK-TF9C - page 1
For Customer Use Enter below the Serial # which is located on the bottom of the cabinet. Retain this information f or future reference. Model #: IK-TF9C Serial #: 3 CCD CAMERA IK-TF9C INSTR UCTION MANU AL FCC NOTICE This equipment has been tested and f ound to comply with the limits for a Class A digital de vice, pursu- ant to P ar t 15 of the FCC ...
-
Toshiba IK-TF9C - page 2
2 SAFETY PRECA UTIONS Safety icons This manual contains saf ety instructions that must be observed in order to av oid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions ha v e been classified according to the seriousness of the risk, and the icons highlight these instructions a ...
-
Toshiba IK-TF9C - page 3
3 Note the follo wing instructions when installing. • Do not cov er the product by an y material. • Do not put the product on an Inflammable material such as carpet or blanket. • Do not put the product in a narrow space , since the heat generated from the product ma y be difficult to emanate. If you do not f ollo w the above , the heat genera ...
-
Toshiba IK-TF9C - page 4
4 1. CAUTIONS ON USE AND INST ALLA TION ..... 5 2. COMPONENTS ................................................ 5 3. NAMES AND FUNCTIONS .............................. 6 4. CONNECTION .................................................. 7 4. 1 Standard Connection ................................ 7 4. 2 Cautions on Connection .......................... ...
-
Toshiba IK-TF9C - page 5
5 1. CA UTIONS ON USE AND INST ALLA TION • Carefully handle the units. Do not drop, or give a strong shock or vibration to the camera. This may cause problems . T reat the camera cables carefully to prevent cable prob- lems, such as cable breakdown and loosened con- nections. • Do not shoot intense light. If there is an intense light at a locat ...
-
Toshiba IK-TF9C - page 6
6 3. NAMES AND FUNCTIONS 1 Prism faceplate The protection cap is attached on the lens mount portion. After remo ving the cap , mount the lens. Be careful not to scratch or touch the optical area. 2 DISP button Used when s witching the display . 3 PA GE button Used when s witching to the menu and when selecting the menus . 4 MENU UP button Select th ...
-
Toshiba IK-TF9C - page 7
7 4. CONNECTION 4. 1 Standar d Connection IK-TF9C DC IN 12V Lens (not included) Cable (not included) Frame grabber board, image process equipment etc. Monitor DC power supply (not included) Less than 4 mm DC IN 12V Connector used: HR10A-7P-4PB (HIROSE electronics Co. Ltd) or equivalent. DIGITAL Function I/O 1 +12V 1 2 +12V 2 3 GND 3 4 GND 4 5 6 7 8 ...
-
Toshiba IK-TF9C - page 8
8 5. OPERA TION 1 Refer to the item " 4. CONNECTION", connect each equipment correctly . 2 Tu rn on the connected equipment and the power source of the camera. 3 P oint the lens at the object, oper ate the lens iris adjustment, focus adjustment, etc.. 4 Refer to the item "5.1 White Balance", oper ate the adjustment. 5 Refer to t ...
-
Toshiba IK-TF9C - page 9
9 2 MANU (Manual white balance) • Set the MODE to MANU on the WHT BAL menu. (Ref er to the item "7.2 (3) WHT BAL (white balance)".) •S hoot a known white object, adjust the white balance adjusting the le vels of R GAIN and B GAIN on the menu, confirming with a monitor etc. (Ref er to the item "7.2 (3) (3.2) Changing each setting ...
-
Toshiba IK-TF9C - page 10
10 Process Electronic shutter 6. ITEMS CONTROLLED BY USING ON SCREEN DISPLA Y MODE E. TRG MANU speed Syncro. scan. Partial read Tr igger (1P SNR/SR) Tr igger (PW SNR/SR) 1P e xposure time MODE MANU MODE Color temperature MANUAL R GAIN MANUAL B GAIN GAMMA Master pedestal R pedestal B pedestal Shading correction mode Manual shading correction Baud ra ...
-
Toshiba IK-TF9C - page 11
11 7. MODE SETTING BY ON SCREEN DISPLA Y Va r ious settings can be controlled on the unit by using the on screen menu displa yed on the monitor . The contents once set are memorized ev en if the pow er source is turned off, so it is unnecessary to set again when using the unit next time. When the setting is performed, select the menu of the item to ...
-
Toshiba IK-TF9C - page 12
12 7. 2 Menus • Select the menu to change the setting b y referring the item "7.1 Using the Menus".) • When the [MENU UP], [MENU DO WN] buttons are pushed, the " → " on the screen mov es up and down. Move the " → " to the item to change. Note: When performing the mode setting in the men u display while selectin ...
