English dropdown-ico

Manual Toshiba S2T

8 pages 0.16 mb
Download

Go to site of 8

Summary
  • Toshiba S2T - page 1

    Programmable Controllers Rev 051115 Ethernet Setup for the S2T Ethernet communications with the S2T CPU is done through the GEN651A Ethernet module. Prior to using this module, it must be confi gured using the EtherSetup_E setup software. The EtherSetup_E software is used to configure the network parameters (IP Address, Subnet Mask, and Multicast A ...

  • Toshiba S2T - page 2

    Page 2 2.6 Click the Option button. Set the required parameters, then click the Write button to write into GEN651A module. 2.7 Close the EtherSetup_E software. DIP S witches 7 and 8 must be left in the ON position for T-PDS to work through the GEN651A module. 2.8 Cycle Power on the GEN651A module. The new IP address will not be valid until power is ...

  • Toshiba S2T - page 3

    Page 3 Computer Ethernet Card Setup: The computer’s Ethernet card must be setup first. Go to the Control Panel and double click on Network C onnections. Find the Ethernet card, alternate click on it and then click on Properties. Note that the IP Address and Subnet Mast must be the same as set in T-PDS & the GEN651A (the last digit of the IP A ...

  • Toshiba S2T - page 4

    Page 4 T-PDS Setup: In T-PDS under the Option Menu, select Communications. Set as follows: Using T-PDS, set the following in special register SW63: This completes the T-PDS setup. T-PDS can now be connected to the S2E via Ethernet through the GEN651A Ethernet module. Note: If an attempt is made to assign an IP address in T-PDS be fore the computer? ...

  • Toshiba S2T - page 5

    Page 5 UDP/IP Socket Interface: To use UDP/IP transmission, it is necessary to create a small program in the S2T. The program will utilize the SEND and RE CV instructions. The general procedure is as follows: 1. Execute UDP socket open: The Specified Po rt number must be different from the Port number for T-PDS connection. If the Port num ber for T ...

  • Toshiba S2T - page 6

    Page 6 UDP Send: SEND instruction is used. ▬ [ A SEND B ] ▬ A : H3100 (fixed) B : Result status A+1 : UDP send command (H0032) B+1 : Error code A+2 : Socket number (1 to 12) A+3 : Receiver IP address (note 1) A+4 : Ditto A+5 : Receiver Port number A+6 : Transmit data word size (1 to 1000) A+7 : Source data table register type (note 2) A+8 : Sou ...

  • Toshiba S2T - page 7

    Page 7 UDP Receive: RECV instruction is used, ▬ [ A RECV B ] ▬ A : H3100 (fixed) B : Result status A+1 : UDP receive command (H0033) B+1 : Error code A+2 : Socket number (1 to 12) A+3 : Sender IP address (note 1) A+4 : Ditto A+5 : Sender Port number A+6 : Receive data word size (1 to 1000) A+7 : Destination data table register type (note 2) A+8 ...

  • Toshiba S2T - page 8

    Page 8 When R0621 is set to ON, 100 data words are received from the sender (IP address = 192.0.0.5, Port number = 5000) and are stored in D2000 to D2099. When the operation is finished, R0621 is reset to OFF automatically. UDP Socket Close SEND instruction is used. [ A SEND B ] ▬ A : H3100 (fixed) B : Result status A+1 : UDP close command (H0034 ...

Manufacturer Toshiba Category Network Card

Documents that we receive from a manufacturer of a Toshiba S2T can be divided into several groups. They are, among others:
- Toshiba technical drawings
- S2T manuals
- Toshiba product data sheets
- information booklets
- or energy labels Toshiba S2T
All of them are important, but the most important information from the point of view of use of the device are in the user manual Toshiba S2T.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Toshiba S2T, service manual, brief instructions and user manuals Toshiba S2T. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Toshiba S2T.

Similar manuals

A complete manual for the device Toshiba S2T, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Toshiba S2T by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Toshiba S2T.

A complete Toshiba manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Toshiba S2T - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Toshiba S2T, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Toshiba S2T, that we can find in the current document
3. Tips how to use the basic functions of the device Toshiba S2T - which should help us in our first steps of using Toshiba S2T
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Toshiba S2T
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Toshiba S2T in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Toshiba S2T?

Use the form below

If you did not solve your problem by using a manual Toshiba S2T, ask a question using the form below. If a user had a similar problem with Toshiba S2T it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)