English dropdown-ico

Manual Husqvarna 336

40 pages 2.33 mb
Download

Go to site of 40

Summary
  • Husqvarna 336 - page 1

    E E E E n n n n g g g g l l l l i i i i s s s s h h h h 336 EP A I Oper ator’ s manual Please r ead the operator’ s manual car efully and mak e sure y ou understand the instructions before using the machine. ...

  • Husqvarna 336 - page 2

    2 – English KEY T O SYMBOLS Symbols on the mac hine: W ARNING! Chain saws can be dangerous! Careless or improper use can result in serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alwa ys wear : • Approv ed protective helme ...

  • Husqvarna 336 - page 3

    English – 3 CONTENTS Contents KEY T O SYMBOLS Symbols on the machine: .............................................. 2 Symbols in the operator’ s manual: ................................ 2 CONTENTS Contents ....................................................................... 3 INTR ODUCTION Dear customer! .................................... ...

  • Husqvarna 336 - page 4

    4 – English INTR ODUCTION Dear customer! Cong ratulations on y our choice to buy a Husqv ar na product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River , for production of m uskets . The location was logical, since w ater power w as ...

  • Husqvarna 336 - page 5

    English – 5 WHA T IS WHA T? What is what on the c hain saw? 3 4 14 15 16 30 18 19 20 21 22 1 26 29 23 24 27 28 25 17 6 8 10 12 5 7 2 9 13 11 31 32 1 Filter cov er 2 Air purge 3 F ront handle 4 F ront hand guard 5 Star ter 6 Chain oil tank 7 Star ter handle 8 Adjuster screws carb uretor 9 Choke control Choke control/Start throttle lock W orking po ...

  • Husqvarna 336 - page 6

    6 – English GENERAL SAFETY PRECA UTIONS Bef ore using a new c hain saw • Please read this manual carefully . • Check that the cutting equipment is correctly fitted and adjusted. See instructions under the heading Assembly . • Refuel and star t the chain saw . See the instr uctions under the headings Fuel Handling and Star ting and Stopping ...

  • Husqvarna 336 - page 7

    English – 7 GENERAL SAFETY PRECA UTIONS chain sa w usage if possible . Y our dealer , f orestr y school or your libr ar y can provide inf or mation about which training materials and courses are av ailable . W ork is constantly in progress to improv e the design and technology - improv ements that increase your safety and efficiency . Visit your ...

  • Husqvarna 336 - page 8

    8 – English GENERAL SAFETY PRECA UTIONS • The chain brak e (A) can either be activated man ually (by your left hand) or automatically b y the iner tia release mechanism. • The brak e is applied when the front hand guard (B) is pushed f orwards . • This mov ement activates a spring-loaded mechanism that tightens the brak e band (C) around th ...

  • Husqvarna 336 - page 9

    English – 9 GENERAL SAFETY PRECA UTIONS Will m y hand alwa ys activate the chain brake during a kickbac k? No . It takes a certain force to mov e the hand guard forward. If your hand only lightly touches the front guard or slips o v er it, the f orce ma y not be enough to trigger the chain brake . Y ou should also maintain a firm gr ip of the ch ...

  • Husqvarna 336 - page 10

    10 – English GENERAL SAFETY PRECA UTIONS Cutting hardwoods (most broadleaf trees) creates more vibration than cutting softwoods (most conif ers). Cutting with cutting equipment that is blunt or f aulty (wrong type or badly shar pened) will increase the vibration le vel. Stop switc h Use the stop s witch to switch off the engine. Muffler The muf? ...

  • Husqvarna 336 - page 11

    English – 11 GENERAL SAFETY PRECA UTIONS Cutting equipment designed to minimise kickbac k The only wa y to av oid kickbac k is to make sure that the kickbac k zone of the bar nev er touches anything. By using cutting equipment with ”built-in” kickbac k reduction and keeping the chain sharp and well-maintained you can reduce the eff ects of ki ...

