English dropdown-ico

Manual Thermo Products USDT 2004B

10 pages 0.48 mb
Download

Go to site of 10

Summary
  • Thermo Products USDT 2004B - page 1

    USDT 2004B Installation and User’s Guide Introduction General Information 2 Installation Collector Sensor 3 Control Box 5 Power Connection 6 Display Window 6 Operation Basic Operation of Digital Display 6 Program ming the Temperature Range 8 Manual Operation Mode 9 Troubleshooting 10  Thermo Technologies 5560 Sterrett Place • Suite 115 Colum ...

  • Thermo Products USDT 2004B - page 2

    2 Introduction Note: The information supplied in this manual is for guidance only - no part of this may be used for any agreement, whether express or implied, or to form any contract. Thermo Technologies reserves the right to change specifications without prior notice. SDT 2004B is a powerful temperature differential control unit. It uses two tempe ...

  • Thermo Products USDT 2004B - page 3

    3 INSTALLATION Note: This installation procedure is for guidance only, and the installer should verify its suitability. Make sure that the solar system is physically installed, manually tested, and ready for controlled operation. he following safety precautions is strongly recommended: 1. Before attempting to install and operate the unit read this ...

  • Thermo Products USDT 2004B - page 4

    4 l Collector sensor (red cable with protective terminal box): Either push into a thermowell, (sensor pocket), which is soldered or riveted directly to the manifold (vacuum tubes). Alternately, strap the sensor to the collector outlet pipe or the absorber ( flat plate collectors) that projects from the collector housing. Ideally, house the collecto ...

  • Thermo Products USDT 2004B - page 5

    5 Undo the screw at the top of the housing. The control elec tronics are mounted on the enclosure cover. The controller enclosure can be screwed to the wall with cable entry grommets pointed downwards. Use the supplied plastic bridges to secure power and sensor cables. Base of the unit to be mounted at eye - leve l and wired as shown above Caution: ...

  • Thermo Products USDT 2004B - page 6

    6 ower Connections: A small blade screwdriv er may be used to fasten miniaturized terminal block screws while the corresponding wire is inserted. NOTE 1: Always disconnect the controller from power supply before opening the housing. NOTE 2: The controller should be properly grounded. Flexible w ires, 18/3 AWG (gauge/conductor) simplify connection t ...

  • Thermo Products USDT 2004B - page 7

    7 ò Push selection key once to enter the advanc ed (Par or *Men) mode. Once in selected mode, press one more time to select the parameter in that mode. Selected parameter blinks allowing the user to modify it. You can modify the selected parameter while the middle window blinks by pressing the ï or ð ke y. ñ Push selection key once to accept se ...

  • Thermo Products USDT 2004B - page 8

    8 Par Using the navigation key ^_ allows you to select the desired parameter while you are in the program mode. Press the selection key ò once to select the parameter in the window. Selected parameter blinks allowing you to modify it. You can modify the selected parameter while the middle window blinks by pressing the ï or ð key. The unit accept ...

  • Thermo Products USDT 2004B - page 9

    9 Ma nual Operation Mode This mode allows the user to manually turn the pump on or off. AUTO The above display indicates that the unit is working in automatic mode. The pump starts at a temperature difference of 15 o F and runs as long as ? T is above 7 o F. The B symbol appears in upper display line next to the collector symbol while the pump is r ...

  • Thermo Products USDT 2004B - page 10

    10 T roubleshooting In general, all of the settings in the menus Par and Men and the terminal should first be checked if there is a malfunction. Malfunction, but "realistic" temperature values: • Check program number. It should be “0” (zero) for 2004B unit. • Check the switch - on and switch - off thresholds and the set differenti ...

Manufacturer Thermo Products Category Stud Sensor

Documents that we receive from a manufacturer of a Thermo Products USDT 2004B can be divided into several groups. They are, among others:
- Thermo Products technical drawings
- USDT 2004B manuals
- Thermo Products product data sheets
- information booklets
- or energy labels Thermo Products USDT 2004B
All of them are important, but the most important information from the point of view of use of the device are in the user manual Thermo Products USDT 2004B.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Thermo Products USDT 2004B, service manual, brief instructions and user manuals Thermo Products USDT 2004B. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Thermo Products USDT 2004B.

Similar manuals

A complete manual for the device Thermo Products USDT 2004B, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Thermo Products USDT 2004B by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Thermo Products USDT 2004B.

A complete Thermo Products manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Thermo Products USDT 2004B - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Thermo Products USDT 2004B, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Thermo Products USDT 2004B, that we can find in the current document
3. Tips how to use the basic functions of the device Thermo Products USDT 2004B - which should help us in our first steps of using Thermo Products USDT 2004B
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Thermo Products USDT 2004B
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Thermo Products USDT 2004B in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Thermo Products USDT 2004B?

Use the form below

If you did not solve your problem by using a manual Thermo Products USDT 2004B, ask a question using the form below. If a user had a similar problem with Thermo Products USDT 2004B it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)