English dropdown-ico

Manual Agilent Technologies N9010A

262 pages 3.7 mb
Download

Go to site of 262

Summary
  • Agilent Technologies N9010A - page 1

    Agilent X-Series Signal Analyzer N9010A EXA Specifications Guide (Compr ehensive Reference Data) This manual provides documentation for the following X-Series Analyzer: EXA Signal Analyzer N9010A ...

  • Agilent Technologies N9010A - page 2

    Notices © Agilent T echnologies, Inc. 2007 - 20 10 No part of this manual may be reproduced in any form or by any means ( including electronic storage and retrieval or transla- tion into a foreign language) without prior agreement and written consent fro m Agi- lent T echnologies, Inc. as governed by United St at es and inte rna tional copyright l ...

  • Agilent Technologies N9010A - page 3

    3 Notice Wa r r a n t y This Agilent technologies instrument product is warranted against defect s in material and workmanship for a period of one year from the date of shipment. Duri ng the warranty period, Agile nt T echnologies will, at its option, either repair or replace products that prove to be defective. For warranty service or repair , thi ...

  • Agilent Technologies N9010A - page 4

    4 ...

  • Agilent Technologies N9010A - page 5

    Contents 5 1. Agilent EXA Sig nal Analyzer Definitions and Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Agilent Technologies N9010A - page 6

    6 Contents Power Suite Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Channel Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Occupied Bandwidth. . . . . . . . ...

  • Agilent Technologies N9010A - page 7

    Contents 7 5. Option PFR - Precision Frequency Reference Specifications Affected by Preci sion Frequency Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 0 6. I/Q Analyzer Specifications Affected by I/Q An alyzer: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Agilent Technologies N9010A - page 8

    8 Contents (EVM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 Power vs. T ime . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 EDGE Power vs. T ime . ...

  • Agilent Technologies N9010A - page 9

    Contents 9 AM Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 Residual PM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 Measurement Range . . . . . ...

  • Agilent Technologies N9010A - page 10

    10 Contents Occupied Bandwidth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182 Spectrum Emission Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 Spurious Emissions . . . . . . . . . . . ...

  • Agilent Technologies N9010A - page 11

    Contents 11 20. DVB-T/H Measur ement Application N6153A, DVB-T/H Measuremen ts Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218 Channel Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 218 Channel Power ...

  • Agilent Technologies N9010A - page 12

    12 Contents Frequency Points per Span . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248 Resolution Bandwidth (RBW) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 248 Input . . . . . . . . . . . . . . . . . . . . . ...

  • Agilent Technologies N9010A - page 13

    13 1 Agilent EXA Signal Analyzer This chapter contains the specifications for th e core signal analyzer . The specifications and characteristics for the me asurement applications and options are covered in the ch ap ters that follow . ...

  • Agilent Technologies N9010A - page 14

    14 Chapter 1 Agilent EXA Si gnal Analyzer Definitions an d Req uirements Definitions and Requir ements This book cont ains signal analyzer sp ecifications and supplemental informatio n. The distinctio n amon g specifications, typical performance, and no minal values are described as follows . Definitions • Specifications describe the performance ...

  • Agilent Technologies N9010A - page 15

    Chapter 1 15 Agilent EXA Si gnal Analyzer Frequency and T ime Fr equency and T ime Description Specifications Supplemental I nformation Frequency Range Maximum Frequency Option 503 3.6 GHz Option 507 7 GHz Option 513 13.6 GH z Option 526 26.5 GH z Pr eamp Option P03 3.6 GHz Minimum Frequency Preamp AC Coupled DC Coupled Off 10 MHz 9 kHz On 10 MHz 1 ...

  • Agilent Technologies N9010A - page 16

    16 Chapter 1 Agilent EXA Si gnal Analyzer Freq uen cy and Ti me a. In the band o verlap regions, for example , 3.5 to 3.6 GHz, the analyzer may use either band for measurements, in this example Band 0 or Band 1. The analyzer gives pr eference to the band with the better overall specifications (which is the lower numbered ba nd for all frequencies b ...

  • Agilent Technologies N9010A - page 17

    Chapter 1 17 Agilent EXA Si gnal Analyzer Frequency and T ime Achievable Initial Calibration Accuracy ± 1.4 × 10 − 6 Settabili ty ± 2 × 10 − 8 Residual FM Center Frequency = 1 GHz 10 Hz RBW , 10 Hz VBW ≤ 10 Hz × N p-p in 20 ms c , nominal a. Calibration accuracy d epe nds on how accura te ly the frequency standard was adjusted to 10 MHz. ...

  • Agilent Technologies N9010A - page 18

    18 Chapter 1 Agilent EXA Si gnal Analyzer Freq uen cy and Ti me Description Specifications Supplemental Informat ion Prec ision Fr equency Refer ence ( Option PFR ) Accuracy ± [(time since last adjustment × aging rate) + temperature stability + calibration accuracy a ] b a. Calibration accuracy d epe nds on how accura te ly the frequency standard ...

