English dropdown-ico

Manual Husqvarna LTH2042

44 pages 1.79 mb
Download

Go to site of 44

Summary
  • Husqvarna LTH2042 - page 1

    02494 L TH2042 Owner's Manual 02578_husqvarna ...

  • Husqvarna LTH2042 - page 2

    2 DO NO T : • Do not turn on slopes unless necessar y , and then, turn slowly and gradually downhill, if possib le. • Do not mow near drop-offs , ditches, or embankments. The mower could suddenly turn ov er if a wheel is ov er the edge of a cliff or ditch, or if an edge cav es in. • Do not mow on wet g rass. Reduced traction could cause slidi ...

  • Husqvarna LTH2042 - page 3

    3 W ARNING: In order to prevent ac- ci den tal starting when setting up, trans por t ing, ad just ing or making re- pairs, al ways dis con nect spark plug wire and place wire where it can not contact spark plug. W ARNING: Do not coast down a hill in neutral, you ma y lose control of the tractor . W ARNING: T ow only the attac hments that are rec om ...

  • Husqvarna LTH2042 - page 4

    4 GASOLINE CAP A CITY 4.0 GALLONS AND TYPE: UNLEADED REGULAR OIL TYPE (API-SF-SJ): SAE 10W30 (abov e 32°F) SAE 5W -30 (below 32°F) OIL CAP A CITY : 3.0 PINTS SP ARK PLUG: CHAM PI ON RC12YC (GAP: .030") GROUND SPEED (MPH): F orward: 0-5.5 Re verse 0-2.4 TIRE PRESSURE: FRONT : 14 PSI REAR: 10 PSI CHARGING SYSTEM: 15 Amps @ 3600 RPM BA TTER Y : ...

  • Husqvarna LTH2042 - page 5

    5 UNASSEMBLED P AR TS (1) Large Flat Washer Steering Wheel Insert Steering Sleeve Steering Wheel (1) Knob (1) Washer 17/32 x 1-3/16 x 12 Gauge Seat (2) Keys Slope Sheet Steering Extension Shaft Steering Adapter (1) Oil Drain Tube (1) Hex Bolt 1/4-28 x 1-1/4 (1) Locknut 1/4-28 (1) Locknut 1/2-20 (4) Washers 3/8 x 3/4 x 14 Ga. (4) Wheels (4) Adjustin ...

  • Husqvarna LTH2042 - page 6

    6 02601 ASSEMBL Y T OOLS REQUIRED FOR ASSEMBL Y A sock et wrench set will make assemb ly easier . Stan dard wrench sizes are listed. Utility knif e Pliers (1) 3/4" wrenches Tire pressure gauge (2) 7/16" wrenches Utility knif e When right or left hand is mentioned in this man ual, it means when you are in the oper ating po si tion (seated ...

  • Husqvarna LTH2042 - page 7

    7 ASSEMBL Y FIG. 3 SEA T P AN SHOULDER BOL T ADJUSTMENT KNOB FLA T W ASHER SEA T HO W T O SET UP Y OUR TRA CT OR INST ALL SEA T (See Fig. 3) Adjust seat bef ore tightening adjustment knob. • Remov e adjustment knob and fl at washer securing seat to cardboard packing and set aside f or assembly of seat to tractor . • Piv ot seat upward and remo ...

  • Husqvarna LTH2042 - page 8

    8 ASSEMBL Y ✓ CHE CKLIST BEFORE Y OU OPERA TE AND ENJO Y Y OUR NEW TRAC- T OR, WE WISH TO ASSURE THA T Y OU RECEIVE THE BEST PERFORMANCE AND SA TISF ACTION FR OM THIS QU ALITY PRODUCT . PLEASE REVIEW THE FOLLOWING CHECKLIST : ✓ All assemb ly instructions have been completed. ✓ No remaining loose par ts in car ton. ✓ Batter y is properly pre ...