  • Husqvarna 336 - page 12

    12 – English GENERAL SAFETY PRECA UTIONS When you sharpen a cutting tooth there are four important f actors to remember . 1 Filing angle 2 Cutting angle 3 File position 4 Round file diameter It is very difficult to shar pen a chain correctly without the right equipment. W e recommend that you use our file gauge . This will help you obtain the ...

  • Husqvarna 336 - page 13

    English – 13 GENERAL SAFETY PRECA UTIONS • Place the depth gauge tool ov er the chain. Detailed inf ormation regarding the use of the depth gauge tool, will be f ound on the package f or the depth gauge tool. Use the flat file to file off the tip of the depth gauge that protrudes through the depth gauge tool. The depth gauge setting is corre ...

  • Husqvarna 336 - page 14

    14 – English GENERAL SAFETY PRECA UTIONS Checking c hain lubrication • Check the chain lubrication each time you refuel. See instructions under the heading Lubr icating the bar tip sprock et. Aim the tip of the bar at a light coloured surf ace about 20 cm (8 inches) aw a y . After 1 minute running at 3/4 throttle you should see a distinct line ...

  • Husqvarna 336 - page 15

    English – 15 GENERAL SAFETY PRECA UTIONS Bar Check regularly: • Whether there are burrs on the edges of the bar . Remov e these with a file if necessar y . • Whether the groov e in the bar has become badly wor n. Replace the bar if necessar y . • Whether the tip of the bar is une ven or badly w orn. If a hollow f or ms on the underside of ...

  • Husqvarna 336 - page 16

    16 – English ASSEMBL Y Fitting the bar and c hain Check that the chain br ake is in disengaged position b y moving the front hand guard to wards the front handle . Remov e the bar nuts and remove the clutch co v er (chain brak e). T ake off the transportation r ing (A). Fit the bar ov er the bar bolts. Place the bar in its rear most position. Pla ...

  • Husqvarna 336 - page 17

    English – 17 FUEL HANDLING Fuel Note! The machine is equipped with a two-stroke engine and must alwa ys been run using a mixture of gasoline and two- stroke engine oil. It is impor tant to accurately measure the amount of oil to be mix ed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, e ven small inaccuracies c ...

  • Husqvarna 336 - page 18

    18 – English FUEL HANDLING Fueling Clean the area around the fuel cap . Clean the fuel and chain oil tanks regularly . The fuel filter must be replaced at least once a year . Contamination in the tanks causes malfunction. Make sure the fuel is w ell mix ed by shaking the container bef ore refuelling. The capacities of the chain oil tank and fuel ...

  • Husqvarna 336 - page 19

    English – 19 ST AR TING AND ST OPPING Starting and stopping Cold engine Starting: The chain brak e should be activ ated when star ting the chain saw . Activate the chain brak e by pushing the front hand guard f orwards . Ignition: Set the stop s witch to the star t position. Choke: Set the choke control in the chok e position. Primer b ulb: Press ...

  • Husqvarna 336 - page 20

    20 – English ST AR TING AND ST OPPING Note! Pull the front hand guard to wards the front handle. The chain brak e is now disengaged. Y our saw is ready f or use. • Ne ver start a chain saw unless the bar , chain and clutch cov er are fitted correctly . See instructions under the heading Assembly . Without a bar and chain attached to the chain ...

  • Husqvarna 336 - page 21

    English – 21 W ORKING TECHNIQUES Bef ore use: 1 Check that the chain br ake w orks correctly and is not damaged. 2 Check that the rear right hand guard is not damaged. 3 Check that the throttle loc k wor ks correctly and is not damaged. 4 Check that the stop s witch works correctly and is not damaged. 5 Check that all handles are free from oil. 6 ...

  • Husqvarna 336 - page 22

    22 – English W ORKING TECHNIQUES 5 T ake great care when cutting a tree that is under tension. A tree that is under tension ma y spring back to its normal position bef ore or after being cut. If you position y ourself incorrectly or make the cut in the wrong place the tree ma y hit you or the machine and cause y ou to lose control. Both situation ...