  • Agilent Technologies N9010A - page 19

    Chapter 1 19 Agilent EXA Si gnal Analyzer Frequency and T ime d. The achievable ca libration accuracy at the be ginning of the calibra tion cycle includes these effects: 1) T emperature difference between the calib ration environment and the use environment 2) Orientation relative to the gravitation fiel d changing between the calibration environme ...

  • Agilent Technologies N9010A - page 20

    20 Chapter 1 Agilent EXA Si gnal Analyzer Freq uen cy and Ti me Description Specifications Supplemental Information Freq uen cy Read out Accuracy ± (marker freq. × freq. ref. accy . + 0.25 % × span + 5 % × RBW a + 2 Hz + 0.5 × horizontal resolut ion b ) a. The warranted performance is only the sum of all errors under autocoupled con ditions. U ...

  • Agilent Technologies N9010A - page 21

    Chapter 1 21 Agilent EXA Si gnal Analyzer Frequency and T ime d. In most cases, the frequency read out accuracy of the ana lyzer can be exceptionally good. As an example, Agilent has characterized the accuracy of a span co mmonly used for Electro-Mag- netic Compatibility (EMC) testing using a source fre quency locked to the analyzer . Ideally , thi ...

  • Agilent Technologies N9010A - page 22

    22 Chapter 1 Agilent EXA Si gnal Analyzer Freq uen cy and Ti me Description Specifications Supplemental Information Frequency Counter a a. Instrument conditions: RBW = 1 kHz, gate time = auto (100 ms), S /N ≥ 50 dB, frequency = 1 GHz See note b b. If the signal being measured is locked to the same frequency reference as the analyz er , the specif ...

  • Agilent Technologies N9010A - page 23

    Chapter 1 23 Agilent EXA Si gnal Analyzer Frequency and T ime Description Specifications Supplemental Informatio n Sweep Time Range Span = 0 Hz Span ≥ 10 Hz 1 μ s to 6000 s 1 ms to 4000 s Accuracy Span ≥ 10 Hz, swept Span ≥ 10 Hz, FFT Span = 0 Hz ± 0.01 % (nominal) ± 40 % (nominal) ± 0.01 % (nominal) Sweep Trigger Free Run, Line, V ideo, ...

  • Agilent Technologies N9010A - page 24

    24 Chapter 1 Agilent EXA Si gnal Analyzer Freq uen cy and Ti me Sweep T ype = FFT T riggers on the signal envelope in a bandwidth wider than the FFT width RF Burst Level Range − 50 to − 10 dBm plus att enuati on (nominal) Bandwidth ( − 10 dB) Most cases 16 MHz (nominal) Sweep T ype = FFT ; FFT W idt h = 25 MHz; Span ≥ 8 MHz 30 MHz (nom inal ...

  • Agilent Technologies N9010A - page 25

    Chapter 1 25 Agilent EXA Si gnal Analyzer Frequency and T ime Description Specifications Supplemental Informat ion Gated Sweep Gate Methods Gated LO Gated V id eo Gated FFT Span Range Any span Gate Delay Range 0 to 100.0 s Gate Delay Settability 4 digits, ≥ 100 ns Gate Dela y Jitter 33.3 ns p-p (nom inal) Gate Length Range Except Method = FFT 100 ...

  • Agilent Technologies N9010A - page 26

    26 Chapter 1 Agilent EXA Si gnal Analyzer Freq uen cy and Ti me Nominal Measur ement T ime vs. Span [Plot] Description Specifications Supplemental I nformation Number of Frequency Display T race Points (buckets) Factory preset 1001 Range 1 to 40,001 Zero and non-zero spans ...

  • Agilent Technologies N9010A - page 27

    Chapter 1 27 Agilent EXA Si gnal Analyzer Frequency and T ime Description Specifications Supplemental Information Resolution Band width (RBW) Range ( − 3.01 dB bandwidth ) 1 Hz to 8 MHz Bandwidths above 3 MHz are 4, 5, 6, and 8 MHz. Bandwidths 1 Hz to 3 MHz are spaced at 10 % spacing using the E24 series (24 per decade): 1.0, 1. 1, 1.2, 1.3, 1.5, ...

  • Agilent Technologies N9010A - page 28

    28 Chapter 1 Agilent EXA Si gnal Analyzer Freq uen cy and Ti me b. Resolution Bandwidth Accu racy can be observe d at slower sweep times than auto-coupled conditions. Normal sweep rates ca use the shape of the RBW filter displayed on the analyzer screen to widen by nominally 6 % . This widen ing declines to 0.6 % nominal when the Swp T ime Rules ke ...

  • Agilent Technologies N9010A - page 29

    Chapter 1 29 Agilent EXA Si gnal Analyzer Amplitude Accuracy and Range Amplitude Accuracy and Range Description Specifications Supplemental Information Measurement Range Displayed A verage Noise Level to +23 dBm Preamp On Displayed A verage Noise Level to +23 dBm Option P03 Input Attenuation Range 0 to 60 dB, in 10 dB steps Standard Input Attenuati ...