  • Husqvarna LTH2042 - page 9

    9 OPERA TION These symbols ma y appear on your tractor or in literature supplied with the product. Lear n and understand their mean- ing. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only) OVER TEMP LIGHT KEEP AREA CLEAR SLOPE HAZARDS 15 15 (SEE SAFETY RULES SECTION) BATTERY REVERSE FORWARD FAST SLOW ENGINE ON ENGINE OFF OIL PRESSU ...

  • Husqvarna LTH2042 - page 10

    10 OPERA TION KNO W Y OUR TRA CT OR READ THIS O WNER'S MANU AL AND SAFETY RULES BEFORE OPERA TING Y OUR TRACT OR Compare the illustrations with y our tractor to familiarize y ourself with the locations of various controls and ad just ments. Sav e this manual f or future ref erence. Our tractors conf or m to the saf ety standards of the America ...

  • Husqvarna LTH2042 - page 11

    11 OPERA TION The operation of any tractor can result in f oreign objects thro wn into the eyes, which can result in severe e ye dam age. Al ways wear safety glass es or eye shields while operating your tractor or per form ing an y adjustments or repairs. We rec om mend a wide vision safety mask over spectac les or stan dard safety glasses. HO W T ...

  • Husqvarna LTH2042 - page 12

    12 OPERA TION T O OPERA TE ON HILLS W ARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across an y slope. • Choose the slo west speed bef ore star ting up or down hills. • A void stopping or changing speed on hills . • If slowing is necessar y , mov e throttle control lev er to slower position. • If stopp ...

  • Husqvarna LTH2042 - page 13

    13 OPERA TION FIG. 9 ADD GASOLINE • Fill fuel tank to bottom of fi ller neck. Do not overfi ll. Use fresh, clean, regular un lead ed gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead o xide deposits and reduce valv e life). Do not mix oil with gasoline. Purchase fuel in quan ti ties that can be used wit ...

  • Husqvarna LTH2042 - page 14

    14 FIG. 10 MO WING TIPS • Mower should be properly lev eled for best mowing per- f or mance. See “T O LEVEL MOWER HOUSING” in the Ser vice and Adjustments section of this manual. • The left hand side of mow er should be used for trim- ming. • Drive so that clippings are discharged onto the area that has been cut. Hav e the cut area to the ...

  • Husqvarna LTH2042 - page 15

    15 MAINTENANCE BEFORE EACH USE T R A C T 0 R Inspect Muffler/Spark Arrester Lubrication Chart Check Brake Operation Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartridge Replace Spark Plug Check Battery Level Check Tire Pressure Clean Battery and Terminals FILL IN DATES AS YOU COMPLETE REGULAR SERVICE MAINTENANCE S ...

  • Husqvarna LTH2042 - page 16

    16 MAINTENANCE BLADE REMO V AL (See Fig. 11) • Raise mower to highest position to allow access to blades . • Remov e blade bolt, loc k washer and fl at washer se cur ing bla de. • Install new or resharpened blade with trailing edge up tow ards deck as shown. IMPORT ANT : T O ENSURE PROPER ASSEMBL Y , CENTER HOLE IN BLADE MUST ALIGN WITH ST A ...

  • Husqvarna LTH2042 - page 17

    17 MAINTENANCE V- B E LT S Check V -belts for deterioration and wear after 100 hours of operation and replace if necessary . The belts are not ad just able. Re place belts if they begin to slip from w ear . TRANSAXLE COOLING The transmission f an and cooling fi ns should be kept clean to assure proper cooling. Do not attempt to clean f an or trans ...

  • Husqvarna LTH2042 - page 18

    18 MAINTENANCE MUFFLER Inspect and replace corroded muffl er and spark arrester (if equipped) as it could create a fi re hazard and/or dam- age. SP ARK PLUGS Replace spark plugs at the beginning of each mowing season or after e very 100 hours of operation, whichev er occurs fi rst. Spar k plug type and gap setting are shown in “PROD UCT SPECIF ...

  • Husqvarna LTH2042 - page 19

    19 SER VICE AND ADJUSTMENTS W ARNING: T O A V OID SERIOUS INJURY , BEFORE PERFORMING ANY SER VICE OR AD JUST - MENTS • Depress clutch/brake pedal full y and set parking brake. • Place motion control le ver in neutral (N) position. • Place attachment clutc h in “DISENGAGED” position. • T urn ignition key to “STOP” and remove ke y . ? ...

