-
Polycom EX, FX, VS4000 - page 1
Integrators’ Reference Manual For ViewStation ® EX, ViewStation ® FX, and VS4000 March 2003 Edition 3725-20771-001 Revision A ...
-
Polycom EX, FX, VS4000 - page 2
Trademark Information Polycom® and the Polycom logo design are registered tr ademarks of Polycom Inc. ARENA™, Global Manag ement System™, ImageShare™, iPower™, LimeLight™, MGC Manager™, PathNavigator™, Polycom Office™, Polycom OneDial™, ViewStation™, ViaVideo™, Visual Concert DC™, Visual Concert FX™, Visual Concert PC™, ...
-
Polycom EX, FX, VS4000 - page 3
© Polycom, Inc. i Contents Chapter 1 - About this Manual ........ .............. ............. ............. 1 Conventions Used in this Manual ............ .............. ............... .............. .............. .............. . 2 Glossary ........ ............... .............. .............. .............. ........... .............. ....... ...
-
Polycom EX, FX, VS4000 - page 4
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 ii www.polycom.com Capacity Planning ................ .............. .............. .............. .............. .............. .............. . 53 Call Processing Considerations ........ .............. ................. .............. .............. ............ 54 Gat ...
-
Polycom EX, FX, VS4000 - page 5
Contents © Polycom, Inc. iii Installation .................. .............. .............. .............. .............. .............. .............. ..... 84 Installing a V.35/RS-449/RS-530 Network Interface Module ....................... ..... 85 Cables Used with the V.35/RS-449/RS -530 Network Interface Module ... 85 Installation ............. ...
-
Polycom EX, FX, VS4000 - page 6
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 iv www.polycom.com Medium and Large Room Systems ........... .............. .............. ........... ............. 128 Small Room Systems ................... ........... .............. .............. .............. .............. .. 130 Safety and Legal Notices ....... ...
-
Polycom EX, FX, VS4000 - page 7
© Polycom, Inc. v List of Figures Figure 2-1. RS-232 Cable for ViewStation EX an d FX ................... .............. ............ .......... 20 Figure 2-2. RS-232 Cable for VS 4000 ................. ................................................................... 21 Figure 2-3. Keyed RJ-45 Cable, System to Ne twork Interface Module ........ ...
-
Polycom EX, FX, VS4000 - page 8
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 vi www.polycom.com ...
-
Polycom EX, FX, VS4000 - page 9
© Polycom, Inc. vii List of Tables Table 2-1. Electrical and Physical Specifications ............... .............. .............. ........... ........ 12 Table 2-2. Connectivity ... .............. ............... .............. .............. .............. .............. .............. .. 1 3 Table 2-3. Video Standards Supported ........... .... ...
-
Polycom EX, FX, VS4000 - page 10
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 viii www.polycom.com Table 6-4. V.35/RS-449/RS-530 Indicator Lamps - Network Side ......... ...................... 112 Table 6-5. V.35/RS-449/RS-530 Indicator Lamps - Peripheral Side ...... ...................... 112 Table 6-6. Fault Isolation ................ .......... ...
-
Polycom EX, FX, VS4000 - page 11
© Polycom, Inc. 1 1 About this Manual This chapter provides information to help you use the rest of the manual. This manual covers the following topics: Topic Page Technical Informa tion 11 Before You Deploy 47 Installing Videoconferencing Systems 77 Supporting Advanced Users 97 Testing and Troubleshooting 109 ...
-
Polycom EX, FX, VS4000 - page 12
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 2 www.polycom.com Conventions Used in this Manual The following typographic conventions are used in this manual: ❑ Links that allow you to jump to other sections of this manual are blue . ❑ File path names and commands you type in command lines are shown in this font ...
-
Polycom EX, FX, VS4000 - page 13
Chapter 1 - About this Manual © Polycom, Inc. 3 ARJ H.323 Admission Reject Mess age. This message is from the Gatekeeper, rejecting the e ndpoint’s request to connect to another endpoint. ARQ H.323 Admission Request Message. This message is from an endpoint to the Gatekeeper requesting a connection to another endpoint. Automatic Voice Tracking A ...
-
Polycom EX, FX, VS4000 - page 14
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 4 www.polycom.com CIF Common Intermediate Format, also called FCIF. A video format providing resolution of 352 x 288 pixels. See also QCIF, 4CIF, 16CIF. Client A networked PC or term inal that shares services with other PCs. These services are provided by a server. Confe ...
-
Polycom EX, FX, VS4000 - page 15
Chapter 1 - About this Manual © Polycom, Inc. 5 Endpoint A site, videoconferencing system, gateway, or MCU. Ethernet 10 Mbps or 100 Mbps LAN technology based on CSMA/CD. Far End The party or parties to whom you place a call. Fast Ethernet 100 Mbps LAN technology based on CSMA/CD. FCIF Full CIF. See CIF. Firewall A network node set up as a boundary ...
-
Polycom EX, FX, VS4000 - page 16
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 6 www.polycom.com H.323 ITU-T videoconferencing standard for IP. H.323 includes the H.225, H. 245 , G.711, G.722, G.723.1, G.728, and G.729 standards. IMUX Inverse Multiplexer. See Quad BRI network interface module. IP Internet Protocol. A unique IP address identifies ev ...
-
Polycom EX, FX, VS4000 - page 17
Chapter 1 - About this Manual © Polycom, Inc. 7 NFAS Non-Facili ty Associated Sig nalling. NT-1 Network Termination type 1. The device that converts the ISDN BR I U interface from the telecommunications s ervice provider to the S/T interface used by ISDN products and sys tems. Pan Move the camera to the left or right. PBX Private Branch eXchange. ...
-
Polycom EX, FX, VS4000 - page 18
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 8 www.polycom.com QoS Quality of Se rvice. This allow s guaranteed bandwidth and packet de livery between endpoints over a packet network. RAI Remote Alarm Indication. RJ-11 A six-conductor modu lar jack. RJ-11 connectors are used on all standard telephones in the US for ...
-
Polycom EX, FX, VS4000 - page 19
Chapter 1 - About this Manual © Polycom, Inc. 9 WAN Wide Area Network. Busine ss with LANs at more than one location may use the public carrier network to carry data between these locations. Typical WAN services provided by the pubic carrier are Frame Relay, X.25, and ISDN for carrying data. Whiteboard Software that al lows you to share and annota ...
-
Polycom EX, FX, VS4000 - page 20
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 10 www.polycom.com ...