  • Agilent Technologies N9010A - page 30

    30 Chapter 1 Agilent EXA Si gnal Analyzer Amplitude Accuracy and Range Description Specifications Supplemental Information Marker Readout a a. Reference level and off-screen performance: Th e reference level (RL) behavior dif fers from some earlier analyzers in a way that makes this an alyzer more flexible. In other analyzers, the RL controlled how ...

  • Agilent Technologies N9010A - page 31

    Chapter 1 31 Agilent EXA Si gnal Analyzer Amplitude Accuracy and Range Frequency Response Description Specifications Supplemental Information Frequency Re sponse Refer to the footnote for Band Overlaps on page 15 . Maximum error relative t o reference condition (50 MHz) Mechanical attenuator only a Swept operation b a. See the Electronic Attenuator ...

  • Agilent Technologies N9010A - page 32

    32 Chapter 1 Agilent EXA Si gnal Analyzer Amplitude Accuracy and Range Description Specifications Supplemental Information IF Freq uency Response a a. The IF frequency response includes ef fects due to RF circuits such as input filters, that are a function of RF frequency , in add ition to the IF pass-band ef fects. Demodulation and FFT response re ...

  • Agilent Technologies N9010A - page 33

    Chapter 1 33 Agilent EXA Si gnal Analyzer Amplitude Accuracy and Range Description Specifications Supplemental Information Input Attenuation Switching Uncertainty Refer to the footnote for Band Overlaps on page 15 . Relative to 10 dB (reference setting) Frequency Range 50 MHz (reference frequency) ± 0.20 dB ± 0.08 dB (typical) Attenuation > 2 ...

  • Agilent Technologies N9010A - page 34

    34 Chapter 1 Agilent EXA Si gnal Analyzer Amplitude Accuracy and Range Description Specificati ons Supplemental Informat ion Absolute Ampl itude Accuracy At 50 MHz a 20 to 30 ° C 5 to 50 ° C a. Absolute amplitude accuracy is the total of al l amplitude measurement e rrors, and applies over the following subset of sett ings and con ditions: 1 Hz ? ...

  • Agilent Technologies N9010A - page 35

    Chapter 1 35 Agilent EXA Si gnal Analyzer Amplitude Accuracy and Range b. Absolute Amplitude Accuracy fo r a wide range of signal and measurement settings, covers the 95th percentile proportion with 95 % confiden ce. Here are the deta ils of what is covered and how the computation is made: The wide range of conditions of RBW , signal level, VBW , r ...

  • Agilent Technologies N9010A - page 36

    36 Chapter 1 Agilent EXA Si gnal Analyzer Amplitude Accuracy and Range Description Specifications Supplemental Informat ion RF Input VS WR at tuned frequency , DC Coupled Nominal a a. The nominal SWR stated is the worst case RF frequency in three repr esentative instruments. 10 dB attenuation, 50 MHz 1.07:1 Input Attenuation Frequency 0 dB ≥ 10 d ...

  • Agilent Technologies N9010A - page 37

    Chapter 1 37 Agilent EXA Si gnal Analyzer Amplitude Accuracy and Range Nominal VSW R [Plot] ...

  • Agilent Technologies N9010A - page 38

    38 Chapter 1 Agilent EXA Si gnal Analyzer Amplitude Accuracy and Range Description Specifications Supplemental Information Resolution Bandwidth Switching Uncertainty relative to reference BW of 30 kHz 1.0 Hz to 3 MHz RBW ± 0.10 dB Manually selected wide RBWs: 4, 5, 6, 8 MHz ± 1.0 dB Description Specifications Supplemental Information Reference Le ...

  • Agilent Technologies N9010A - page 39

    Chapter 1 39 Agilent EXA Si gnal Analyzer Amplitude Accuracy and Range Description Specifications Supplemental I nformation Display Scale Switching Uncertainty Switching between Linear and Log 0 dB a a. Because Log/Lin and Log Scale Switching affect only the display , not the measurement, they cause no additional error in measurem ent results from ...

  • Agilent Technologies N9010A - page 40

    40 Chapter 1 Agilent EXA Si gnal Analyzer Amplitude Accuracy and Range a. Supplemental information: The amplitude detection linearity speci fication applies at all levels below − 10 dBm at the input mixer; however , nois e will reduce the accur acy of low level mea- surements. The amplitude error due to noise is determined by th e signal-to-noise ...

  • Agilent Technologies N9010A - page 41

    Chapter 1 41 Agilent EXA Si gnal Analyzer Amplitude Accuracy and Range g. Slope error will nominally be well within the range of ± 0.0009 × (P1 − P2). P1 and P2 are defined in footnote f . h. A small additional error is possible. In FFT swee ps, this error is possible for spans under 4.01 kHz. For non-FFT measurements, it is possible for RBWs o ...