  • Husqvarna LTH2042 - page 20

    20 SER VICE AND ADJUSTMENTS NUT "E" "D" "D" MANDREL FIG. 19 NUT "F" FRONT LINKS FIG. 20 FRONT -T O-BACK ADJUSTMENT (See Figs . 19 and 20) IMPORT ANT : DECK MUST BE LEVEL SIDE-T O-SIDE. IF THE FOLLO WING FRONT -TO-BA CK ADJUSTMENT IS NECESSARY , BE SURE T O AD JUST BOTH FR ONT LINKS EQU AL LY S O MO WER WILL S ...

  • Husqvarna LTH2042 - page 21

    21 SER VICE AND ADJUSTMENTS FIG. 21 T O REPLACE MO WER BLADE DRIVE BEL T (See Fig. 21) The mower b lade drive belt ma y be replaced without tools. P ark the tractor on lev el surface. Engage par king brake . BEL T REMO V AL - • Remov e mow er from tractor (See “T O REMO VE MO W ER” in this section of man ual). • Work belt off both mandrel p ...

  • Husqvarna LTH2042 - page 22

    22 SER VICE AND ADJUSTMENTS T O REMO VE WHEEL FOR REP AIRS (See Fig. 25) • Block up axle securely . • Remov e axle cover , retaining r ing and washers to allow wheel remov al (rear wheel contains a square ke y - Do not lose). • Repair tire and reassemble . • On rear wheels only: align g roov es in rear wheel hub and axle. Inser t square ke ...

  • Husqvarna LTH2042 - page 23

    23 SER VICE AND ADJUSTMENTS T O REPLACE HEADLIGHT B ULB • Raise hood. • Pull bulb holder out of the hole in the backside of the grill. • Replace bulb in holder and push b ulb holder securely back into the hole in the bac kside of the grill. • Close hood. INTERLOCKS AND RELA YS Loose or damaged wiring may cause y our tractor to run poorly , ...

  • Husqvarna LTH2042 - page 24

    24 ST ORA GE Immediately prepare your tr actor for storage at the end of the season or if the tractor will not be used f or 30 days or more. W ARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reac h an open fl ame or spark. Allow the engine to cool bef ore storing in any en c lo sure . TRA CT OR Remov ...

  • Husqvarna LTH2042 - page 25

    25 TR OUBLESHOO TING POINTS Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “T O ST ART ENGINE” in Operation section. 3. Engine fl ooded. 3. Wait se ver al minutes before attempting to start. 4. Bad spar k plug. 4. Replace spar k plug. 5. Dir ty air fi lter . 5. Clean/replace air fi lter . 6. Di ...

  • Husqvarna LTH2042 - page 26

    26 TR OUBLESHOO TING POINTS Engine continues to run 1. F aulty operator-saf ety presence control system. 1. Check wiring, switches and connections. If not when operator leaves seat corrected, contact an author ized service center/ with attachment clutc h depar tment. engaged P oor cut - uneven 1. Worn, bent or loose blade. 1. Replace b lade. Tighte ...

  • Husqvarna LTH2042 - page 27

    27 BATTERY FUSE IGNITION SWITCH RED RED RED BLACK IGNITION UNIT HEADLIGHTS NON-REMOVABLE CONNECTIONS REMOVABLE CONNECTIONS BLACK BLACK BLACK WHITE WHITE WHITE RED BLACK ORANGE BLACK BROWN BLACK BLACK BLACK STARTER M SEAT SWITCH (NOT OCCUPIED) GROUNDING CONNECTOR ATT'MENT CLUTCH (CLUTCH OFF) CLUTCH / BRAKE (PEDAL UP) SOLENOID BLACK WIRING INSUL ...

  • Husqvarna LTH2042 - page 28

    28 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 ELECTRICAL 28 29 26 24 42 43 27 27 25 41 27 27 40 33 30 12 12 11 10 8 2 1 27 52 16 16 D .C . A M P E R E S 45 22 21 55 ...