  • Husqvarna 336 - page 23

    English – 23 W ORKING TECHNIQUES 7 T ake great care when you cut with the top edge of the bar , i.e. when cutting from the underside of the object. This is known as cutting with a pushing chain. The chain tries to push the chain saw bac k towards the user . If the saw chain is jamming, the saw ma y be pushed back at you. 8 Unless the user resists ...

  • Husqvarna 336 - page 24

    24 – English W ORKING TECHNIQUES Limbing When limbing thic k branches y ou should use the same approach as f or cutting. Cut difficult branches piece b y piece. Cutting If you ha ve a pile of logs, each log y ou attempt to cut should be remov ed from the pile, placed on a saw horse or runners and cut individually . Remov e the cut pieces from th ...

  • Husqvarna 336 - page 25

    English – 25 W ORKING TECHNIQUES T ree felling tec hnique Safe distance The saf e distance between a tree that is to be f elled and any one else working nearby is at least 2 1/2 tree lengths . Make sure that no-one else is in this ”risk zone” before or during felling. Felling direction The aim is to f ell the tree in a position where you can ...

  • Husqvarna 336 - page 26

    26 – English W ORKING TECHNIQUES Felling F elling is done using three cuts. First you make the directional cuts, which consist of the top cut and the bottom cut, then y ou finish with the f elling cut. By placing these cuts correctly you can control the f elling direction very accurately . Directional cuts T o make the directional cuts you begin ...

  • Husqvarna 336 - page 27

    English – 27 W ORKING TECHNIQUES W e recommend that you use a bar that is longer than the diameter of the tree, so that y ou can make the f elling cut and directional cuts with single cutting strokes . See instructions under the heading T echnical data section to find out which lengths of bar are recommended f or your sa w . There are methods f ...

  • Husqvarna 336 - page 28

    28 – English W ORKING TECHNIQUES How to a v oid kic kbac k What is kic kbac k? The word kic kback is used to describe the sudden reaction that causes the chain saw and bar to jump off an object when the upper quadrant of the tip of the bar , known as the kic kback zone , touches an object. Kickbac k always occurs in the cutting plane of the bar . ...

  • Husqvarna 336 - page 29

    English – 29 MAINTENANCE General The user must only carry out the maintenance and ser vice work described in this manual. Carb uretor adjustment Due to e xisting environmental and emissions legislation y our chain saw is equipped with mo v ement limiters on the carburetor adjuster scre ws. These limit the adjustment possibilities to a maximum of ...

  • Husqvarna 336 - page 30

    30 – English MAINTENANCE High speed jet H At the factory the engine is adjusted at sea level. When working at a high altitude or in diff erent weather conditions, temperatures and atmospheric humidity , it may be necessary to make minor adjustments to the high speed jet. CA UTION! If the high speed jet is screwed in too far , it may dama ge the p ...

  • Husqvarna 336 - page 31

    English – 31 MAINTENANCE Checking the brake trig ger Place the chain sa w on firm ground and star t it. Make sure the chain does not touch the ground or any other object. See the instructions under the heading Star t and stop. Grasp the chain sa w firmly , wrapping your fingers and thumbs around the handles. Apply full throttle and activate th ...

  • Husqvarna 336 - page 32

    32 – English MAINTENANCE Stop switc h Star t the engine and make sure the engine stops when y ou mov e the stop switch to the stop setting. Muffler Ne ver use a machine that has a f aulty muffler . Regularly check that the muffler is securely attached to the machine. Some mufflers are equipped with a special spark arrestor mesh. If your machi ...

  • Husqvarna 336 - page 33

    English – 33 MAINTENANCE • Undo the screw in the centre of the pulle y and remove the pulley . Inser t and f asten a new starter cord to the pulley . Wind appro x. 3 tur ns of the star ter cord onto the pulle y . Connect the pulley to the recoil spring so that the end of the spring engages in the pulley . Fit the screw in the center of the pull ...

