English dropdown-ico

Manual Belling BEL IHT60

24 pages Not applicable
Download

Go to site of 24

Summary
  • Belling BEL IHT60 - page 1

    Belling IHT60 UK Part No 083352000 Date 3/04/2014 Users Guide & Installation Handbook ...

  • Belling BEL IHT60 - page 2

    CONTENTS & INTRODUCTION CONTENTS • SAFET Y • USING THE PRODUCT • CLEANING • INST ALL A TION INSTRUCTIONS • TECHNICAL DA T A • CUSTOMER CARE INTRODUCTION Thank you for buying this British- built appliance from us. This guide book is designed to help you through each step of owning your new appliance, from installation to use. Please ...

  • Belling BEL IHT60 - page 3

    SAFETY 5.162 BEFORE USING THE PRODUCT Make sure that you ha ve removed all packaging and wrapping. Some of the items inside this appliance may have additional wrapping. GENERAL WARNING! - The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating elements. Children less than 8 years of age shall be ...

  • Belling BEL IHT60 - page 4

    SAFETY 5.162 during use, as this will seriously affect the safet y and performance, particularly in relation to surface temper atures becoming hot and gas oper ated parts not working efciently . The cooling fan (if t ted) is designed to run on after the control knob has been switched off . WARNING! - Do not spr ay aerosols in the vicinity of ...

  • Belling BEL IHT60 - page 5

    SAFETY 5.162 electrical switch. Contact your local gas supplier immediately . ELECTRIC INDUCTION HOB WARNING:- Unattended cooking on a hob can be dangerous and may result in r e. NEVER try to extinguish a re with water , but switch off the appliance and then cover ame e.g. with a lid or a damp cloth. Danger of re: do not store items on ...

  • Belling BEL IHT60 - page 6

    SAFETY 5.162 fail-saf e. The pacemaker must be designed in compliance with the appropriate regulations. Caution: This appliance is for cooking purposes only . It must not be used for other purposes, f or example room heating. Caution: The use of a gas cooking appliance results in the production of heat, moisture and products of combustion in the ro ...

  • Belling BEL IHT60 - page 7

    SAFETY 5.162 the hob when you’re not around - take them of f the cook zone if you have to lea ve the kitchen even if you think it will only be for a moment, while you answer the door or phone. If you use a griddle plate ensure it is completely cool before at tempting to lift it from the hob as residual heat may cause burns, Alwa ys use oven glove ...

  • Belling BEL IHT60 - page 8

    SAFETY 5.162 This hob is not intended to be opertated by means of a external timer or seperate remote control system. Fire Safety Advice Most kitchen res occur when people are distracted or leav e things unattended, so remember: If you’re called awa y from the cooker - by the phone or someone at the door , either take pans off the heat, or swi ...

  • Belling BEL IHT60 - page 9

    USING THE HOB - INDUCTION Before using your hob It is recommended that you clean and wash the hob surface bef ore using for the rst time. Apply a thin coat of ceramic hob cleaner to the hob to maintain and protect it. See the customer care section for details of how to obtain all the av ail- able cleaning products. TOUCH CONTROLS The touch contr ...

  • Belling BEL IHT60 - page 10

    USING THE HOB To de-activate the child lock: 1) Select the On/Off K ey . (L wil l be dis - played on all Cook Z ones). 2) Simultaneously touch the RHF cook zone and the down [-] key , the hob should beep. 3) Remov e ngers and touch the down [-] key again. (The hob should switch off ). 4) When you now switch on the hob “0” will be displayed i ...

  • Belling BEL IHT60 - page 11

    USING THE HOB up [+] and down [-] keys. Pressing down [-] rst sets the timer to 30 minutes. This can then be adjusted using the up [+] and down [-] keys. 4) The maximum time that can be set is 99 minutes. 5)The minute minder is now set and be - gins counting down. 6) Y ou can now use the hob as normal. 7) If the hob is turned off then minute min ...

  • Belling BEL IHT60 - page 12

    USING THE HOB been selected. 2) Select the timer by pressing the up [+] and down [-] keys simultaneously . 3) Press the up [+] and down [-] keys as many times as necessary to display the timer for the required cook zone (the active cook zone times are cycled clockwise). The stationary dot in the cook zone display will ash when the timer is displ ...

  • Belling BEL IHT60 - page 13

    USING THE HOB detect, especially small pans (e.g. milk pans). W e recommend that you buy pans that are marked/advertised as being suit - able for induction. This problem is not with induction hob but with the pan type, they can have bases which are magnetic but are not thick enough! If you experience problems with small pans we recommend that you t ...

  • Belling BEL IHT60 - page 14

    USING THE HOB Power Level Maximum Operation Time hours 1 8 2 6 3 5 4 5 5 4 6 1.5 7 1.5 8 1.5 9 1.5 P (Power Boost) Max 5mins Energy Saving Tips Always place cookwar e on the cooking zone before it is switched on. When ever possible place lids on pans. TROUBLESHOOTING The hob produces a smell the rst few times it is used Heat a pan full of water ...