  • Husqvarna LTH2042 - page 29

    29 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 ELECTRICAL KEY P ART NO . NO . DESCRIPTION 1 532 14 49-27 Batter y 2 874 76 04-12 Bolt He x Hd 1/4-20 unc x 3/4 8 532 12 48 86 T ra y Batter y 10 532 14 52-11 Bolt 1/4-20 x 7.5 11 532 15 01-09 Hold down Battery Front Mount 12 532 14 57-69 Nut Push Nylon 1/4 ...

  • Husqvarna LTH2042 - page 30

    30 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 CHASSIS AND ENCLOSURES 64 74 10 30 208 13 208 11 209 31 1 209 2 9 209 208 209 5 5 207 144 26 26 60 26 144 26 10 209 209 142 209 142 143 60 145 37 37 18 206 14 14 38 38 219 20 219 23 17 261 28 259 260 258 166 39 90 159 217 212 chassis-husqy .stlt_19 58 ...

  • Husqvarna LTH2042 - page 31

    31 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 CHASSIS AND ENCLOSURES KEY P ART NO . NO . DESCRIPTION NO TE: All component dimensions given in U .S. inches 1 inch = 25.4 mm 1 532 17 46-19 Chassis Stamping 2 532 17 65-54 Dra wbar 5 532 15 52-72 Bumper 9 532 17 17-08 Dashboard 10 872 14 06-08 Bolt Rdhd Sq ...

  • Husqvarna LTH2042 - page 32

    32 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 DRIVE 66 29 28 32 30 52 32 59 38 61 41 53 35 55 36 62 35 36 22 39 34 16 1 77 77 30 52 56 64 65 212 63 116 70 57 96 26 25 19 24 26 26 76 78 75 74 27 26 15 37 120 89 90 27 51 48 151 202 49 47 50 120 81 156 166 165 82 168 163 14 112 21 8 10 83 159 161 198 158 ...

  • Husqvarna LTH2042 - page 33

    33 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 DRIVE KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NO TE: All component dimensions giv e in U .S. inches. 1 inch = 25.4 mm. 1 - - - - - - - - T ransaxle Hydro Gr Model 314-0510 (Order par ts from transaxle mfg.) 8 532 16 58-66 Rod Shift F ...

  • Husqvarna LTH2042 - page 34

    34 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 STEERING ASSEMBL Y 5 5 3 43 95 43 8 10 40 11 8 6 87 46 46 8 6 87 29 88 71 17 43 91 2 1 41 42 37 36 37 38 12 39 44 51 54 68 67 67 67 13 65 68 15 15 15 29 29 82 4 32 26 30 28 steering_pl.lt_47 ...

  • Husqvarna LTH2042 - page 35

    35 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 STEERING ASSEMBL Y KEY P ART NO . NO . DESCRIPTION 1 532 16 66-27 Wheel Steering 2 532 18 47-06 Axle Asm 3 532 16 98-40 Spindle Asm LH 4 532 16 98-39 Spindle Asm RH 5 532 12 49-31 Bearing Race Thrust Harden 6 532 12 17-48 W asher 25/32 x 1-5/8 x 16 Ga. 8 81 ...

  • Husqvarna LTH2042 - page 36

    36 1 532 17 08-05 Control Throttle/Choke Flag 2 817 72 04-08 Screw He x Thd Cut 1/4-20 x 1/2 3 - - - - - - - - Engine, K ohler SV600 (Order par ts from engine manuf ac- turer) 4 532 18 86-55 Muffl er 8 532 17 18-77 Bolt 5/16-18 unc x 3/4 13 532 18 59-09 Gasket Eng 14 532 14 84-56 T ube Dr ain Oil Easy 23 532 16 98-37 Shield Br n/Dbr Guard 29 532 1 ...

