English dropdown-ico

Manual Milnor K28 0010

21 pages 0.52 mb
Download

Go to site of 21

Summary
  • Milnor K28 0010 - page 1

    Published Manual Number/ECN: H28 0010/2001074N • Publishing System: TPAS • Access date: 2/14/01 • Document ECN's: Latest Available Kit Instruction— K28 0010 K36 0005 K36 0005R PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A. ...

  • Milnor K28 0010 - page 2

    Please Read A bout the Manual Identif y ing Information on the Cover The front cover d isplay s pert inent id entify ing in form ation fo r this m anual. M ost im porta nt, are the publishe d m anual number ( part num ber) /ECN (date code). Ge nerally , when a r eplacem ent manual is furnish ed, it w ill hav e the sam e publis hed m anual num ber, ...

  • Milnor K28 0010 - page 3

    1 ...

  • Milnor K28 0010 - page 4

    MSSM020 4AE/833 2BV (1 of 1) È V-BELT TENSION ADJUSTMENTS FOR 30" AND 36" B-TYPE MACHINES AND 42" Q-TYPE MACHINES This instruction i s to be used for adjus ting the belt tension on the fol lowing machine modes: 30016BWE 42026QHE 36021BWE 42026QTG 360326QWE 42026QTH 42026QWE A belt tension t esting devi ce (Milnor ® part num ber 30T ...

  • Milnor K28 0010 - page 5

    MSSM0301AE/9126B V È V-BELT TENSION ADJUSTMENTS This instruction is to be used for adjusting the belt tension on the following machine models: A belt tension testing device (Milnor ® part number 30T001) and a straight edge are required when using these instructions. Ê Tension Settings Set the o-rings on the tension testing device (FIGURE 1) as f ...

  • Milnor K28 0010 - page 6

    MSSM0301AE/9126BV (1 of 1) È V-BELT TENSION ADJUSTMENTS This instruction is to be used for adjusting the belt tension on the following machine models: A belt tension testing device (Milnor ® part number 30T001) and a straight edge are required when using these instructions. Ê Tension Settings Set the o-rings on the tension testing device (FIGURE ...

  • Milnor K28 0010 - page 7

    M S S M A40 5 A E / 873 7 B V È V-BELT TENSION ADJUSTMENTS FOR 48", 52", 60" AND 72" WASHER-EXTRACTORS This instruction is to be used for adjusting the belt tension on the following machine models: 48032BHE 48032BTG 48032BTH 48036QHE 48036QTG 48036QTH 52038WE1 52038WTF 52038WTB 52038WTG 52038WTH 60036WE2 60036WE3 60036SG2 60036 ...

  • Milnor K28 0010 - page 8

    MS SMA405 AE/ 8737 BV (1 of 2) È V-BELT TENSION ADJUSTMENTS FOR 48", 52", 60" AND 72" WASHER-EXTRACTORS This instruction is to be used for adjusting the belt tension on the following machine models: 48032BHE 48032BTG 48032BTH 48036QHE 48036QTG 48036QTH 52038WE1 52038WTF 52038WTB 52038WTG 52038WTH 60036WE2 60036WE3 60036SG2 6003 ...

  • Milnor K28 0010 - page 9

    Ë Tensioning Banded Belts Ï 48032BHE, BTG , BTH 48 036QHE, QTG, QT Belt Deflect. (inches) Initial Tension (l bs.) (r ef.) Initial Tension (lbs.) (re f.) Belt Deflect (in.) Initial Tension (lbs. ) (re f.) Initial Tension (lbs. ) (re f.) WASH/ 2 SPEED WASH 9/32 6.6 - 9.2 KP3 5.1 - 7.1 KN 5/16 5.7 - 7.6 JP3 4.4 - 5.9 JN DRAIN 5/32 5.7 - 7.6 JP3 4.4 ...

  • Milnor K28 0010 - page 10

    Ë Tensioning Banded Belts Ï 48032BHE, BTG , BTH 48 036QHE, QTG, QT Belt Deflect. (inches) Initial Tension (l bs.) (r ef.) Initial Tension (lbs.) (re f.) Belt Deflect (in.) Initial Tension (lbs. ) (re f.) Initial Tension (lbs. ) (re f.) WASH/ 2 SPEED WASH 9/32 6.6 - 9.2 KP3 5.1 - 7.1 KN 5/16 5.7 - 7.6 JP3 4.4 - 5.9 JN DRAIN 5/32 5.7 - 7.6 JP3 4.4 ...

  • Milnor K28 0010 - page 11

    9 ...