  • Agilent Technologies N9010A - page 42

    42 Chapter 1 Agilent EXA Si gnal Analyzer Dynamic Range Dynamic Range Gain Compression Description Specifications Supplemental Informatio n 1 dB Gain Compression Point (T wo-tone) abc a. Lar ge signa ls, even at frequencies not shown on the screen, can cause the analyzer to incor- rectly measure on-screen signals because of two- tone gain compressi ...

  • Agilent Technologies N9010A - page 43

    Chapter 1 43 Agilent EXA Si gnal Analyzer Dynamic Range c. Reference level and off-screen performance: Th e reference level (RL) behavior dif fers from some earlier analyzers in a way that makes this an alyzer more flexible. In other analyzers, the RL controlled how the measurement was perform ed as well as how it was displaye d. Because the logari ...

  • Agilent Technologies N9010A - page 44

    44 Chapter 1 Agilent EXA Si gnal Analyzer Dynamic Range Displayed A verage Noise Level Description Specifications Supplemental Informat ion Displayed A verage Noise Level (DANL) a a. DANL for zero span and sw ept is normalized in two ways and for two reasons. DANL is mea- sured in a 1 kHz RBW and normalized to the na rrowest available RBW , because ...

  • Agilent Technologies N9010A - page 45

    Chapter 1 45 Agilent EXA Si gnal Analyzer Dynamic Range c. Setting the IF Gain to Low is often desirable in order to allow higher power into the mixer without overload, better compression and better third-order intermodulation. When the Swept IF Gain is set to Low , either by auto co upling or manual coup ling, there is noise added above that speci ...

  • Agilent Technologies N9010A - page 46

    46 Chapter 1 Agilent EXA Si gnal Analyzer Dynamic Range Spurious Responses Description Specifications Supplemental Information Spurious Responses Mixer Level a Response Preamp Off b Refer to the footnote for Band Overlaps on page 15 . Residual Responses c 200 kHz to 8.4 GHz (swept) Zero span or FFT or other frequencies N/A − 100 dBm − 100 dBm ( ...

  • Agilent Technologies N9010A - page 47

    Chapter 1 47 Agilent EXA Si gnal Analyzer Dynamic Range a. Mixer Level = Input Level − Input Attenuation. b. The spurious response specifications onl y apply with the preamp turned of f. When the pre amp is turned on, performance is nomi nally the same as long as the mixe r level is interpreted to be: Mixer Level = Input Level − Input Attenuati ...

  • Agilent Technologies N9010A - page 48

    48 Chapter 1 Agilent EXA Si gnal Analyzer Dynamic Range Second Harmonic Distortion Third Order Intermodulation Distor tion Description Specifications Supplemental Informa tion Second Harmonic Distortion Mixer Leve l a a. Mixer level = Input Level − Input Attenuation SHI b (nominal) b. SHI = second harmonic intercep t. The SHI is given by the mixe ...

  • Agilent Technologies N9010A - page 49

    Chapter 1 49 Agilent EXA Si gnal Analyzer Dynamic Range 400 MHz to 1.7 GHz +10 dBm − 80 dBc 1.7 to 3.6 GHz +12 dBm − 84 dBc 3.6 to 5.1 GHz +10 dBm − 80 dBc 5.1 to 7 GHz +12 dBm − 86 dBc 7 to 13.6 GHz +10 dBm − 80 dBc 13.6 to 26.5 GHz +7 dBm − 74 dBc a. See the IF Prefilter Bandwidth table in the Gain Compression specifications on page 4 ...

  • Agilent Technologies N9010A - page 50

    50 Chapter 1 Agilent EXA Si gnal Analyzer Dynamic Range Nominal Dynamic Range at 1 GHz [Plot] ...

  • Agilent Technologies N9010A - page 51

    Chapter 1 51 Agilent EXA Si gnal Analyzer Dynamic Range Nominal Dynamic Rang e Bands 1-4 [Plot] ...

  • Agilent Technologies N9010A - page 52

    52 Chapter 1 Agilent EXA Si gnal Analyzer Dynamic Range Nominal Dynamic Range vs. Offs et Frequency vs. RBW [Plot] ...

  • Agilent Technologies N9010A - page 53

    Chapter 1 53 Agilent EXA Si gnal Analyzer Dynamic Range Phase Noise Description Specifications Supplemental Information Phase Noise Noise Si debands Center Frequency = 1 GHz a Best-case Optimization b Internal Reference c a. The nominal performance of the phase noise at frequencies above the fre quency at which the specifications apply (1 GHz) depe ...

  • Agilent Technologies N9010A - page 54

    54 Chapter 1 Agilent EXA Si gnal Analyzer Dynamic Range Nominal Phase Noise of Di fferent LO Opti mizations ...

  • Agilent Technologies N9010A - page 55

    Chapter 1 55 Agilent EXA Si gnal Analyzer Dynamic Range Nominal Phase Noise at Di fferent Center Fr equencies ...