  • Belling BEL IHT60 - page 15

    CLEANING ELECTRIC HOB Ceramic glass hobs • It is recommended that you clean and wash the hob surface bef ore using for the rst time. Apply a thin coat of ceramic hob cleaner to the hob to help maintain and protect it. • The ceramic hob top can be cleaned using a clean, damp cloth or kitchen paper . Do not use a used dishcloth or sponge as th ...

  • Belling BEL IHT60 - page 16

    INSTALLATION Do Not Do not expose this product to contamina- tion by dust, building debris, sawdust etc, it is recommended that this product is stored in a clean environment until ready to install. Before installation any dust, building debris, sawdust etc should be vacuumed away to ensure no contamination will enter the unit. F ailure to follow th ...

  • Belling BEL IHT60 - page 17

    INSTALLATION CHOOSING YOUR INSTALLATION Make sure that the air inlets through the ventilator grids underneath the hob are never blocked. W e recommend that you install this ap- pliance in a work top which is a minimum 38mm deep. The hob can be tted into a work top less than 38mm deep, but the 20mm gap between hob base and appliance must be maint ...

  • Belling BEL IHT60 - page 18

    INSTALLATION Clearances and dimension – require- ments No shelf or overhang of combustible ma- terial should be closer than 650mm above the hob. There must be a minimum clearance of 50mm between the edges of the hob and any side walls; this clear ance must be maintained up to 420mm above the work top. There must be a minimum clearance of 50mm bet ...

  • Belling BEL IHT60 - page 19

    INSTALLATION Fitting into work top Cut a hole in the work surface to the required size. A clearance of at least 50mm should be maintained between the cutout and any rear or side wall. The work top must be of heat-resistant material or covered with heat -resistant material. Protecting the cut-out; The types of chipboard used for work surfaces swell ...

  • Belling BEL IHT60 - page 20

    INSTALLATION Fixing Bracket Advice Dealing with sides, cross-rails and back-panels in the cabinet. Depending on the cabinets, the work - top thickness and the hob positioning, it is possible for the hob base and/or the clamp brackets to interf ere with parts of the cabinet. Cut away cabinet and use appr opriate x - ing brackets f or your install ...

  • Belling BEL IHT60 - page 21

    INSTALLATION MAINS CABLE BRIDGES CABLE CLAMP Wire Colour Connect to: Live Brown L2 Neutral Blue N2 Earth Y ellow/ green Wire Colour Connect to: L1 Black L1 L2 Brown L2 Neutral Blue N2 Earth Y ellow/ green by excessive tightening or un-tightening. The use of power tools for this procedure is not recommended. Single Phase Option 3 Phase Option Remov ...

  • Belling BEL IHT60 - page 22

    TECHNICAL DATA SINGLE PHASE SUPPLY: 220 -240V ~ 50Hz 7.4kW 3 PHASE SUPPLY: 230 / 400V 3N ~ 50Hz Individual Cook Zone Power Ratings Cook Zone Normal Power/Boost Power Rating kW LHF 1.4/1.85 LHR 1.4/1.85 RHR 1.4/1.85 RHF 1.4/1.85 ...

  • Belling BEL IHT60 - page 23

    CUSTOMER CARE 15.030 CUSTOMER CARE WEB SHOP Having purchased a superior cooker , hob or hood from us, you’ll naturally want to keep it looking great. And who better to help you care for it than the manuf ac- turer? W e offer an extensive r ange of accesso- ries, components and cleaning products which, will instantly give your cooker a good as new ...

  • Belling BEL IHT60 - page 24

    17 .010 CUSTOMER CARE T o contact Belling about your appliance, please call Warranty Registration 0844 481 0182 to register your appliance Customer Care Helpline 0844 815 3746 in case of difculty within the UK Alternatively general, spar es and service information is available f rom our website at www.belling.co.uk Please ensure that you hav e t ...

Manufacturer Belling Category Stove

Documents that we receive from a manufacturer of a Belling BEL IHT60 can be divided into several groups. They are, among others:
- Belling technical drawings
- BEL IHT60 manuals
- Belling product data sheets
- information booklets
- or energy labels Belling BEL IHT60
All of them are important, but the most important information from the point of view of use of the device are in the user manual Belling BEL IHT60.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Belling BEL IHT60, service manual, brief instructions and user manuals Belling BEL IHT60. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Belling BEL IHT60.

Similar manuals

A complete manual for the device Belling BEL IHT60, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Belling BEL IHT60 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Belling BEL IHT60.

A complete Belling manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Belling BEL IHT60 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Belling BEL IHT60, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Belling BEL IHT60, that we can find in the current document
3. Tips how to use the basic functions of the device Belling BEL IHT60 - which should help us in our first steps of using Belling BEL IHT60
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Belling BEL IHT60
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Belling BEL IHT60 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Belling BEL IHT60?

Use the form below

If you did not solve your problem by using a manual Belling BEL IHT60, ask a question using the form below. If a user had a similar problem with Belling BEL IHT60 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)