  • Milnor K28 0010 - page 12

    M S S M 030 3 A E / 845 1 B V È MAIN BEARING AND SEAL REPLACEMENT FOR DIVIDED CYLINDER MACHINES This section applies to the front and rear cylinder shaft bearings of all divided cylinder machines (Rapid Load, Staph-guard ® , dye machines , et c.). It does not apply to jackshaft bearings , i dler shaft bear ings or bearings on open pocket machines ...

  • Milnor K28 0010 - page 13

    MSSM 0303 AE/8451 BV (1 of 5) È MAIN BEARING AND SEAL REPLACEMENT FOR DIVIDED CYLINDER MACHINES This section applies to the front and rear cylinder shaft bearings of all divided cylinder machines (Rapid Load, Staph-guard ® , dye machines , et c.). It does not apply to jackshaft bearings , i dler shaft bear ings or bearings on open pocket machines ...

  • Milnor K28 0010 - page 14

    inspection plate and use a timber to pry up the cylinder to remove cylinder weight from the bearings. Once the bearing is removed, the cylinder drops only approximately 1/32" before the shaft comes to rest on the shaft support. 4. Slide the bearing off of the shaft and if it is to be reused, place it on a clean surface and cover with a clean, ...

  • Milnor K28 0010 - page 15

    inspection plate and use a timber to pry up the cylinder to remove cylinder weight from the bearings. Once the bearing is removed, the cylinder drops only approximately 1/32" before the shaft comes to rest on the shaft support. 4. Slide the bearing off of the shaft and if it is to be reused, place it on a clean surface and cover with a clean, ...

  • Milnor K28 0010 - page 16

    Ê Replacing the Bearing Housing, Seal Sleeve, and Seals (Front or Rear) 1 . With the seal sleeve removed, press all old seals out of the bearing housing. Remove the large o-ring from the outside of the housing. Thoroughly clean the bearing housing and flush out all grease passages to make cer- tain they are unblocked. Remove the o-rings from the i ...

  • Milnor K28 0010 - page 17

    Ê Replacing the Bearing Housing, Seal Sleeve, and Seals (Front or Rear) 1 . With the seal sleeve removed, press all old seals out of the bearing housing. Remove the large o-ring from the outside of the housing. Thoroughly clean the bearing housing and flush out all grease passages to make cer- tain they are unblocked. Remove the o-rings from the i ...

  • Milnor K28 0010 - page 18

    Ê Measuring Unmounted Clearance and Setting Bearing (Front or Rear) The bearings used on Milnor ® washer and dye extractors are the very best anti-friction devices available for these applicati ons. However, the anti-frict ional characteristi cs of the bearings will be reduced if they ar e not proper- ly inst alled. It is of critical importance w ...

  • Milnor K28 0010 - page 19

    Ê Measuring Unmounted Clearance and Setting Bearing (Front or Rear) The bearings used on Milnor ® washer and dye extractors are the very best anti-friction devices available for these applicati ons. However, the anti-frict ional characteristi cs of the bearings will be reduced if they ar e not proper- ly inst alled. It is of critical importance w ...

  • Milnor K28 0010 - page 20

    Ê Tightening Bearing(s) (Front and/or Rear) 1. Once both bearings are seated, or if only one bearing was replaced, install the bearing lockwasher(s) and lock- nut(s). Use a hammer and a metal drift as shown in FIGURE 11, to tighten the locknut. It is imp erative to only tap lightly and to assure that metal chips from the drift or locknut do not fa ...

  • Milnor K28 0010 - page 21

    Ê Tightening Bearing(s) (Front and/or Rear) 1. Once both bearings are seated, or if only one bearing was replaced, install the bearing lockwasher(s) and lock- nut(s). Use a hammer and a metal drift as shown in FIGURE 11, to tighten the locknut. It is imp erative to only tap lightly and to assure that metal chips from the drift or locknut do not fa ...

Manufacturer Milnor Category Washer

Documents that we receive from a manufacturer of a Milnor K28 0010 can be divided into several groups. They are, among others:
- Milnor technical drawings
- K28 0010 manuals
- Milnor product data sheets
- information booklets
- or energy labels Milnor K28 0010
All of them are important, but the most important information from the point of view of use of the device are in the user manual Milnor K28 0010.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Milnor K28 0010, service manual, brief instructions and user manuals Milnor K28 0010. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Milnor K28 0010.

Similar manuals

A complete manual for the device Milnor K28 0010, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Milnor K28 0010 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Milnor K28 0010.

A complete Milnor manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Milnor K28 0010 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Milnor K28 0010, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Milnor K28 0010, that we can find in the current document
3. Tips how to use the basic functions of the device Milnor K28 0010 - which should help us in our first steps of using Milnor K28 0010
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Milnor K28 0010
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Milnor K28 0010 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Milnor K28 0010?

Use the form below

If you did not solve your problem by using a manual Milnor K28 0010, ask a question using the form below. If a user had a similar problem with Milnor K28 0010 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)