  • Agilent Technologies N9010A - page 56

    56 Chapter 1 Agilent EXA Si gnal Analyzer Power Suite Measurements Power Suite Measurements Description Specifications Supplemental Information Channel Power Amplitude Accuracy Absolute Amplitude Accuracy a + Power Bandwidth Accuracy bc a. See “Absolute Amplitude A ccuracy” on page 34 . b. See “Frequency and T ime” on page 1 5 . c. Expresse ...

  • Agilent Technologies N9010A - page 57

    Chapter 1 57 Agilent EXA Si gnal Analyzer Power Suite Measurements Description Specifications Supplemental Information Adjacent Channel Power (ACP) Case: Radio S td = None Accuracy of ACP Ratio (dBc) Display Scale Fideli ty a Accuracy of ACP Absolute Power (dBm or dBm/Hz) Absolute Amplitude Accuracy b + Power Bandwidth Accuracy cd Accuracy of Carri ...

  • Agilent Technologies N9010A - page 58

    58 Chapter 1 Agilent EXA Si gnal Analyzer Power Suite Measurements On 5 M Hz Fil tered IBW − 73 dB − 8 dBm On 10 MHz Filtered IBW − 76 dB − 2 dBm RRC W eighting Accuracy n White noise in Adjacent Channel TOI-induced spectrum rms CW er ror 0.00 dB nominal 0.001 dB nominal 0.012 dB nominal a. The ef fect of scale fidelity on the ratio of tw o ...

  • Agilent Technologies N9010A - page 59

    Chapter 1 59 Agilent EXA Si gnal Analyzer Power Suite Measurements i. T o meet this specified accurac y when measuring mobile s tation (MS) or user equipm ent (UE) within 3 dB of the required − 33 dBc ACPR, the mixer level (ML) must be optimized for accu- racy . This optimum mixer level is − 22 dBm, so the input att enua tion must be set as clo ...

  • Agilent Technologies N9010A - page 60

    60 Chapter 1 Agilent EXA Si gnal Analyzer Power Suite Measurements n. 3GPP requires the use of a root-raised-cosine filter in evalua ting the ACLR of a device. The accuracy of the passband shape of the filter is not specified in standards, nor is any method of evaluating that accuracy . This f ootnote discusses the performance of the filter in this ...

  • Agilent Technologies N9010A - page 61

    Chapter 1 61 Agilent EXA Si gnal Analyzer Power Suite Measurements Description Specifications Supplemental Information Case: Radio S t d = IS-95 or J-STD-008 Method RBW method a a. The RBW method measures the power in the adjacent channels within the defined resolution bandwidth. The noise bandwidth of the RBW f ilter is nominally 1.055 times the 3 ...

  • Agilent Technologies N9010A - page 62

    62 Chapter 1 Agilent EXA Si gnal Analyzer Power Suite Measurements c. As in footnote b , the specified ACPR accuracy applies if the ACPR measured substantially exceeds the analyzer dynamic range at the specified offset. Wh en this condition is not met, there are additional errors due to the addition of analyzer sp ectral components to UUT spec- tra ...

  • Agilent Technologies N9010A - page 63

    Chapter 1 63 Agilent EXA Si gnal Analyzer Power Suite Measurements Description Specifications Supplemental Information Power S tatistics CCDF Histogram Resolution a a. The Complementary Cumulative Distribution Function (CCDF) is a reformatting of a histo- gram of the power envelope. The width of the amplitude bins used by the histogram is the his- ...

  • Agilent Technologies N9010A - page 64

    64 Chapter 1 Agilent EXA Si gnal Analyzer Power Suite Measurements Description Specifications Supplemental Information Spurious Emissions T able-driven spurious signals; search across regions Case: Radio S td = 3GPP W-CDMA Dynamic Range 1 to 3.6 GHz a a. The dynamic is specified with the mixer level at +3 dBm, where up to 1 dB of compression can oc ...

  • Agilent Technologies N9010A - page 65

    Chapter 1 65 Agilent EXA Si gnal Analyzer Power Suite Measurements Case: Radio S t d = 3G PP W − CDMA Dynamic Range, rel a tiv e 2.515 MHz offset a d 76.5 dB 83.9 dB (typical) Sensitivity , absolute 2.515 MHz offset c − 94.7 dBm − 100.7 dBm (typical) Accuracy 2.515 MHz offset Relative d ± 0.12 dB Absolute e 20 to 30 °C ± 1.05 dB ± 0.34 dB ...

  • Agilent Technologies N9010A - page 66

    66 Chapter 1 Agilent EXA Si gnal Analyzer Options Options The following options and applications af fect instrument specifications. Option 503: Frequency range, 9 kHz to 3.6 GHz Option 507: Frequency range, 9 kHz to 7 GHz Option 513: Frequency range, 9 kHz to 13.6 GHz Option 526: Frequency range, 9 kHz to 26.5 GHz Option B25: Analysis bandwidth , 2 ...

  • Agilent Technologies N9010A - page 67

    Chapter 1 67 Agilent EXA Si gnal Analyzer General General Description Specifications Supplemental Informat ion Calibration Cycle 1 year Description Specifications Supplemental Information T emperature Range Operating 5 to 50 ° CS t a n d a r d S torage − 40 to 65 ° C Altitude 3,000 meters (approx. 10,000 feet) Description Specifications Supplem ...