-
Polycom EX, FX, VS4000 - page 21
© Polycom, Inc. 11 2 Technical Information This chapter provides descriptions and technical information about the ViewStation EX, ViewStation FX, and VS4000 systems. This chapter covers the follow ing topics. Topic Page System Descriptions 12 Other Eleme nts of a Ty pical Deplo yment 45 ...
-
Polycom EX, FX, VS4000 - page 22
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 12 www.polycom.com System Descriptions The Polycom ViewStation EX an d ViewStation F X systems are set-top videoconferencing syst ems designed for conference rooms. The Polycom VS4000 system is a rack-mounted videoconferencing system designed for large conference rooms o ...
-
Polycom EX, FX, VS4000 - page 23
Chapter 2 - Technical Information © Polycom, Inc. 13 The following table describes the network interfaces available. ViewStation EX, ViewStation FX, and VS4000 are Cisco AVVID certified. Table 2-2. Connectivity Network interface Connectivity provided LAN/WAN Supports—TCP/IP, DNS, WINS, SNMP, DHCP, ARP, WWW, FTP, Telnet (2) 10/100 Mbps Ethernet p ...
-
Polycom EX, FX, VS4000 - page 24
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 14 www.polycom.com The following table lists th e supported video standards. The following table gives information about the video sign al formats. Table 2-3. Video Standards Suppo rted Standard Supported Videoconferencing H.32 0 p x 64 H.323 Video standard s H.261 + Ann ...
-
Polycom EX, FX, VS4000 - page 25
Chapter 2 - Technical Information © Polycom, Inc. 15 The following table gives electrical specifications f or the video inputs and ou tputs. The following table g ives other video specifications for the ViewStation EX, ViewStation FX, and VS4000 systems. Table 2-5. Video Input/Outp ut Electrical Specification s Parameter Value/format Impedance 75 ...
-
Polycom EX, FX, VS4000 - page 26
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 16 www.polycom.com The following table gives camera and display inf ormation. The following table gives electrical specifications for the audio inputs and outputs. Table 2-7. Cameras and Displays Parameter ViewStation EX and FX VS4000 Main camera Integrated Sony EVI-10 E ...
-
Polycom EX, FX, VS4000 - page 27
Chapter 2 - Technical Information © Polycom, Inc. 17 The following table gives information about audio features. The following table gives information about the microphone pods supplied with the ViewStation EX, V iewStation FX, and VS4000 systems. Table 2-9. Audio Features Parameter Value/format Audio codecs a a. The protocol used depends on the p ...
-
Polycom EX, FX, VS4000 - page 28
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 18 www.polycom.com The following table g ives information about multipoi nt calling. Table 2-11. Call Capabilities Feature Capability Maximum data rate ViewStation EX: 768 Kbps ViewStation FX and VS4000: 2 Mbps Local plus three oth er sites ViewSta tion FX and VS4000: 38 ...
-
Polycom EX, FX, VS4000 - page 29
Chapter 2 - Technical Information © Polycom, Inc. 19 The following table gives information about the systems’ user interfaces. Table 2-12. User Interface Feature Capability Languages English, French , German, Spanish, Italian, Portuguese, Norwegian, Chin ese, Japanese Control system Hand-held, ergono mically designe d remote contro l Infrared re ...
-
Polycom EX, FX, VS4000 - page 30
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 20 www.polycom.com RS-232 Interface The RS-232 interface allows user s to connect a ViewStation EX, ViewStation FX, or VS4000 to a PC. This provides a means of access to the ARENA API, which allows users to automate some of the systems’ control feature s. Refer to the ...
-
Polycom EX, FX, VS4000 - page 31
Chapter 2 - Technical Information © Polycom, Inc. 21 Figure 2-2 shows the RS-232 cable for the VS4000 system. Figure 2-2. RS-232 Cable for VS4000 ...
-
Polycom EX, FX, VS4000 - page 32
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 22 www.polycom.com Quad BRI Network Interface Module The following paragraphs provide technical information abou t the Quad BRI network interface module available with the ViewStation EX, ViewStation FX, and VS4000 systems. If you do not connect the system to an internal ...
-
Polycom EX, FX, VS4000 - page 33
Chapter 2 - Technical Information © Polycom, Inc. 23 Quad BRI Cabling The Quad BRI network interface mo dule connects to the endpoint using a cable with one keyed RJ -45 connect or and one standard RJ-45 connector. Figure 2-3 shows th is cable. Because it uses a non-standard connector, Polycom In c. does not support cables of this type that are fa ...
-
Polycom EX, FX, VS4000 - page 34
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 24 www.polycom.com Standard RJ-45 to RJ-45 cables conne ct the Quad BR I to the network. Figure 2-4 shows this type of cable. Figure 2-4. Standard RJ-45 Cable, Networ k Interface Module to Network NT-1 Information Following are sample NT-1 settings. For more detailed dia ...
-
Polycom EX, FX, VS4000 - page 35
Chapter 2 - Technical Information © Polycom, Inc. 25 ISDN Switches Depending on the type of ISDN lines you are using, your service provider may assign zero, one, or two SPIDs per line. Refer to Table 2-15 below. Automatic Quad BRI Software Update The Quad BRI is expected to have a software version at least as recent as that of the system to which ...
-
Polycom EX, FX, VS4000 - page 36
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 26 www.polycom.com PRI Network Interface Modu le for ViewStation FX and VS4000 The following paragraphs provide technical information abou t the T1 and E1 PRI network interface modules available with the ViewStation FX and VS4000. This ne twork interface module is not av ...
-
Polycom EX, FX, VS4000 - page 37
Chapter 2 - Technical Information © Polycom, Inc. 27 Indicators on the PRI Network Interface Module The tables below describe the expe cted be havior of the indicator lamps on the PRI network interface module. On the network si de, the expected behavior depends on wh ether it is a T1 module or an E1 module. Non-Facility Associated Signaling (NFAS) ...
-
Polycom EX, FX, VS4000 - page 38
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 28 www.polycom.com Indicator lamps on the peripheral side of the PRI network interface module have the same meanings for both the T1 and E1 models. Table 2-18. PRI Peripheral Side Indicator Lamps Indication Meaning Amber LED on The PRI network interface module is in boot ...
-
Polycom EX, FX, VS4000 - page 39
Chapter 2 - Technical Information © Polycom, Inc. 29 PRI Cabling The peripheral side of the PRI ne twork interface module connects to the endpoint using a cabl e with keyed RJ-45 connectors. Figure 2-5 shows this cabl e. Because it us es a non-standard connector, Polycom In c . do e s n ot s up p o r t c a bl e s of t h is t y p e t h at a r e f a ...