-
Toshiba IK-TF9C - page 13
13 (a) Changing the shutter speed 1 Set the " → " to MANU b y pushing [MENU UP], [MENU DO WN] buttons. 2 Set the shutter speed by pushing [D A T A UP], [DA T A DO WN] buttons . (b) Partial scanning setting 1 Set the " → " to P ART by pushing [MENU UP], [MENU DO WN] b uttons. 2 Select either OFF/30fps/40fps/E.30fps/E.40fps b ...
-
Toshiba IK-TF9C - page 14
14 (1. 2) Changing each setting in SS (synchro. scan) mode (a) Changing the shutter speed setting 1 Set the " → " to SS by pushing [MENU UP], [MENU DO WN] buttons . 2 Select the shutter speed by pushing [D A T A UP], [DA T A DOWN] b uttons. (b) Partial scanning setting 1 Set the " → " to P AR T by pushing [MENU UP], [MENU DO ...
-
Toshiba IK-TF9C - page 15
15 (1. 3) Changing each setting in E.TRG mode The E.TRG has f our modes; 1P SNR, 1P SR, PW SNR, PW SR. First set the " → " to MODE and select E. TRG, then set the " → " to E.TRG and select the desired E.TRG mode. (1. 3. 1) Changing each setting in 1P SNR mode (a) Changing the polarity of inputting trigger pulse setting 1 Set ...
-
Toshiba IK-TF9C - page 16
16 (1. 3. 2) Changing each setting in 1P SR mode (a) Changing the polarity of inputting trigger pulse setting 1 Set the " → " to TRG.P by pushing [MENU UP], [MENU DO WN] buttons . 2 Select either , by pushing [D A T A UP], [DA T A DOWN] b uttons. (b) Changing 1P SR exposure time setting 1 Set the " → " to EXP . b y pushing [ ...
-
Toshiba IK-TF9C - page 17
17 (1. 3. 3) Changing each setting in PW SNR mode (a) Changing the polarity of inputting trigger pulse setting 1 Set the " → " to TRG.P by pushing [MENU UP], [MENU DOWN] b uttons. 2 Select either , by pushing [D A T A UP], [DA T A DOWN] b uttons. (b) Changing the partial scanning setting 1 Set the " → " to P ART by pushing [ ...
-
Toshiba IK-TF9C - page 18
18 (1. 3. 4) Changing each setting in PW SR mode -- SHUTTER -- MODE E.TRG E.TRG PW SR TRG.P PART OFF <MODE = E.TRG E.TRG = PW SR> • Partial scanning switch OFF/30fps/40fps/E.30fps/E.40fps Input trigger pulse : positive polarity Input trigger pulse : negative polarity 1P SNR, 1P SR, PW SNR, PW SR • Input trigger pulse setting at PW SNR and ...
-
Toshiba IK-TF9C - page 19
19 ( 2 ) GAIN (Video gain) When the image is dark even if the lens iris is open, change the gain (video gain) to get the proper video le vel. F or the gain adjustment of the unit, MANU (Manual) and OFF (0dB) modes are pro vided. 1 MANU (Manual gain) Gain adjustment is performed on the GAIN menu. The adjustment range is from 0dB to 18dB in 1dB steps ...
-
Toshiba IK-TF9C - page 20
20 ( 3 ) WHT B AL (White balance) WHT BAL has two modes; A WB, MANU. Set the " → " to MODE, push the [D A T A UP], [DA T A DOWN], and select mode among A WB, MANU . (3. 1) Changing each setting in AWB (A utomatic White Balance) mode (a) Changing color temperature setting 1 Set the " → " to C.TEMP b y pushing [MENU UP], [MENU ...
-
Toshiba IK-TF9C - page 21
21 ( 4 ) PROCESS • Gamma Correction (GAMMA) Select either OFF or ON of Gamma Correction. • Master P edestal (M. PED) Set the P edestal le vel of each RGB . •R Pedestal (R. PED) Set the P edestal le vel of Red. •B Pedestal (B. PED) Set the P edestal le vel of Blue. • Shading Correction (SHAD .) Due to the lens used or the environmental con ...
-
Toshiba IK-TF9C - page 22
22 • Serial baud rate 9600, 19200 -- OPTION -- BAUD RATE 9600 Move up down By pushing MENU UP, DOWN Set by pushing DATA UP, DOWN ( 6 ) Setting to factory setting status All the settings can be returned to the factory default status (preset status). (1) If characters are displa yed on the screen, press the [DISP] b utton to disable the char acter ...
-
Toshiba IK-TF9C - page 23
23 7. 3 Synchr o. Scan Operation The shutter speed can be set by the doub le horizontal scanning period (2H) or by the frame . ( 1 ) Setting by 2H 2H/1592H ~ 1590H/1592H (2H/1060H ~ 1058H/1060H at 30fps and E.30fps of Partial Scanning, 2H/774H ~ 772H/774H at 40fps and E.40fps of P artial Scanning) stands for the setting by the 2H and the shutter sp ...