  • Agilent Technologies N9010A - page 68

    68 Chapter 1 Agilent EXA Si gnal Analyzer General Acoustic Noise Emission/Geraeuschemis sion LpA <70 dB Operator position Normal position Per ISO 7779 LpA <70 dB Am Arbeitsplatz Normaler Betrieb Nach DIN 45635 t.19 Description Specifications Safety Complies w ith European Low V oltage Directive 2006/95/ EC — IEC/EN 6101 0-1 2nd Edition — ...

  • Agilent Technologies N9010A - page 69

    Chapter 1 69 Agilent EXA Si gnal Analyzer General Description Supplemental Information Measurement Speed a a. Sweep Points = 101. Nominal Standard w/ Option PC2 Local measurement and display update rate bc b. Factory preset, fixed center frequency , RBW = 1 MHz, span >10 MHz and ≤ 600 MHz, stop frequency ≤ 3.6 GHz, Auto Align Of f. c. Phase ...

  • Agilent Technologies N9010A - page 70

    70 Chapter 1 Agilent EXA Si gnal Analyzer General a. The LCD display i s manufactured using high precision technolog y . However , there may be up to six bright points (white, blue, red or gree n in color) that constan tly appear on the LCD screen. These points are normal in the manufa cturing process and do not affect the measure- ment integrity o ...

  • Agilent Technologies N9010A - page 71

    Chapter 1 71 Agilent EXA Si gnal Analyzer Inputs/O utputs Inputs/Outputs Front Panel Description Specifications Supplemental Information RF Input Connector S tandard T ype-N female Impedance 50 Ω (nominal) Description Specifications Supplemental Information Probe Power V olta ge/Current +15 Vdc, ± 7 % at 150 mA max (nominal) − 12.6 Vdc, ± 10 % ...

  • Agilent Technologies N9010A - page 72

    72 Chapter 1 Agilent EXA Si gnal Analyzer Inputs/Outputs Rear Panel Description Specifications Supplemental I nformation Headphone Jack Connector 3.5 mm (1/8 inch) miniature stereo audio jack Output Power 90 mW per chann el int o 16 Ω (nominal) Description Specifications Supplemental Information 10 MHz Out Connector BNC female Impedance 50 Ω (nom ...

  • Agilent Technologies N9010A - page 73

    Chapter 1 73 Agilent EXA Si gnal Analyzer Inputs/O utputs Description Specifications Supplemental Information Sync Reserved for future use Connector BNC female Description Specifications Supplemental Information T rigger Inputs Either trigger source may be selected. T rigger 1 In, T rigger 2 In Connector BNC female Impedance 10 k Ω (nominal) T rig ...

  • Agilent Technologies N9010A - page 74

    74 Chapter 1 Agilent EXA Si gnal Analyzer Inputs/Outputs Description Specifications Supplemental I nformation Noise Source Drive +28 V (Pulsed) Connector BNC female Description Specifications Supplemental Informat ion SNS Series Noise Source For use with Agilent T echnologies SNS Series noise sources Description Specifications Supplemental Informat ...

  • Agilent Technologies N9010A - page 75

    Chapter 1 75 Agilent EXA Si gnal Analyzer Inputs/O utputs Description Specifications Supplemental Informat ion USB 2.0 Ports Master (4 ports) Connector USB T ype “A” (female) Output Curren t 0.5 A (nominal) Slave (1 port) Connector USB T ype “B” (female) Output Curren t 0.5 A (nominal) Description Specifications Supplemental Information GPI ...

  • Agilent Technologies N9010A - page 76

    76 Chapter 1 Agilent EXA Si gnal Analyzer Regulatory Information Regulatory Information This product is designed for use in Installation Category II and Pol lution Degree 2 per IEC 61010 2n d ed, and 664 respectively . This product has been designed and tested in ac cord ance with accepted industry standards, and has been supplied in a safe conditi ...

  • Agilent Technologies N9010A - page 77

    Chapter 1 77 Agilent EXA Si gnal Analyzer Declaration of Conformity Declaration of Conformity A copy of the Manufacturer ’ s European De claration of Conformity for this instrument can be obtained by contacting your local Agilent T echnologies sales representative. ...

  • Agilent Technologies N9010A - page 78

    78 Chapter 1 Agilent EXA Si gnal Analyzer Declaration of Co nf ormity ...

  • Agilent Technologies N9010A - page 79

    79 2 Option B25 (25 MHz) - Analysis Bandwidth This chapter contains specifications for the Op tion B25 (25 MHz) Analysis Bandwidth, an d fo r convenience, also has specifications for the standard bandwidt hs of 10 MHz and below . ...