  • Husqvarna LTH2042 - page 37

    37 KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 532 19 01-20 Seat 2 532 14 05-51 Brac ket Piv ot Seat 8 720 3 871 11 06-16 Bolt Fin He x 3/8-16 unc X 1 4 819 13 16-10 W asher 13/32 x 1 x 10 Ga. 5 532 14 50-06 Clip Push-In 6 873 80 06-00 Nut He x w/Ins. 3/8-16 unc 7 532 12 41-81 Spring Seat Cprsn 2 250 Blk Zi 8 817 00 06-16 Scre ...

  • Husqvarna LTH2042 - page 38

    38 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 DECALS KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 532 05 91-92 Cap V alv e Tire 2 532 06 51-39 Stem V alv e 3 532 10 62-22 Tire F Ts 15 x 6 0 - 6 Service 4 532 05 99-04 T ube F ront (Ser vice Item Only) 5 532 13 83-36 Rim Asm 6" ...

  • Husqvarna LTH2042 - page 39

    39 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 MO WER LIFT 15 20 16 17 18 20 20 15 20 4 5 6 2 3 1 6 5 4 7 8 12 11 31 32 31 32 19 19 13 13 13 13 lift-rh.1piece_3 1 532 15 94-60 Wire Asm Inner W/plunger L T 2 532 15 94-71 Shaft Asm Lift 3 532 10 57-67 Pin Groov e 4 812 00 00-02 E Ring #5133-62 5 819 21 16 ...

  • Husqvarna LTH2042 - page 40

    40 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 MO WER DECK 15 14 13 11 10 9 8 16 68 30 31 32 33 146 148 145 150 45 144 147 147 142 149 142 54 52 53 55 56 34 1 46 44 21 24 25 26 27 2 28 29 23 21 21 21 18 18 20 2 48 59 19 4 5 6 21 40 143 36 40 40 159 140 184 42_D_man-t-path_stlt_4. 3 129 92 131 130 92 118 ...

  • Husqvarna LTH2042 - page 41

    41 REP AIR P ARTS TRA CT OR - - MODEL NUMBER L TH2042 (L TH2042A), PRODUCT NO . 954 57 19-53 MO WER DECK 1 532 18 20-32 Deck Asm 42"weldment 2 872 14 05-06 Bolt Rdhd Sqnk 5/16-18 unc x 3/4 3 532 13 80-17 Brac ket Asm F r Sway Bar 38/42 4 532 16 54-60 Brac ket Asm Dec k 42"sw ay Bar 5 532 12 46-70 Retainer Spring 6 532 17 80-24 Deck Sw ay ...

  • Husqvarna LTH2042 - page 42

    42 SECTION 1: LIMITED W ARRANTY Husqvarna Forest & Garden Compan y (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship from the date of purchase for the “W arranty P eriod” of the product as set forth below: Lifetime W arranty: All tiller tines against breakage, trimmer ...

  • Husqvarna LTH2042 - page 43

    43 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to preven ...

  • Husqvarna LTH2042 - page 44

    44 532 18 99-02 Re v . 2 5.26.04 RD/MH Printed in U.S .A. ...

Manufacturer Husqvarna Category Lawn Mower

Documents that we receive from a manufacturer of a Husqvarna LTH2042 can be divided into several groups. They are, among others:
- Husqvarna technical drawings
- LTH2042 manuals
- Husqvarna product data sheets
- information booklets
- or energy labels Husqvarna LTH2042
All of them are important, but the most important information from the point of view of use of the device are in the user manual Husqvarna LTH2042.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Husqvarna LTH2042, service manual, brief instructions and user manuals Husqvarna LTH2042. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Husqvarna LTH2042.

Similar manuals

A complete manual for the device Husqvarna LTH2042, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Husqvarna LTH2042 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Husqvarna LTH2042.

A complete Husqvarna manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Husqvarna LTH2042 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Husqvarna LTH2042, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Husqvarna LTH2042, that we can find in the current document
3. Tips how to use the basic functions of the device Husqvarna LTH2042 - which should help us in our first steps of using Husqvarna LTH2042
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Husqvarna LTH2042
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Husqvarna LTH2042 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Husqvarna LTH2042?

Use the form below

If you did not solve your problem by using a manual Husqvarna LTH2042, ask a question using the form below. If a user had a similar problem with Husqvarna LTH2042 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)