-
CDA SK450 - page 1
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu SK450 Single Ecoclean Oven Manual for Installation, Use and Maintenance ...
-
CDA SK450 - page 2
2 Important This appliance must only be used for the purpose for which it is intended, i.e. domestic cooking, defrosting and reheating foods. Any other use could be dangerous and may lead to premature failure of the appliance. The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this produ ...
-
CDA SK450 - page 3
3 CE Declarations of Conformity: This oven has been designed, constructed and marketed in compliance with safety requirements of EEC Directive 2006/95/EEC (L ow voltage) and requirements of EMC Directive 2004/108/EEC. This appliance has been manufactured to the strictest standards and complies with all applicable legislation, including Electrical s ...
-
CDA SK450 - page 4
4 Important • R ead the user instructions carefully before using the oven for the first time. • Follow the instructions for first use of the oven. • Clean the oven regularly . • R emove spills as soon as they occur . • Always use oven gloves when removing shelves and trays from the ovens. • Do not allow children near the oven when in ...
-
CDA SK450 - page 5
5 • Do not use abrasive cleaners or powders that will scratch the surface of the enamel. • Do not attempt to repair the internal workings of your oven. Using the T ouch Controls The touch controls should be used with the flat of your finger , rather than the fingertip. fig. 1 ...
-
CDA SK450 - page 6
6 The Control P anel A B C D E F G H I J K L M A: Oven light B: Conventional oven C: W arming oven D: Half grill E: Full grill F: Fanned grill G: Fan assisted oven H: Fan oven I: On/O and key lock J: Rapid preheat K: Oven clean L: Stop M: Start fig. 2 ...
-
CDA SK450 - page 7
7 N O P Q R S T U V W X Y Z N: Fan oven + lower heat O: Defrost P: Auto recipe Q: Confirm R: Scroll downward / Reduce power S: Scroll upward / Increase power T : Digital display U: Timer function V: Timer - cooking time W: Timer - end time X: Minute minder Y : Decrease settings Z: Increase settings ...
-
CDA SK450 - page 8
8 Before First Use When the oven is connected to the electrical supply for the first time, the display will ask you to select your language: Use the buttons to select the language you want, use the “ok” button to confirm your choice. The oven will remember your language preference, even after future power outages. After setting the language, ...
-
CDA SK450 - page 9
9 General Settings & Use Clock T o set the clock, touch the “Timer function” key for at least 3 seconds, the clock will show “00:00” with the separator dots flashing. Use the “+” and “-” keys to set the correct time: Five seconds after selecting the time the dots will stop flashing and the time will be set. K ey lock This appl ...
-
CDA SK450 - page 10
10 T o turn the oven on T ouch the “On/O ” key briefly , it gives one short beep followed immediately by a long one, the word ”ON” appears on the display for appro ximately one minute. T o turn the oven o T ouch the “On/O ” key briefly , it gives one long beep, the word ”OFF” appears briefly on the display . While the wo ...
-
CDA SK450 - page 11
11 W arming oven First touch the “On/O ” key (as p10), then touch the “W arming oven” key . The warming oven programme allows you to prove dough and bake blind, using just heat from below . The cooking temperature defaults to 50°C and can be set between 50-250 (MAX) °C in 5˚C increments. The temperature can be changed at any time by t ...
-
CDA SK450 - page 12
12 Fanned grill First touch the “On/O ” key (as p10), then touch the “Fanned grill” key . The fanned grill programme uses the grill element for grilling and the fan to help circulate heat around the food. This is ideal for cooking on several shelves. The cooking temperature defaults to 165°C and can be set between 50-250 (MAX) °C in 5? ...
-
CDA SK450 - page 13
13 The temperature can be changed at any time by touching the keys. During heating the “°C” symbol flashes and the display shows the actual temperature in the oven. Fan oven + lower heat First touch the “On/O ” key (as p10), then touch the “Fan oven + lower heat” key . The fan oven + lower heat programme uses the fan element to enh ...
-
CDA SK450 - page 14
14 Use of the Food Probe The food probe is a thermometer which, when inserted into your food in the oven, makes it possible to check its internal temperature and use it to establish when it is cooked through. Using the food probe 1. The probe must be plugged into the oven before the oven is switched on. 2. Locate the food probe sock et, situated in ...
-
CDA SK450 - page 15
15 If at any time you want to change either the probe set temperature or the oven setting temperature, touch the “ok” key to toggle the display between the setting temperatures. Then use the keys to adjust the setting. Note: When using the food probe the preset temperatures for all programmes are changed. The cooking temperature with probe defa ...