  • Agilent Technologies N9010A - page 80

    80 Chapter 2 Option B25 (25 MHz) - Analysis Bandwidth Specifications Affected by Analysis Bandwidth Specifications Affected by Analysis Bandwidth Specification Name Information IF Frequency Response Specifications presented in the core chapter ( “Agilent EXA Signal Analyzer” on page 13 ) are redundantly contained within this chapter . IF Phase ...

  • Agilent Technologies N9010A - page 81

    Chapter 2 81 Option B25 (25 MHz) - Analysis Bandwidth Other Analysis Band width Specifications Other Analysis Bandwidth Specifications Description Specification Supplemental Information IF Spurious Response, 25 MHz IF Bandwidth (Op ti on B25) a a. T o save test time, the levels of these sp urs are not warranted. However , the relationship between t ...

  • Agilent Technologies N9010A - page 82

    82 Chapter 2 Option B25 (25 MHz) - Analysis Bandwidth Other Analysis Band width Specificatio ns Description Specifications Supplemental Informat ion SFDR (Spurious-Fr ee Dynamic Range) T est conditions a a. Signal level is –6 dB relative to dBfs wh ere: FS = –1 0 dBm at mixer , IF Gain = 0.. Signal Frequency wi thin ± 12 MHz of center –75 dB ...

  • Agilent Technologies N9010A - page 83

    Chapter 2 83 Option B25 (25 MHz) - Analysis Bandwidth Other Analysis Band width Specifications Description Specification Supplemental I nformation IF Phase Linearity Relative to mean phase linearity Freq (GHz) Span (MHz) Peak (nominal) rms (nom inal) a a. The listed performance is the r .m.s. of the phase deviation relative to the a best-fit linear ...

  • Agilent Technologies N9010A - page 84

    84 Chapter 2 Option B25 (25 MHz) - Analysis Bandwidth Other Analysis Band width Specificatio ns ...

  • Agilent Technologies N9010A - page 85

    85 3 Option EA3 - Electr onic Attenuator , 3.6 GHz This chapter contains specifications for the Option EA3 Electronic Attenuator , 3.6 GHz. ...

  • Agilent Technologies N9010A - page 86

    86 Chapter 3 Option EA3 - Electronic Attenuator , 3.6 GHz Specifications Affected by Electronic Attenuator Specifications Affected by Electronic Attenuator Specification Name Information Frequency Range See “Range (Frequency and Attenuation)” on page 87 . 1 dB Gain Compression Point See “Distortions and Noise” on page 88 . Displayed A verag ...

  • Agilent Technologies N9010A - page 87

    Chapter 3 87 Option EA3 - Electr onic Attenu at or , 3.6 GHz Other Electronic Attenu ator Specificat ions Other Electr onic Attenuator Specifications Description Specifications Supplemental I nformation Range (Frequency and Attenuation) Frequency Range 9 kHz to 3.6 GHz Attenuation Range Electronic Attenuator Range 0 to 24 dB, 1 dB steps Calibrated ...

  • Agilent Technologies N9010A - page 88

    88 Chapter 3 Option EA3 - Electronic Attenuator , 3.6 GHz Other Electronic Attenuator Specifications Description Specifications Supplemental Information Distortions and Noise When using the electronic attenuator, the mechanical attenuator is also in-circuit. The full mechanical attenuator range is available a . a. The electronic attenuator is calib ...

  • Agilent Technologies N9010A - page 89

    Chapter 3 89 Option EA3 - Electr onic Attenu at or , 3.6 GHz Other Electronic Attenu ator Specificat ions Description Specifications Supplemental Information Frequency Re sponse Maximum error relative t o reference condition (50 MHz) 20 to 30 ° C 5 to 50 ° C 95 th Percentile ( ≈ 2 σ ) Attenuation = 4 to 24 dB, even steps 9 kHz to 10 MHz ± 0.7 ...

  • Agilent Technologies N9010A - page 90

    90 Chapter 3 Option EA3 - Electronic Attenuator , 3.6 GHz Other Electronic Attenuator Specifications ...

  • Agilent Technologies N9010A - page 91

    91 4 Option P03 - Pr eamplifier This chapter contains specificatio ns for the EXA S ignal Analyzer Option P03 preamplifier . ...

  • Agilent Technologies N9010A - page 92

    92 Chapter 4 Option P03 - Preamplifier Specifications Affected by Preamp Specifications Affected by Pr eamp Specification Name Information Frequency Range See “Frequency Range” on page 15 of the core specifications. Nominal Dynami c Range vs. Offset Frequency vs. RBW Does not apply with Preamp On. Measurement Range The measurement range depends ...

  • Agilent Technologies N9010A - page 93

    Chapter 4 93 Option P03 - Preamplifi er Other Preamp Specifications Other Pr eamp Specifications Description Specifications Supplemental I nformation Preamp ( Option P03) a a. The preamp follows the i nput attenuator , AC/DC coupling switch, and precedes the input mixer . In low-band, it follows the 3.6 GHz low-pass filter . Gain Maximum b b. Pream ...

