English dropdown-ico

Manual Jensen XA4150

12 pages 0.19 mb
Download

Go to site of 12

Summary
  • Jensen XA4150 - page 1

    How to Install and Operate the XA4150 Amplifier ® Contents T echnical Assistance For technical assistance with the operation or installation of the XA4150, call 1-800-323-0221. Welcome! What you're holding in your hands is no ordinary owner's manual. We've tried to make the instructions in this book clear and easy to follow . For yo ...

  • Jensen XA4150 - page 2

    2 ® XA4150 Amplifier Location The XA4150 amplifier’s compact design allows greater flexibility in mounting. It can be mounted under a seat or in the trunk. When selecting a location, remember that amplifiers generate heat. Select a location where air can circulate around the amplifier . Do not cover the XA4150 with carpets or enclose it behind i ...

  • Jensen XA4150 - page 3

    3 ® XA4150 Supplies and T ools Needed Supplies: • Speaker wire (12 gauge for subwoofers, 16-18 gauge for other speakers) • Sheet metal type screws for mounting amplifier • Electrical tape • Solderless crimp connectors • 1/2" thick plywood or particle board to mount amplifier on T ools: • Flat and Phillips screwdrivers • Wire cut ...

  • Jensen XA4150 - page 4

    4 ® XA4150 Wiring Power and Outputs Remote T erminal (RMT +12V) Power T erminal (BA TT +12V) Connect directly to the vehicle battery+ terminal with 8 gauge wire (minimum). Ground T erminal (GND) Connect to a good chassis ground. The ground connection should be to clean, unpainted metal to provide a good electrical connection. Connect the radio pow ...

  • Jensen XA4150 - page 5

    5 ® XA4150 Inputs and Contr ols Input Wiring Important Use only the low level or high level input, do not use both at one time. Low Level Input Use a pair of shielded stereo audio cables with RCA type jacks. Most trunk-mount amplifier installations require 20-foot RCA cables. Most under-seat and pickup truck installations use 12-foot cables. Conne ...

  • Jensen XA4150 - page 6

    6 ® XA4150 Adjust the crossover to accommodate your chosen installation method. Use LPF and HPF to adjust from 50 to 250Hz. When using your Jensen amplifier to run a subwoofer and two full- range speakers (known as T ri-mode or three channel operation) you will need to purchase separate high and low pass crossovers from your local retailer . A pai ...

  • Jensen XA4150 - page 7

    7 ® XA4150 Speaker Wiring The XA4150 amplifier has inputs and outputs for four channels 2 Subwoofers/Bridged Mono 4 Speakers A-CH B-CH C-CH D-CH + – – + + – – + RCA Cables 2/4 Ω 2/4 Ω 2/4 Ω 2/4 Ω OFF ON LPF FULL HPF BASS-BOOST OFF ON BASS-BOOST X-OVER LPF FULL HPF X-OVER CH 1/2 CH 3/4 4CH 3CH 2CH MODE A-CH B-CH C-CH D-CH + – – ...

  • Jensen XA4150 - page 8

    8 ® XA4150 4 Speakers + 2 Subwoofers 2 Speakers + Bridged Subwoofer Important When running a subwoofer and two full-range speakers together (T ri-mode operation), high and low pass filters must be used. Failure to install these filters will damage your amp and/ or speakers. A-CH B-CH C-CH D-CH + – – + + – – + RCA Cables 4 Ω 4 Ω 4 Ω 4 ...

  • Jensen XA4150 - page 9

    9 ® XA4150 T est Power Wiring 1. T urn on the receiver but do not turn up the volume. The amplifier power light should come on. If not, check the RMT and +12V wires. 2. T urn up the receiver volume slightly . All speakers should operate. If not, check wiring connections at amplifier and speakers. ✓ T esting T est Speaker Connections These tests ...

  • Jensen XA4150 - page 10

    10 ® XA4150 Professional Tip Crimp Connections Purchase crimp connectors and crimping tool. Connectors are color coded. 1. Strip 1/4 inch (6mm) of insulation from both wires. 2. Insert into connector . 3. Crimp tightly . Y ou can make permanent splices (using butt connectors) or select connectors that can be removed and reinstalled. 3 2 1 Strip wi ...

  • Jensen XA4150 - page 11

    11 ® XA4150 T r oubleshooting Problem Possible Cause Corrective Action Amplifier does not operate (power LED not on) when vehicle and radio are on Radio volume needs to be turned up too high for amp to work Radio volume is too sensitive Sound from only one speaker Sound distorted Blows fuses Alternator whine in outputs (vehicle ignition noise) Lou ...

  • Jensen XA4150 - page 12

    Specifications XA4150 Amplifier Power output @ 14.4 VDC, 20-20 kHz ............ (4 ohms) 75 W atts per channel RMS, < 00.08% THD (2 ohms) 100 W atts per channel RMS, < 00.1% THD (4 ohms) bridged 200 W atts per channel RMS, < 00.1% THD Frequency Response ....................................................................................... ...

Manufacturer Jensen Category Car Amplifier

Documents that we receive from a manufacturer of a Jensen XA4150 can be divided into several groups. They are, among others:
- Jensen technical drawings
- XA4150 manuals
- Jensen product data sheets
- information booklets
- or energy labels Jensen XA4150
All of them are important, but the most important information from the point of view of use of the device are in the user manual Jensen XA4150.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Jensen XA4150, service manual, brief instructions and user manuals Jensen XA4150. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Jensen XA4150.

Similar manuals

A complete manual for the device Jensen XA4150, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Jensen XA4150 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Jensen XA4150.

A complete Jensen manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Jensen XA4150 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Jensen XA4150, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Jensen XA4150, that we can find in the current document
3. Tips how to use the basic functions of the device Jensen XA4150 - which should help us in our first steps of using Jensen XA4150
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Jensen XA4150
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Jensen XA4150 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Jensen XA4150?

Use the form below

If you did not solve your problem by using a manual Jensen XA4150, ask a question using the form below. If a user had a similar problem with Jensen XA4150 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)