-
Dymo M1011 - page 1
Rhino M1011 www.dymo.com User Guide Guide D’Utilisation Bedienungsanleitung Guida per l’utente Guía del usuario Guia do Usuário ...
-
Dymo M1011 - page 2
2 A T ape cassette door H Charac ter selec tio n window B Ta p e r o l l e r s I Cutting handle C T ape advance knob J Embossing adjustment scr ew D Start line K Cable tie slot entrance E T ape pawl L Hole punch entrance F Embossing handle M Ta p e e x i t G Embossing wheel N T railer le ngth guide A B C D F G H I K L M J N E ...
-
Dymo M1011 - page 3
3 About Y our New Label Maker W i th your new D YMO M1011 label mak er, you can cr eate metal labels . The label mak e r uses DY MO 12 mm (1/2") tape. Metal tapes are available as follows: • Aluminium with a dhesive (35800) • Aluminium without adhesiv e (31000) • Stainless Steel (32500) Y ou can also use a Reverse Image Wheel with the DY ...
-
Dymo M1011 - page 4
4 Loading the T ape The D YMO M1011 is set to emboss non-adhesive aluminium tape. T o load the tape roll 1. Hold the label maker in your lef t hand. 2. Open tape cassette door (A ). 3. I n se r t rol l of ta pe a ll ow in g t h e e nd to ex t en d a bo u t 5 cm (2 " ) t hro u gh the label sl ot. 4. Close the tape cassette door . 5. F eed the t ...
-
Dymo M1011 - page 5
5 Cutting the Label To c u t t h e l a b e l 1. Squeeze the embossing handle half-way , several times until the tape extends from the front of the tape exit (M) by at least 2,5 cm (1"). Before cutting the tape, make sure the end of the tape e x tends beyond the edge of the cutting asse mbly so you can easi ly pull the label out . Other wise, a ...
-
Dymo M1011 - page 6
6 Embossing the L abel A void turning the embossing wheel at the same time y ou are squeezing the embossing handl e. This can damage the character wheel. T o emboss a label 1. T urn the character selection wheel (G) until the desired lett er is centered in the window (H). 2. Squeeze the embossing handle (F) firmly . 3. Release the embo ssing handle ...
-
Dymo M1011 - page 7
7 Embossing on S tainless Steel Label Y ou may need to adjust the labelmak er t o emboss properly when using stainless steel tape. T o adjust for stainless steel la bel 1. T urn the adjustmen t screw (J) clockwise 3/4 t o 1 turn. 2. Emboss the t ext as described in “Embossing the Label ” on page 6. When you r eturn to using aluminum tape, y ou ...
-
Dymo M1011 - page 8
8 Retracting the Label Y ou may want t o retract the tape, for e xample, if the tape adva nced too far or to center the text on the label. T o retrac t the label 1. Pull back the pa wl (E). 2. T urn th e tape advanc e knob (C) count er-clockwise. E C ...
-
Dymo M1011 - page 9
9 Removing the Label T o remov e the label 1. Retract the tape as described in “Retrac ting the Label” on page 8. 2. Open the tape cassette door (A ) and remove the label. Use caution when removi ng stainless steel tape that may hav e sharp edges. 3. Reload the tape as described in “Loading the T ape” on page 4. A ! ...
-
Dymo M1011 - page 10
10 Centering the T ext on the Label The trai ler length guide (N) has posi tioning marks for a short (S) or long label (L). Use the ma rks on the guide to center the text on your label. T o center the t ext on a long label 1. A fter cutting the pr evious label, emboss the text on a new la bel. 2. Pull the trailer length guide (N) to the for ward po ...
-
Dymo M1011 - page 11
11 Applying S elf-Adhesiv e Labels Self-adhesiv e aluminum tape sticks permanently to any smooth, clean, and dry surface. T o apply self-adhesiv e tape 1. P eel off the protective backing taki ng care not to touch the adhesiv e. 2. Press the label in place. 3. Apply firm pressure along the entire length to ensure good contact. ...
-
Dymo M1011 - page 12
12 Punching Holes in Non-Adhesive Labels Y ou can choose to punch one or two holes in non-ad hesive labels so tha t the labels can be attached using screws , nails, riv ets, an d metal or plastic wires or ties. Y ou can also punch a cable tie slot in one or both ends of the label. T o punch a hole 1. Insert one en d of the cut label into the hole p ...
-
Dymo M1011 - page 13
13 Changing the Wheel Y ou can replace the character wh eel with a Reverse Image Wheel. T o change the wheel 1. Remove the tape . 2. Unscrew the screw in the center of the embossing wheel (G) and remo ve the wheel. 3. P osition the new wheel. 4. Insert t he screw in the center and tighten. Do not tighten the screw too tightly . G ...
-
Dymo M1011 - page 14
14 Hints for T rouble Free O peration Keep the following in mind when usi ng the label maker: • Letters appear where you wan t spaces - Y ou are probably squeezing the embossing handle too har d. • Letters overlap - The tape is slipping. This can happen when dir t or grease gets on the rollers. Clean the rollers by usin g a soft cloth and alcoh ...
-
Dymo M1011 - page 15
15 Warranty Registra t ion This D YMO M1011 has been manufact ur ed under strict quality contro l and performance tested befor e leaving the factory . Within one y ear after purchase , DYMO will repair or replac e, at its own option, the M1011 free of charge if sent prepai d by the purchaser to D YMO and found, in DY MO ’ s judgement, to be defec ...
-
Dymo M1011 - page 16
Distributed by/Distribué par/Distribuido por: DYMO , Atlanta, GA 30328 ©2010 Sanford, L.P . www .dymo.com Imported into Canada by/Importé au C anada par Sanford Canada L.P ., Oakville, ON L6J 3J3 En México importado y distribuido por: Newell Rubbermaid de México S. de R.L. de C.V . Av . Vasco de Quiroga 3000 P . Plaza 1, Col. Santa F e, Del. A ...
Do you have a question concerning Dymo M1011?
Use the form below
If you did not solve your problem by using a manual Dymo M1011, ask a question using the form below. If a user had a similar problem with Dymo M1011 it is likely that he will want to share the way to solve it.