-
Polycom EX, FX, VS4000 - page 40
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 30 www.polycom.com Channel Selection For outgoing calls, the system us es the lowest-numbered available channel (1-23 for a PRI T1 and 1-30 for a PRI E1). If an additional channel is needed, the system chooses the next higher-numbered channel. For example , if channels 1 ...
-
Polycom EX, FX, VS4000 - page 41
Chapter 2 - Technical Information © Polycom, Inc. 31 V.35/RS-449/RS-530 Ne twork Interface Module The following paragraphs provide technical information abou t the V.35/RS-449/RS-530 networ k interface module available with the ViewStation EX, ViewStation FX, and VS4000. The system’s V.35/RS-449/RS-530 ne twork interface module is not interchang ...
-
Polycom EX, FX, VS4000 - page 42
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 32 www.polycom.com V.35/RS-449/RS-530 Cabling This section provide s cable drawings and pinouts for the three cables that you can use with the V.35/RS-449/RS-530 network interface module. All are common to the ViewStation EX, ViewStation FX, and VS4000. Figure 2-7. HD-44 ...
-
Polycom EX, FX, VS4000 - page 43
Chapter 2 - Technical Information © Polycom, Inc. 33 Figure 2-8. Pinout to the HD-44M to RS-366/V.35 “Y” Cable ...
-
Polycom EX, FX, VS4000 - page 44
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 34 www.polycom.com Figure 2-9. HD-44M to RS-449/RS-422 “Y” Cable Diagra m ...
-
Polycom EX, FX, VS4000 - page 45
Chapter 2 - Technical Information © Polycom, Inc. 35 Figure 2-10. Pinout to the HD-44M to RS-449/RS-422 “Y” Cable ...
-
Polycom EX, FX, VS4000 - page 46
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 36 www.polycom.com Figure 2-11. Ascend HD-44M to HD-44M Cable Diagram Figure 2-12. Pinout for the Ascend HD-44M to HD-44M Cable ...
-
Polycom EX, FX, VS4000 - page 47
Chapter 2 - Technical Information © Polycom, Inc. 37 Figure 2-13. RS-530 Cable Diagram and Pinout ...
-
Polycom EX, FX, VS4000 - page 48
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 38 www.polycom.com Serial Interface Control Signals If you need to customize your V.35/RS-449/RS-530 interface, use the signal information in Table 2-21 bel ow in addition to the information provided by your n etwork equipment ve ndor. Table 2-21. Serial Interface Contro ...
-
Polycom EX, FX, VS4000 - page 49
Chapter 2 - Technical Information © Polycom, Inc. 39 State Machine The V.35/RS-449/RS-530 state machine controls how the V.35/RS-449/RS-530 interface signal s handshake with the network interface equipment while the ca ll is being established. The following tables describe the machine states. Table 2-22. Di al-Out State Mach ine State ViewStation ...
-
Polycom EX, FX, VS4000 - page 50
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 40 www.polycom.com 15 RTS = 0 b DTR = 0 a CRQ = 0 All signals go low if Far End or User hang up is detected DSR = 1 to 0, OR DCD = 1 to 0 A falling edge on DSR or DCD are interpreted by the ViewStation FX or VS4000 as a hang-up 16 IDLE DTR = 0 a RTS = 0 b CRQ = 0 IDLE RI ...
-
Polycom EX, FX, VS4000 - page 51
Chapter 2 - Technical Information © Polycom, Inc. 41 5 DTR = 1 6 RTS = 1 b 7 Wait for DSR high 8 DSR = 1 AND/OR DCD = 1 (AND/OR DSR = 1 c ) 9 Go to connected state 10 DATA FLOW STARTS DATA FLOW STARTS 11 User Hang-up Far End Hang-up 12 RTS = 0 b DTR = 0 a CRQ = 0 All signals go low if Far End or User hang up is detected DSR= 1 to 0, OR DCD= 1 to 0 ...
-
Polycom EX, FX, VS4000 - page 52
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 42 www.polycom.com Table 2-24. Non-Dialed User-Initiated Call State Machin e State ViewStation FX or VS4000 Signals Network Signals 1 Initia l State: DTR = 0 a RTS = 0 b CRQ = 0 a. DTR does not act as sh own but remains high if DTR is set to ON in the V.35 Adva nced Setu ...
-
Polycom EX, FX, VS4000 - page 53
Chapter 2 - Technical Information © Polycom, Inc. 43 Table 2-25. No n-dialed Ne twork-Initia ted Call State Mach ine State ViewStation FX or VS4000 Signals Network Signals 1 Initia l State: DTR = 0 a RTS = 0 b CRQ = 0 a. DTR does not act as sh own but remains high if DTR is set to ON in the V.35 Advan ced Setup screen. b. RTS does not act as shown ...
-
Polycom EX, FX, VS4000 - page 54
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 44 www.polycom.com Crypto Resync If a cryptographic encoder/decoder is connected between the system and the network, it may re quire a resynchronization signal from the system. This is a signal indicating that the system has los t video synchronization due to a ne twork ...
-
Polycom EX, FX, VS4000 - page 55
Chapter 2 - Technical Information © Polycom, Inc. 45 Other Elements of a Typical Deployment A typical deployment includes some of the following Polycom equipment and software in addition to videoconferencing endpoints: ❑ MGC Manager™ ❑ Global Management System™ ❑ WebCommander™ ❑ PathNavigat or™ For more information, please re fer t ...
-
Polycom EX, FX, VS4000 - page 56
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 46 www.polycom.com ...
-
Polycom EX, FX, VS4000 - page 57
© Polycom, Inc. 47 3 Before You Deploy This chapter provides a summary of the deployment process, and describes what you must do to prepare for i nstallation. This chapter covers the follow ing topics. Topic Page Predeployment Overview 48 Video Network Security 49 Best Practices 50 Predeployment Pla nning 51 Developing the Dial Plan 55 ISDN Requir ...
-
Polycom EX, FX, VS4000 - page 58
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 48 www.polycom.com Predeployment Overview The diagram below gi ves an overview of the tasks i nvolved in predeployment planning. Figure 3-1. The Predeployment Process Document the netw ork: LANs Subnets WAN links Determine netw ork capacity requirements Speci ...
-
Polycom EX, FX, VS4000 - page 59
Chapter 3 - Before You Deploy © Polycom, Inc. 49 Video Network Security Polycom recommends the following general precautions to keep your video network secure: ❑ Deploy IP endpoints behind a firewall. ❑ If your deployment seldom re quires centralized management capabilities, disable all endp oints’ remote management capabilities. ❑ If your ...