-
Toshiba IK-TF9C - page 24
24 7. 4E . TRG (External trigger) Charge begins to accumulate after the trigger input to CC1 of the DIGIT AL terminal, and 1 frame images are output. There are f our modes: 1P SNR, 1P SR, PW SNR, PW SR. ( 1 ) 1P SNR (1 Pulse T rig g er Sync Non Reset) Charge begins to accumulate after the trigger input to CC1 of the DIGIT AL terminal, and 1 frame i ...
-
Toshiba IK-TF9C - page 25
25 About 1 µ s Exposure completion 0 to 2H* 3 Exposure period* 2 Tr igger* 1 Negative polarity mode P ositive polarity mode (Internal VD) RGB data (video interval image) FV AL LV AL, DVA L 58H ( Pa r tial scanning OFF ) 56H ( Pa r tial scanning 30fps) 78H ( Pa r tial scanning 40fps) ( 2 ) 1P SR (1 Pulse T rig g er Sync Reset) Charge begins to accu ...
-
Toshiba IK-TF9C - page 26
26 ( 3 ) PW SNR (Pulse width trig g er SYNC-NON RESET) The trigger input to CC1 of the DIGIT AL terminal dev elops 1 frame images. (3. 1) Pulse Width T rigger SYNC-NON RESET Picture Output Timing *1: Externally input signal *2: Exposure time = T rigger pulse width + 6 µ s (V alid trigger pulse width is 2 µ s or greater f or e xternal tr igger shu ...
-
Toshiba IK-TF9C - page 27
27 ( 4 ) PW SR (Pulse width trig g er SYNC-RESET) The trigger input to the CC1 of the DIGIT AL terminal dev elops 1 frame images. (4. 1) 1 Pulse Width T rig ger SYNC-RESET Picture Output Timing *1: Externally input signal *2: Exposure time = T rigger pulse width + 6 µ s (V alid trigger pulse width is 2 µ s or greater f or e xternal trigger shutte ...
-
Toshiba IK-TF9C - page 28
28 7. 5P artial Read ( 1 ) Partial Scanning OFF (All pixels scanning) In this mode, all pix els independent signal from the DIGIT AL connector is output each 1/20 second (Line order output). ( 2 ) Partial Scanning ON In this mode, the pix el signal of the v er tical center portion from the DIGIT AL connector is output. In the E.30fps or E.40fps mod ...
-
Toshiba IK-TF9C - page 29
29 8. OUTPUT W A VEFORM TIMING CHART ( 1 ) Horizontal Output W avef orm Timing Chart 2048 2048 1 LVAL、 DVAL RGB data Horizontal blanking interval 492 clk (6.08 µ s) Output video interval 2048 clk (25.3 µ s) One horizontal scan interval 2540 clk (31.4 µ s) CLK=12.36nsec (80.8736MHz) Pixel Clock LVAL、 DVAL FV AL RGB data (CCD READOUT) Video ou ...
-
Toshiba IK-TF9C - page 30
30 9. SPECIFICA TIONS Po wer supply Po wer consumption Pick-up system Image sensor Scanning System Video output pixels Pixel cloc k frequency Sync signal frequency Sync system Sensitivity Minimum illumination Lens mount Ambient temperature Ambient humidity W eight External dimension White balance Gain Par tial scanning Output signal Sync signal out ...
-
Toshiba IK-TF9C - page 31
31 11. BEFORE MAKING A SER VICE CALL 10. EXTERNAL APPEARANCE DIA GRAM DISP PAGE DC IN 12V MENU DATA (AWB) 44 [1.73] 44 [1.73] 22 [0.87] 5 [0.20] 26 [1.02] 6.3 [0.25] 78 [3.07] 56 [2.20] 5 [0.20] 26 [1.02] 25 [0.98] 25 [0.98] 25 [0.98] 12 [0.47] 34 [1.34] 8.2 [0.32] 26 [1.02] Unit : mm [inch] * inch=mm/25.4 2-M3 Depth 3 4-M2 Depth 3 4-M3 Depth 3 2-M ...
-
Toshiba IK-TF9C - page 32
LIMITED W ARRANTY T OSHIB A CCD CAMERA The Imaging Systems Division of T oshiba Amer ica Information Systems, Inc. ("ISD") makes the follo wing limited w arranties. These limited w arranties e xtend to the Original End-User ("Y our[r]"). Limited One (1) Y ear Warranty of Labor and P arts ISD warrants this product and parts again ...
Do you have a question concerning Toshiba IK-TF9C?
Use the form below
If you did not solve your problem by using a manual Toshiba IK-TF9C, ask a question using the form below. If a user had a similar problem with Toshiba IK-TF9C it is likely that he will want to share the way to solve it.