-
CDA SK450 - page 16
16 preheat” key again, the oven beeps twice and the “R apid preheat” key returns to white lighting to show this is deactivated. Oven clean This function cleans the oven’ s catalytic side and rear panels by running a maximum temperature cycle. The “Oven clean” function can only be used when no cooking function has been selected. First to ...
-
CDA SK450 - page 17
17 the option required then confirm by touching the “ok” key for each selections. At the end of the process the oven displays the set cooking time; this may be adjusted up or down using the “+” and “-” keys, then the “ok” to confirm. Press the “Start” k ey to start the programme running. For some programmes the oven determines ...
-
CDA SK450 - page 18
18 Timer and Minute Minder Programming the oven This is only applicable to these functions:- Fan oven Fan oven + grill Fan grill Grill Any timer functions required should be set after the relevant cooking programme has been set, and before the “ start” key is touched. Timer - Cooking time T ouch the “Timer function” key once so the “Cooki ...
-
CDA SK450 - page 19
19 Programming delayed cooking This is achieved by programming an end time (when you want the food ready) and also programming a cooking time (as the recipe). Minute minder The minute minder is a timer that is independent of the function of the oven; it times and sounds a beep but does not aect any oven functions. This is useful for timing actio ...
-
CDA SK450 - page 20
20 Care and Maintenance IMPORT ANT : Always disconnect the appliance from the power supply before undertaking any cleaning or maintenance. Y ou should always allow the oven to cool fully after use before undertaking any cleaning or maintenance. Changing the oven lamp • R emove all shelves and the grill pan from the oven. • Gently unclip the sid ...
-
CDA SK450 - page 21
21 cause premature failure. Always use a clean cloth or gloves. • R eattach the glass cover , pressing it firmly into position. • Hook the catalytic panel back into position. • R eplace the side rack by locating the two hooks at the top and clipping it back into position on its lower fixing stud. • R eplace the oven shelves and grill pan ...
-
CDA SK450 - page 22
22 Cleaning Y ou should only use non-abrasive cleaners. Any abrasive cleaners (including Cif ) will scratch the surface and could erase the control panel markings. Y ou should not use cleaning products with a chlorine or acidic base. Any spillages should be cleaned o immediately , especially any alkaline or acidic substances (lemon juice, vinega ...
-
CDA SK450 - page 23
23 Catalytic liners The catalytic oven liners must only be cleaned with fresh water . For stubborn stains, boil a cup of water in the oven for 2 to 3 minutes. Steam will soften the marks prior to cleaning. Grill When used regularly , the grill element does not need cleaning as the intense heat will burn o any splashes. The interior ceiling may n ...
-
CDA SK450 - page 24
24 Installation The appliance can be installed under a worktop or in a wall unit (open or closed) with the appropriate dimensions for recessed installation. Centre the oven in the unit so as to ensure a minimum distance of 10mm between the appliance and the surrounding unit. The material of the unit supporting the appliance must be heat resistant ( ...
-
CDA SK450 - page 25
25 Fig. 7 Fig. 6 535 21 594 594 540 560 595 50 510 535 21 594 594 540 560 50 510 595 597 597 ...
-
CDA SK450 - page 26
26 Mains Electricity Connection W arning! This appliance must be earthed W e recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E. T . and local regulations. This appliance is intended to be connected to fix ed wiring and is not suitable for connection to a 13A ...
-
CDA SK450 - page 27
27 This appliance is supplied with a 3 core mains cable; the wires are in accordance with the following code: Green and Y ellow = Earth Blue = Neutral Brown = Live Please note: • The mains cable must only be replaced by a qualified electrician or service engineer and must be of equivalent or better rating (i.e. 1.5mm 2 , HO5V2V2-F). • The curr ...
-
CDA SK450 - page 28
28 NO TES: ...
-
CDA SK450 - page 29
29 NO TES: ...
-
CDA SK450 - page 30
30 NO TES: ...
-
CDA SK450 - page 31
31 E & O E. All instructions, dimensions and illustrations are provided for guidance only . CDA reserve the right to change specifications without prior notice. Attribute Symbol Value Units Model Identification SK450 Mass of the appliance M 37.2 kg Number of cavities 1 Heat source per cavity (electricity ...
-
CDA SK450 - page 32
Please contact our Customer Care Department for Service on the details below . Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu ...
Do you have a question concerning CDA SK450?
Use the form below
If you did not solve your problem by using a manual CDA SK450, ask a question using the form below. If a user had a similar problem with CDA SK450 it is likely that he will want to share the way to solve it.