-
Polycom EX, FX, VS4000 - page 60
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 50 www.polycom.com Best Practices Polycom recommends the following as best practices when deploying Pol ycom IP voice and video applications . ❑ Consider latency, jitter, and packet loss. All are obstacles to high quality audio and video. Table 3-1 below recommends max ...
-
Polycom EX, FX, VS4000 - page 61
Chapter 3 - Before You Deploy © Polycom, Inc. 51 Notes Older Polycom ViewStation systems and the RADVision MCUs and gateways both support 10 Mbps half duplex only. There are k nown iss ues with so me older Cisco Catalyst 10/100 switches and video endpoints negotiating half/full duplex. If the negotiation fails, the e ndpoi nt will still funct ion, ...
-
Polycom EX, FX, VS4000 - page 62
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 52 www.polycom.com LAN/WAN Considerations You will need to develop a network topology checklist that includes the following information: ❑ List of Networks: To take advantage of least cost routing and alternate routing, you must define the topology of the Local area ne ...
-
Polycom EX, FX, VS4000 - page 63
Chapter 3 - Before You Deploy © Polycom, Inc. 53 Capacity Planning H.323 traffic uses more bandwidth th an the selected call quali ty or H.320 equivalent. Polyc om re commends that you allow 20% overhead for the H.323 signaling traffic. ISDN networks do not include signaling in the payload calculations , but in TCP/IP networks all signaling must a ...
-
Polycom EX, FX, VS4000 - page 64
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 54 www.polycom.com Keep in mind that the examples given here discuss only a single point-to-point call. Your capacity planning calculations must take into account the total number of calls that you expect the net work to handle at one time, including multipoint call s. I ...
-
Polycom EX, FX, VS4000 - page 65
Chapter 3 - Before You Deploy © Polycom, Inc. 55 Gatekeeper Identifier You will need to specify the gatekeepe r identifier for each gatekeeper being deployed. You must also define the maximum number of endpoints that may be registered to each gatekee per and the maximum number of calls that each gatekeeper may handle at one time. Default Gatekeepe ...
-
Polycom EX, FX, VS4000 - page 66
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 56 www.polycom.com Service prefixes are short numer ic strings that identify the services being requested, such as call speed and zone. An H.323 dial plan allows you to associate a numeric alias to the network address of each H.323 entity. This is the calling plan that y ...
-
Polycom EX, FX, VS4000 - page 67
Chapter 3 - Before You Deploy © Polycom, Inc. 57 A well-designed dial plan di stributes the dial plan logic among the gateways and gatekeepers. Try to keep the dial plan logic at the highest component level — for example, allow the gatekeeper to handle routing and fa il-over decisions. This allows individual zones to be added or modified without ...
-
Polycom EX, FX, VS4000 - page 68
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 58 www.polycom.com Administration, Policies, and Routing Administration Plan The videoconferencing administra tion plan allows the system administrator to manage user permis sions and network poli cies. Your plan should define: ❑ Superusers ❑ Administrators ❑ Permi ...
-
Polycom EX, FX, VS4000 - page 69
Chapter 3 - Before You Deploy © Polycom, Inc. 59 If your organization has specia l rate plans, those should be incorporated into the least-cost routing tables. Network Topology You will need the networ k topology information descri bed in LAN/WAN Considerations on page 52 when you desi gn your dial plan and configure PathN avigator to manage your ...
-
Polycom EX, FX, VS4000 - page 70
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 60 www.polycom.com Addressing The addressing components of an H.323 dial plan are: ❑ Gatekeeper zone identifiers or prefixes ❑ Entity addressing ❑ Terminal aliases (include nu meric and alphabetic aliases) ❑ System Services ❑ MCU service prefixes ❑ Gateway se ...
-
Polycom EX, FX, VS4000 - page 71
Chapter 3 - Before You Deploy © Polycom, Inc. 61 If the local zone prefixes are configured, requests from neighbor gatekeepers with prefixes that match the local zone prefix will be resolved. All other calls will be rejected. Entity Addressing An entity must have a network address and may have alias addresses. These are defi ned as follows: ❑ Ne ...
-
Polycom EX, FX, VS4000 - page 72
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 62 www.polycom.com Rules for Assigning Prefixes and Numeric Aliases In assigning prefixes and numeric alia ses, it is critically important to observe certain rules: ❑ MCUs and gateways provide se rvices, so they must have service prefixes assigned to them. Each s ervic ...
-
Polycom EX, FX, VS4000 - page 73
Chapter 3 - Before You Deploy © Polycom, Inc. 63 System Services System services include the following: ❑ Conference on demand ❑ Call forwarding: set forward busy, set for ward no answer, and set forward unconditional. ❑ Access simplified diali ng ❑ Join or leave hunt group System services only work within a zone. They do not work across z ...
-
Polycom EX, FX, VS4000 - page 74
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 64 www.polycom.com The PRI T1 needs to be provisione d for the ViewStation FX and VS4000 systems as follows: Table 3-4. ISDN PRI Requirements Line settings ESF/B8ZS (default) Extended Super Frame B8ZS is modem st andard for T1/PRI line encoding and framing Line terminati ...
-
Polycom EX, FX, VS4000 - page 75
Chapter 3 - Before You Deploy © Polycom, Inc. 65 The PRI direct from the telephone service provider should support both data and voice for Polycom’s voice add-on capability of systems. Determining Usage To ge t th e b es t r a te of re tu rn f ro m P R I li n es , t he y s h ou ld be u se d a s much as possible. To do this, look at the data and ...
-
Polycom EX, FX, VS4000 - page 76
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 66 www.polycom.com Figure 3-2. Network Configuration (No PBX) Figure 3-3. Network Configuration (Behind PBX) For ISDN BRI lines to be used fr om a PBX to a videoconferencing system, you must do these things in addition to meeting the other requirements. ❑ Determine the ...
-
Polycom EX, FX, VS4000 - page 77
Chapter 3 - Before You Deploy © Polycom, Inc. 67 not you need an NT1 device between the PBX and the ISDN BRI interface of the videoconferencing system. ❑ If the ISDN BRI network module in the PBX is S/T-loop, there is a 500-foot limitation with S/T-loop ISDN. The module may still require a special jack with a resistor. ❑ Ensure that the ISDN P ...
-
Polycom EX, FX, VS4000 - page 78
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 68 www.polycom.com ❑ The ISDN BRI service must allow videoconferencing calls to be dialed on either B channel or on both simultaneously. ❑ The D channel should not permit X.25 packet data. ❑ The ISDN BRI service must be co nfigured as Te rminal Type A. ❑ The ISDN ...