  • Husqvarna 336 - page 34

    34 – English MAINTENANCE Spark plug The spark plug condition is influenced by: • Incorrect carburetor adjustment. • An incorrect fuel mixture (too much or incorrect type of oil). • A dir ty air filter . These f actors cause deposits on the spark plug electrodes, which ma y result in operating prob lems and star ting difficulties. If the ...

  • Husqvarna 336 - page 35

    English – 35 MAINTENANCE Maintenance sc hedule The f ollowing is a list of the maintenance that m ust be performed on the machine. Most of the items are descr ibed in the Maintenance section. Daily maintenance W eekly maintenance Monthly maintenance Clean the outside of the machine . On chain saws without a catalytic conv er ter , check the cooli ...

  • Husqvarna 336 - page 36

    36 – English TECHNICAL D A T A T echnical data 336 Engine Cylinder displacement, cu.in/cm 3 2,15/35,2 Cylinder bore, inch/mm 1,50/38,0 Stroke , inch/mm 1,22/31 Idle speed, r pm 2800 P ower , kW/ r pm 1,5/9600 Ignition system Manuf acturer of ignition system SEM T ype of ignition system CD Spark plug NGK BPMR 7A/ Champion RCJ 7Y Electrode gap , in ...

  • Husqvarna 336 - page 37

    English – 37 TECHNICAL D A T A Recommended original and replacement bar and c hain combinations F ollowing is a list of recommended cutting equipment f or the Husqvarna chain saw model 336. The combinations of power head, bar and chain hav e been tested and found to be in accordance with the kic kback and vibration requirements of ANSI B 175.1– ...

  • Husqvarna 336 - page 38

    38 – English FEDERAL EMISSION CONTR OL W ARRANTY ST A TEMENT ´®z+R.e¶5/¨ ´®z+R.e¶5/¨ Y OUR W ARRANTY RIGHTS AND OBLIGA TIONS The EP A (The US Environmental Protection Agency), Environment Canada and Husqv ar na F orest & Garden are pleased to e xplain the emissions control system w arranty on your 2001 and later small nonroad engine . ...

  • Husqvarna 336 - page 39

    English – 39 AMERICAN ST AND ARD SAFETY PRECA UTIONS Safety precautions f or chain saw users (ANSI B 175.1-2000 Anne x C) Kic kback saf ety precautions With a basic understanding of kic kback, you can reduce or eliminate the element of sur prise. Sudden surpr ise contributes to accidents. K eep a good fir m grip on the saw with both hands, the r ...

  • Husqvarna 336 - page 40

    ´®z+R.e¶5/¨ 2006-01-16 ´®z+R.e¶5/¨ 1150146-95 ...

Manufacturer Husqvarna Category Chainsaw

Documents that we receive from a manufacturer of a Husqvarna 336 can be divided into several groups. They are, among others:
- Husqvarna technical drawings
- 336 manuals
- Husqvarna product data sheets
- information booklets
- or energy labels Husqvarna 336
All of them are important, but the most important information from the point of view of use of the device are in the user manual Husqvarna 336.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Husqvarna 336, service manual, brief instructions and user manuals Husqvarna 336. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Husqvarna 336.

Similar manuals

A complete manual for the device Husqvarna 336, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Husqvarna 336 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Husqvarna 336.

A complete Husqvarna manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Husqvarna 336 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Husqvarna 336, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Husqvarna 336, that we can find in the current document
3. Tips how to use the basic functions of the device Husqvarna 336 - which should help us in our first steps of using Husqvarna 336
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Husqvarna 336
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Husqvarna 336 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Husqvarna 336?

Use the form below

If you did not solve your problem by using a manual Husqvarna 336, ask a question using the form below. If a user had a similar problem with Husqvarna 336 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)