English dropdown-ico

Manual Wayne-Dalton 9600

8 pages 0.24 mb
Download

Go to site of 8

Summary
  • Wayne-Dalton 9600 - page 1

    T orqueMaster™ & i drive™ 9900/9600/9200/9100 INST ALLA TION INSTRUCTION SUPPLEMENT When installing an idrive™ opener with this door use this supplement to the main door instructions as follows: 1) Begin with Step 1 of the main door instructions. 2) Replace Step 8 of the main door instructions with Step 8 of the attached supplement. 3) Re ...

  • Wayne-Dalton 9600 - page 2

    ® Follow the corresponding steps in this insert with the steps in the installation manual provided with the door . These modifications are designed to accommodate the new i drive™ garage door opener . T op Bracket Inst allation TOP SECTION RIB (2) CARRIAGE BOL TS TOP BRACKET TOP BRACKET SLIDE 3) 9200/9100 Foamcore™ (below) will have galvanized ...

  • Wayne-Dalton 9600 - page 3

    TORQUE TUBE PLUG MOTOR INTO THE OPENER POWER HEAD SLIDE OPENER POWER HEAD LABEL (LEFT SIDE) TORQUE TUBE INSERT THIS END FROM LEFT SIDE OF OPENER Continue sliding the opener power head onto the torque tube. Align the right hand bearing with the torque tube and slide the opener power head completely onto the torque tube until the torque tube exits th ...

  • Wayne-Dalton 9600 - page 4

    Refer back to the main door manual and continue door installation at the REAR SUPPOR T INST ALLA TION S tep 18. ( S tep 19 in the Single Spring T orqueMaster™ Installation Instructions) After door installation is completed, refer to the i drive™ owner ’ s manual, starting at the PRE-OPERA TION INST ALLA TION section to complete the opener ins ...

  • Wayne-Dalton 9600 - page 5

    Drum Installation TORQUE TUBE WINDING SHAFT DRUM TORQUE TUBE LOOSE WINDING SHAFT DRUM WINDING SHAFT GROOVE ROUND NOTCH FLAG ANGLE Shake the torque tube gently to extend the winding shafts out about 5" on each side. For single spring applications, there will be no left hand winding shaft in the torque tube. Lift the torque tube and rest on top ...

  • Wayne-Dalton 9600 - page 6

    Using the emergency disconnect, pull disconnect handle downwards and place it in the manual door operated position. Use disconnect label for reference. Motor will be rotated 90° from its packaged position. NOTE: If motor does not pivot 90°, see troubleshooting section in the i drive™ main installation manual. Wind Counterbalance Springs 7 IMPOR ...

  • Wayne-Dalton 9600 - page 7

    Slide the right hand end bracket over the drive gear . Attach end bracket and the flagangle to the jamb with (2) 5/16 x 1-5/8” lag screws. (see Fig. 1 1 ) 5 OPENER POWER HEAD SPRING P AD TORQUE TUBE MOUNTING STUDS Power Head/ Support Bracket Installation (2) 2” LAG SCREWS SUPPORT BRACKET MOTOR (2) 1/4-20 FLANGE NUTS Locate the spring pad. The s ...

  • Wayne-Dalton 9600 - page 8

    power head. W ith slack removed, secure bottom of handle bracket with (1) 1/4 x 1-1/2" lag screw . CAUTION : Pull handle just enough to remove the cable slack. Pulling the cable more could cause the opener power head to disconnect from the torque tube. Rotate disconnect handle to one side exposing upper mounting hole in handle bracket. Secure ...

Manufacturer Wayne-Dalton Category Door

Documents that we receive from a manufacturer of a Wayne-Dalton 9600 can be divided into several groups. They are, among others:
- Wayne-Dalton technical drawings
- 9600 manuals
- Wayne-Dalton product data sheets
- information booklets
- or energy labels Wayne-Dalton 9600
All of them are important, but the most important information from the point of view of use of the device are in the user manual Wayne-Dalton 9600.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Wayne-Dalton 9600, service manual, brief instructions and user manuals Wayne-Dalton 9600. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Wayne-Dalton 9600.

Similar manuals

A complete manual for the device Wayne-Dalton 9600, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Wayne-Dalton 9600 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Wayne-Dalton 9600.

A complete Wayne-Dalton manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Wayne-Dalton 9600 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Wayne-Dalton 9600, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Wayne-Dalton 9600, that we can find in the current document
3. Tips how to use the basic functions of the device Wayne-Dalton 9600 - which should help us in our first steps of using Wayne-Dalton 9600
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Wayne-Dalton 9600
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Wayne-Dalton 9600 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Wayne-Dalton 9600?

Use the form below

If you did not solve your problem by using a manual Wayne-Dalton 9600, ask a question using the form below. If a user had a similar problem with Wayne-Dalton 9600 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)