-
Polycom EX, FX, VS4000 - page 79
Chapter 3 - Before You Deploy © Polycom, Inc. 69 ❑ If the distance is between 50 an d 250 feet , you must use a 9-volt AC/DC transformer to boost power (such as the Digi-Key #T405-ND). Connect the transfor mer to the Quad BRI network interface module. ❑ RJ-45 jacks, connected to 110 bl ocks or 66 blocks, should be installed in the wiring close ...
-
Polycom EX, FX, VS4000 - page 80
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 70 www.polycom.com The following tables show how the data modules should be configured in the Lucent Definity PBX administrative console. Ports 3 and 4 are configured identically with unique extensions for each module, and different port numbers. Table 3-5. Example Confi ...
-
Polycom EX, FX, VS4000 - page 81
Chapter 3 - Before You Deploy © Polycom, Inc. 71 Next, you must configure any required hunt groups with a direct inward dialing (DID) num bers, or local directory numbers. This enables other systems to call your system. Once you have configured the hunt groups, hook up the DCP ports to the system and follow the a ppropriate system installation pro ...
-
Polycom EX, FX, VS4000 - page 82
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 72 www.polycom.com Site Considerations When you select a site for videoconferencing equipment, consid er the following factors: Table 3-7. Site Conside rations Factor For best results Access to required connections Ensure that the equipment will be within 6 feet (1.8 m) ...
-
Polycom EX, FX, VS4000 - page 83
Chapter 3 - Before You Deploy © Polycom, Inc. 73 Acoustics and background noise Ensure that there is no audible echo in the room wher e the camera and microphone(s) will b e installed. Carpeting, drapery, a nd upholstered furnit ure all help to reduce echo problems. N on-rectangular rooms have less echo than standard conference rooms. Microphone p ...
-
Polycom EX, FX, VS4000 - page 84
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 74 www.polycom.com Predeployment Worksheet This worksheet will hel p you get the information you need to install videoconferencing systems on your company’s LAN computer network. Complete this worksheet before you start the installation. Once you have this information, ...
-
Polycom EX, FX, VS4000 - page 85
Chapter 3 - Before You Deploy © Polycom, Inc. 75 Extension (Terminal ID or E.164 number) for the videoconferencing system SNMP Information (if necessary) If you intend to ready your system for remote manage ment via Simple Network Management Protocol (S NMP), you also need to know: IP address for the network management station _______._______ .___ ...
-
Polycom EX, FX, VS4000 - page 86
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 76 www.polycom.com ...
-
Polycom EX, FX, VS4000 - page 87
© Polycom, Inc. 77 4 Installing Videoconferencing Systems This chapter provides installati on instructions for the ViewStation EX, ViewStation FX, and VS4000 and their network interface modules. This chapter covers the follow ing topics. Topic Page The Deployment Process 78 Installation Procedures 79 Network Configura tion 88 Connecting the System ...
-
Polycom EX, FX, VS4000 - page 88
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 78 www.polycom.com The Deployment Process The diagram below summarizes the tasks involved in the deployment process. This chapte r assumes that the appropriate products have been ordered, and that you have done the appropriate predeployment tasks. Figure 4-1. The Deploym ...
-
Polycom EX, FX, VS4000 - page 89
Chapter 4 - Installing Vi deoconferencing Systems © Polycom, Inc. 79 Installation Procedures For basic system installation, please refer to the installation instructions in the appropriate Us er Guide and the QuickStart cards. Installing Network Interface Modules The ViewStation EX, ViewStation FX, a nd VS4000 may be purchased with either of th es ...
-
Polycom EX, FX, VS4000 - page 90
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 80 www.polycom.com NT-1 Device The Quad BRI network int erface modu le requires an S/T interf ace. If your site does not use an inte rnal telephone system (PBX) , you must connect the Quad BRI module to th e ISDN line(s) through a network termination (NT-1) device, which ...
-
Polycom EX, FX, VS4000 - page 91
Chapter 4 - Installing Vi deoconferencing Systems © Polycom, Inc. 81 3. Connect the network side of the Quad BRI network interface module to the NT-1 device or to the ISDN network, as appropriate. Figure 4-4. Quad BRI Network Interface Module (Network Side) 4. I f y o u a r e u s i n g a n N T - 1 d e v i c e , c o n n e c t i t t o t h e I S D N ...
-
Polycom EX, FX, VS4000 - page 92
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 82 www.polycom.com You must use an external power supply if you use the internal CSU capability of the PRI T1 network interface module. Channel Service Unit In North America, the PRI T1 network interface module can be connected to an external Channel Service Unit (CSU). ...
-
Polycom EX, FX, VS4000 - page 93
Chapter 4 - Installing Vi deoconferencing Systems © Polycom, Inc. 83 If You Are Connecting to a PBX ❑ Some PBXs require a crossover cable. ❑ The PBX must provide the clock signal and act as the network side for layers 1, 2, and 3 . ❑ QSIG signaling (PSS1) is not supported. However, a PRI network interface module can be connected to a PISN th ...
-
Polycom EX, FX, VS4000 - page 94
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 84 www.polycom.com Installation To install the PRI network interface module: 1. Ensure that the system i s powered off. 2. Connect peripheral side of the PRI network interface module to the system using the supplied cable. Figure 4-5 shows the peripheral side of the PRI ...
-
Polycom EX, FX, VS4000 - page 95
Chapter 4 - Installing Vi deoconferencing Systems © Polycom, Inc. 85 Installing a V.35/RS- 449/RS-530 Network Interface Module Cables Used with the V.35/RS-449/RS-530 Network Interface Module The network interface module conne cts to the syst em using a cable that is not interchangeable with st andard RJ-45 to RJ-4 5 cables. The following optional ...
-
Polycom EX, FX, VS4000 - page 96
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 86 www.polycom.com Installation To install V.35/RS-44 9/RS-530 Network Interface Modu le: 1. Make sure the system is turned off. 2. Connect the peripheral side of the network interface module to the system. Refe r to Figure 4-7. Figure 4-7. V.35/RS-449/RS-530 Network In ...
-
Polycom EX, FX, VS4000 - page 97
Chapter 4 - Installing Vi deoconferencing Systems © Polycom, Inc. 87 Note If your DCE does not use dialing, do not use the RS-366 (DB-25M) connector. ...
-
Polycom EX, FX, VS4000 - page 98
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 88 www.polycom.com Network Configuration The following paragraphs give information about config uring the ViewStation EX, ViewStation FX, and VS 4000 systems for the ISDN network. On a PRI T1 Network: Configuring the CSU If you use an external CSU, you must specify the f ...
-
Polycom EX, FX, VS4000 - page 99
Chapter 4 - Installing Vi deoconferencing Systems © Polycom, Inc. 89 Firewall and NAT Issues A firewall protects an organizati on’s network by controlling data traffic from outside the network. Different types of firewalls use different techniques to provide network security, but unless the firewall is designed to work with H.323 videoconferenci ...
-
Polycom EX, FX, VS4000 - page 100
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 90 www.polycom.com Configuring the System to Operate Behind a NAT The System is behind a NAT option allows the user make calls outside the internal network. At this time, it is not possi ble to make videoconferencing call s within the internal network when the System is ...
-
Polycom EX, FX, VS4000 - page 101
Chapter 4 - Installing Vi deoconferencing Systems © Polycom, Inc. 91 Connecting the System to a PC In s o m e s i tu a t i on s y ou m a y w a n t to c o nn e c t a l a p to p d ir e c tl y t o t h e ViewStation EX, ViewStation FX, or VS4000. This allows you to: ❑ Update software on a system th at is not connected to a LAN. ❑ Use IP-based func ...
-
Polycom EX, FX, VS4000 - page 102
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 92 www.polycom.com Connecting the PC to the LAN Through the ViewStation EX, ViewStation FX, or VS4000 Do this if you need to use the system to provide LA N connectivity for your PC. 1. Ensure that the PC and the system are both powered off. 2. Connect the system to the L ...
-
Polycom EX, FX, VS4000 - page 103
Chapter 4 - Installing Vi deoconferencing Systems © Polycom, Inc. 93 10. Select Off in the DHCP field and manually en ter the IP address, subnet mask, and gateway addre ss provided by your system administrator. 11. Turn on your PC and make sure i t is properly configured . 12. After you have changed the DHCP sett ings, a message lets you know that ...
-
Polycom EX, FX, VS4000 - page 104
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 94 www.polycom.com Connecting the System to a PC off the LAN D o t h is i f y o u n e e d t o u s e I P - b a s ed f u n c t i o n s ( d i s p l a y d e sk to p , d o a software update, use PolySnap) on a system that is not connected to a LAN. Caution Your system must be ...
-
Polycom EX, FX, VS4000 - page 105
Chapter 4 - Installing Vi deoconferencing Systems © Polycom, Inc. 95 6. Select Yes if you are absolutely certain you want to set your system as a DHCP server. 7. Press Menu . The following message will appear: “Power must be reset to save changes. Continue?” Select Yes . 8. Your ViewStation will automatically restart. It will now act as a DHCP ...
-
Polycom EX, FX, VS4000 - page 106
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 96 www.polycom.com Placing Test Calls To verify that you have installe d the endpoint equipment correctly, test each unit as follows: ❑ Place an ISDN call from the unit. ❑ Place an IP call from the unit. ❑ From a suitable endpoint, place an ISDN call to the unit. ? ...
-
Polycom EX, FX, VS4000 - page 107
© Polycom, Inc. 97 5 Supporting Advanced Users This chapter describes features th at are available but not widely used. Inexperienced users may need assistance with these featur es. This chapter covers the follow ing topics. Topic Page Multiple-Monitor Mode 98 RS-232 Interface 105 ...
-
Polycom EX, FX, VS4000 - page 108
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 98 www.polycom.com Multiple-Monitor Mode The following table describes each monitor’s expected behavior in systems using one to four monitors. Table 5-1. Expected Di splay for Each Monitor Condition PIP Monitor System VGA or Visual Concert VGA 1234 Booting None Logo Lo ...
-
Polycom EX, FX, VS4000 - page 109
Chapter 5 - Supporting Advanced Users © Polycom, Inc. 99 Point-to-point call: call connect Near Far No change Point-to-point call: main/UI Far Main No change Point-to-point call: graphic Near Far Graphic Multipoint call: main/UI Last talker Main No change Three-way call: graphic Near Far Graphic Four-way call: graphic None Cont. presence No change ...
-
Polycom EX, FX, VS4000 - page 110
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 100 www.polycom.com Multipoint call: graphic None Cont. presence Graphic Three-way call: discussion mode Near Far Far (2) Three-way call: presentation mode Near Far Far (2) Three-way call: full-screen mode Near Far Far (2) Four-way call: discussion mode None Cont. presen ...
-
Polycom EX, FX, VS4000 - page 111
Chapter 5 - Supporting Advanced Users © Polycom, Inc. 101 Three-way call: full-screen mode Near Far Far (2) Four-way call: graphic None Cont. presence Last talker Graphic Four-way call: discussion mode None Cont. presence Last talker Four-way call: presentation mode None Cont. presence Last talker Four-way call: full-screen mode None Last talker N ...
-
Polycom EX, FX, VS4000 - page 112
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 102 www.polycom.com Four-way call: graphic None Cont. presence Graphic Last talker Four-way call: discussion mode Near Far Far (2) Far (3) Four-way call: presentation mode Near Far Far (2) Far (3) Four-way call: full-screen mode Near Far Far (2) Far (3) Three-monitor mod ...
-
Polycom EX, FX, VS4000 - page 113
Chapter 5 - Supporting Advanced Users © Polycom, Inc. 103 Four-way call: discussion mode Near Far Far (2) Far (3) Four-way call: presentation mode Near Far Far (2) Far (3) Four-way call: full-screen mode Near Far Far (2) Far (3) Four-monitor mode, no VGA Not in a call: main/UI No ne Main Near No ne None Not in a call: graphic None Ne ar Graphic No ...
-
Polycom EX, FX, VS4000 - page 114
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 104 www.polycom.com Four-way call: presentation mode None Far Near Far (2) Far (3) Four-way call: full-screen mode None Far Near Far (2) Far (3) Four-monitor mode, VGA Not in a call: main/UI No ne Main Near No ne None Not in a call: graphic None Near None None None Graph ...
-
Polycom EX, FX, VS4000 - page 115
Chapter 5 - Supporting Advanced Users © Polycom, Inc. 105 RS-232 Interface RS-232 Control Mode In Control Mode, the ViewStation E X, ViewStation FX, or VS4000 is under the control of the PC or othe r device connected to its RS-232 port. RS-232 Pass-Thru Mode Pass-Thru Mode allows two endpoint s to pass data from one unit’s RS-232 port t o the ot ...
-
Polycom EX, FX, VS4000 - page 116
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 106 www.polycom.com Both endpoints in Pass-Thru Mode —Two statio ns set to Pass-Thru Mode behave as a null-modem betw een their respective exter nally connected devices. Data from the RS-232 port on one endpoint is pushed through the call to the other endpoint, and the ...
-
Polycom EX, FX, VS4000 - page 117
Chapter 5 - Supporting Advanced Users © Polycom, Inc. 107 Configure the System for RS-232 Operation To configure your system to use the RS-232 interface: 1. Select System Info > Admin Setup > Software/Hardware > RS-232 to display the RS-232 screen 2. Configure the Baud Rate . 3. Configure the RS-232 Mode . Select Control Mode to allow the ...
-
Polycom EX, FX, VS4000 - page 118
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 108 www.polycom.com 4. In the Com1 Properties window, under Port Settin gs, select the following setti ngs: • Baud rate should match that of the system (defa ult is 9600) • Data bits = 8 • Parity = none • Stop bits = 1 • Flow control setting should match that o ...
-
Polycom EX, FX, VS4000 - page 119
© Polycom, Inc. 109 6 Testing and Troubleshooting This chapter describes how to do post-deployment functional tests and how to identify and correct problems. This chapter covers the follow ing topics. Indicator Lamps The ViewStation EX, ViewStation FX, and VS4000 and their network interface mod ules have indicator lamps (LEDs) that can help you to ...
-
Polycom EX, FX, VS4000 - page 120
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 110 www.polycom.com Indicator Lamps on the PR I Network Interface Module The PRI network interface module uses lamps on both the network side and the peripheral s ide to provide status indications. Note The PRI network interface module is not available with the ViewStati ...
-
Polycom EX, FX, VS4000 - page 121
Chapter 6 - Testing and Troubleshooting © Polycom, Inc. 111 Indicator Lamps on the Quad BRI Network Interface Module The Quad BRI network interface module uses pairs of indicator lamps associated w ith each BRI line to provide status indi cations. The table below shows the meanings of the LED pair associated with one line. Note that the lines in u ...
-
Polycom EX, FX, VS4000 - page 122
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 112 www.polycom.com Indicator Lamps on the V. 35/RS-449/RS-530 Network Interface Module The V.35/RS-4 49/RS-530 netwo rk interface module uses lamps on both the network side and the peri pheral side to provide status indications . Table 6-4. V.35/RS-449/RS-530 Indicator ...
-
Polycom EX, FX, VS4000 - page 123
Chapter 6 - Testing and Troubleshooting © Polycom, Inc. 113 Fault Isolation The following table lists symptoms , causes, and corrective actions for equipment malfunctions. Table 6 -6. Fault Isolation Problem Possible cause Corrective action Monitor screen remains blank Monito r is not connected to power Check all cables to equipment Monitor is not ...
-
Polycom EX, FX, VS4000 - page 124
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 114 www.polycom.com ISDN Error Codes The following table des cribes codes that the ISDN switch se nds to the router to indicate call status. Although the codes are standardized, each ISDN service pr ovider defines them differe ntly. Because of this, the d efinitions in t ...
-
Polycom EX, FX, VS4000 - page 125
Chapter 6 - Testing and Troubleshooting © Polycom, Inc. 115 21 Call rejected The destination equipm e nt is capable of accepting the call, but has rejected it for an unknown reason. 22 Number changed The ISDN number used to set up the call is no longer valid. (The diagnostic field of the message may return an a lternate address assigned to the cal ...
-
Polycom EX, FX, VS4000 - page 126
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 116 www.polycom.com 42 Switching equipment congestion The destination canno t be reached because the network switching equipmen t is temporarily overloaded. 43 Access information discarded The requested access information cannot be provided by the network. The diagnostic ...
-
Polycom EX, FX, VS4000 - page 127
Chapter 6 - Testing and Troubleshooting © Polycom, Inc. 117 69 Requeste d facility not implemented The remote equipment is not capable of providing the re quested supplementary service. 70 Only restricted digital information bearer is available The network is unable to provide unrestricted digi tal information over bearer capability. 79 Service or ...
-
Polycom EX, FX, VS4000 - page 128
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 118 www.polycom.com 91 Invalid transit network specified The ISDN exchange was asked to route the call thro ugh an unrecognized intermediate network. 95 Invalid message, unspecified An invalid message was received, for an unknown reason. This is usually due to a D-channe ...
-
Polycom EX, FX, VS4000 - page 129
Chapter 6 - Testing and Troubleshooting © Polycom, Inc. 119 102 Recovery on timer expiry A time-out has triggered an error-handling (recovery) procedure. This proble m is typically temporary. 111 Protocol error, unspecified An unspecified D-channel error when no other standard cause applies. 127 Interworking, unspecified An event occurred within a ...
-
Polycom EX, FX, VS4000 - page 130
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 120 www.polycom.com ...
-
Polycom EX, FX, VS4000 - page 131
© Polycom, Inc. 121 A System Interoperability The ViewStation EX, ViewStation FX, a nd VS4000 can work with the following non-Polycom endpoint equipment: Table A-1. H.320 En dpoints Manufacturer Model Version Sony PCS6000 4.1 Tandberg 500 800 1000 2000 6000 B5.1 VCON Cruiser Media Connect 8000 4.6 VTEL Galaxy 2.2.0.0 70 ...
-
Polycom EX, FX, VS4000 - page 132
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 122 www.polycom.com Table A-2. H.323 Endpoints Manufacturer Model Version Microsoft NetMeeting 2.1, 3.0, 3.01 a a. No application sharing, file transfer, or whiteboa rding in versions 3.0 and 3.01 Tandberg 500 800 1000 2500 6000 B5.1 VCON Cruiser Escort Media Connect 800 ...
-
Polycom EX, FX, VS4000 - page 133
Appendix A - System Interoperability © Polycom, Inc. 123 The ViewStation EX, ViewStation FX, and VS4000 can work with the following non-Pol ycom MCUs: The ViewStation EX, ViewStation FX, and VS4000 can work with the following non-Polycom gateways and gatekeepers: Table A-3. H.323 MCU Interoperability Manufacturer Model Version H.320 Lucent Multi-P ...
-
Polycom EX, FX, VS4000 - page 134
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 124 www.polycom.com The ViewStation EX, ViewStation FX, and VS4000 can work with the following NATs an d firewalls: Radvision L2W-323BRI Gateway/Gatekeeper L2W-323PRI Gateway/Gatekeeper 2.2.3.2.5 MCU Gatekeeper 2.2.1.0.9d NGK 200 Gatekeeper 1.0 T120 Data Colla borator Se ...
-
Polycom EX, FX, VS4000 - page 135
© Polycom, Inc. 125 B ViewStation Series Cables The following tables list cables for systems in the ViewStation family. Board Room and Custom Room Systems Table B-1. Cables for VS4000 Use Description Leng th and pinout Longer versi on PC Ethernet Bl ue RJ-45 25 ft (7.6 m), Standard No Camera, document camera, or monitor (6) Yellow S-video 25 ft (7 ...
-
Polycom EX, FX, VS4000 - page 136
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 126 www.polycom.com Table B-2. Cables for View Station EX and ViewStation FX Use Description Leng th and pinout Longer versi on PC Ethernet Bl ue RJ-45 25 ft (7.6 m), Standard No IP network Orange RJ-45 12 ft (3.7 m), Standard No Audio device input Single bla ck RCA 8 ft ...
-
Polycom EX, FX, VS4000 - page 137
Appendix B - ViewStation Series Cables © Polycom, Inc. 127 Table B-4. Cables for ViewStation EX, ViewStation FX, and VS4000 Accessories Use Description Length and pinout Longer version Visual Concert FX to PC VGA, audio, LAN composite cable 5 ft (1.5 m) Custom No Visual Conc ert FX to ViewStation EX, FX or VS4000 RJ-45 TO RJ-45/RJ-9/2-pin Molex 30 ...
-
Polycom EX, FX, VS4000 - page 138
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 128 www.polycom.com Medium and Large Room Systems Table B-6. Cables for ViewStation H.323 Use Description Leng th and pinout Longer versi on IPOTS Pink RJ-11 12 ft (3.7 m) No IP network Orange RJ-45 12 ft (3.7 m), Standard No PC Ethernet Bl ue RJ-45 25 ft (7.6 m), Standa ...
-
Polycom EX, FX, VS4000 - page 139
Appendix B - ViewStation Series Cables © Polycom, Inc. 129 Table B-7. Cables for ViewStation MP Use Description Length an d pinout Longer version IPOTS Pink RJ-11 12 ft (3.7 m ) No IP network Orange RJ-45 12 ft (3.7 m), Standard No PC Ethernet Blue RJ-45 25 ft (7.6 m), Standard No Audio device input Black single RCA 8 ft (2.4 m), Standard No VCR R ...
-
Polycom EX, FX, VS4000 - page 140
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 130 www.polycom.com Small Room Systems Network inte rface (4) DCP- clear RJ-45 20 ft (6.1 m), Standard No DCP interface only DCP Green/white RJ-45 20 ft (6.1 m), Standard, keyed No Table B-9. Cables for Upgrading ViewStation Mo dels (Except FX) Use Description Leng th an ...
-
Polycom EX, FX, VS4000 - page 141
Appendix B - ViewStation Series Cables © Polycom, Inc. 131 Table B-11. C ables for ViewStation 128 Use Description Leng th and pinout Longer versi on IPOTS Pink RJ-11 12 ft (3.7 m) No IP Network Orange RJ-45 12 ft (3.7 m), standard No PC Ethernet Bl ue RJ-45 25 ft (7.6 m), st andard No Audio device input Black single RCA 8 ft (2.4 m), standard No ...
-
Polycom EX, FX, VS4000 - page 142
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 132 www.polycom.com ...
-
Polycom EX, FX, VS4000 - page 143
© Polycom, Inc. 133 Safety and Legal Notices Important Safeguards Read and understand the following instructions before using any equipment described in t his manual: • Close supervision is necessary when the system is used by or near children. Do not leave unattended while in use. • Only use electrical extension co rds with a current rating a ...
-
Polycom EX, FX, VS4000 - page 144
Integrators’ Reference Manual for ViewStation EX, ViewStation FX, and VS4000 134 www.polycom.com Limitation of Remedies and Damages Polycom, Inc., its agen ts, employees, sup pliers, dealers a nd other authorize d representatives shall not be responsible or lia ble with respec t to the product or any other subjec t matter related thereto under an ...
-
Polycom EX, FX, VS4000 - page 145
© Polycom, Inc. 135 Index A acoustics 73 address E.164 56 H.323 (IP) 56 administration plan 58 Adtran Atlas 800 Plus E1 module 82 ARENA API 19 , 20 audio codecs 17 audio quality 17 , 73 B bandwidth allocation policy 58 PRI E1 26 PRI T1 26 requirements calculating 50 browser, see Web browser 19 C cable adapter coaxial, for ViewStation F X/VS4000 PR ...
-
Polycom EX, FX, VS4000 - page 146
ViewStation FX and VS4000 Integrators’ Reference Manual 136 www.polycom.com cascading 18 channel restarts, Adtran Atlas 800 Plus E1 module 82 channel selection, ViewStation FX/VS4000 PRI 30 channel service unit, see CSU 82 clock source PRI 26 , 83 V.35/RS-449 32 closed captioning 19 codecs video 14 codecs, audio 17 collaboration tools 19 common s ...
-
Polycom EX, FX, VS4000 - page 147
Chapter - © Polycom, Inc. 137 GUI, ViewStation FX/VS4000 19 I indicator lamps, see specific equipment models 22 internal telephone system, see PBX 22 interoperability 121 , 122 , 123 , 124 IP address 92 DCHP 92 , 93 , 94 , 95 NAT 89 , 90 IP precedence 50 ISDN connection 25 ISDN error codes 114 , 115 , 116 , 117 , 118 , 119 ISDN network interface m ...
-
Polycom EX, FX, VS4000 - page 148
ViewStation FX and VS4000 Integrators’ Reference Manual 138 www.polycom.com power supply, for ViewStation FX/VS4000 PRI 81 , 82 power supply, PRI 84 PowerPoint file conversion tool 19 presentation mode ViewStation FX/VS4000 four monitors 103 , 104 , 105 single monitor 98 , 99 three monitors 101 , 102 two monitors 100 presentation tools 19 preset ...
-
Polycom EX, FX, VS4000 - page 149
Chapter - © Polycom, Inc. 139 video signal format 14 ViewStation FX cable, RS-232 20 defined 12 ViewStation FX/VS4000 audio specifications 16 , 17 cable extension to network interface module 83 Quad BRI to network 24 to network interface module 23 , 83 , 84 configuration 92 connecting to PC Ethernet port 91 DHCP server 94 electrical specif ication ...
-
Polycom EX, FX, VS4000 - page 150
ViewStation FX and VS4000 Integrators’ Reference Manual 140 www.polycom.com Z zone plan 57 ...
Do you have a question concerning Polycom EX, FX, VS4000?
Use the form below
If you did not solve your problem by using a manual Polycom EX, FX, VS4000, ask a question using the form below. If a user had a similar problem with Polycom EX, FX, VS4000 it is likely that he will want to share the way to solve it.