  • Agilent Technologies N9010A - page 94

    94 Chapter 4 Option P03 - Preamplifier Other Preamp Specifications Description Specifications Supplemental Information 1 dB Gain Compression Point (T wo-tone) ab a. Large signals, even at frequencies not shown on the screen, can cause the analyzer to mismeasure on-screen signals because of two-to ne gain compression. This specification tells how la ...

  • Agilent Technologies N9010A - page 95

    Chapter 4 95 Option P03 - Preamplifi er Other Preamp Specifications Description Specifications Supplement al Information Displayed A verage Noise Level (DANL) − Preamp On (Option P03) a a. DANL for zero span and swep t is normalized in two way s and for two reasons. DANL is measured in a 1 kHz RBW and normalized to the narrowest available RBW , b ...

  • Agilent Technologies N9010A - page 96

    96 Chapter 4 Option P03 - Preamplifier Other Preamp Specifications Description Specifications Supplemental Info rmation Frequency Re sponse − Preamp On (Option P03) Refer to the footnote for Band Overlaps o n page 15 . Maximum error relative t o reference condition (50 MHz) Input attenuation 0 dB Swept operation a a. For Sweep T ype = FFT , add t ...

  • Agilent Technologies N9010A - page 97

    Chapter 4 97 Option P03 - Preamplifi er Other Preamp Specifications Nominal VSWR − Preamp On (Plot) Description Specifications Supplemental Information Third Order Intermodulat ion Distort ion T one separation 5 times IF Prefilter Bandwidth a a. See the IF Prefilter Bandwidth table in the specifications for “Gain Compression” on page 42 . Whe ...

  • Agilent Technologies N9010A - page 98

    98 Chapter 4 Option P03 - Preamplifier Other Preamp Specifications Nominal Dynamic Range at 1 GHz, Preamp On (Plot) ...

  • Agilent Technologies N9010A - page 99

    99 5 Option PFR - Pr ecision Fr equency Refer ence This chapter contains specifications for th e Option PFR Precision Frequency Reference. ...

  • Agilent Technologies N9010A - page 100

    100 Chapter 5 Option PFR - Precision Frequency Reference Specifications Affected by Precision Fr equency Refer ence Specifications Affected by Pr ecision Fr equency Reference Specification Name Information Precision Frequency Reference See “Precision Frequency Reference” on page 18 in the core specific ations. ...

  • Agilent Technologies N9010A - page 101

    101 6 I/Q Analyzer This chapter contains specifications for the I/Q Analyzer measurement application (Basic Mode). ...

  • Agilent Technologies N9010A - page 102

    102 Chapter 6 I/Q Analyzer Specifications Affect ed by I/Q Analyzer: Specifications Affected by I/Q Analyzer: Specification Name Information Number of Frequency Display T race Points (buckets) Does not apply . Resolution Bandwidth See “Frequency” on page 103 in this chapter . V ideo Bandwidth N ot avail a ble. Clipping-to-Noise Dynamic Range Se ...

  • Agilent Technologies N9010A - page 103

    Chapter 6 103 I/Q Analyzer Freque ncy Fr equency Description Specifications Supplemental Information Freq uen cy Span S tandard instrument 10 Hz to 10 MHz Option B25 10 Hz to 25 MHz Resolution Bandwidth (Spectrum Measurement) Range Overall Span = 1 MHz Span = 10 kHz Span = 100 Hz 100 mHz to 3 MHz 50 Hz to 1 MHz 1 Hz to 10 kHz 100 mHz to 10 0 Hz W i ...

  • Agilent Technologies N9010A - page 104

    104 Chapter 6 I/Q Analyzer Frequen cy Description Specifications Supplemental In formation Clipping-to-Noise Dynamic Range a a. This specification is defined to be the ratio of the clipping lev el (also known as “ADC Over Ran ge”) to the noise density . In decibel units, it can be defined as clipping_l evel [dBm] − noise_density [dBm/Hz]; the ...

  • Agilent Technologies N9010A - page 105

    Chapter 6 105 I/Q Analyzer Data Acquisition Data Acquisition Description Specifications Supplemental Information Time Record Length 4,000,000 sam ples (max) 4,000,000 samples ≈ 88.89 ms at 25 MHz span Sample Rate 90 MSa/s for 25 MHz ADC Resolutio n 14 Bits ...

  • Agilent Technologies N9010A - page 106

    106 Chapter 6 I/Q Analyzer Data Acquisit ion ...

  • Agilent Technologies N9010A - page 107

    107 7 Phase Noise Measur ement Application This chapter contains specifications for the N9068A Phase Noise measurement application. ...

  • Agilent Technologies N9010A - page 108

    108 Chapter 7 Phase Noise Measurement Application General Specifications General Specifications Description Specifications Supplemental I nformation Maximum Carrier Fr equency EXA Signal Analyzers Option 503 3.6 GHz Option 507 7 GHz Option 513 13.6 GHz Option 526 26.5 GHz Description Specifications Supplemental Information Measurement Characteristi ...

  • Agilent Technologies N9010A - page 109

    Chapter 7 109 Phase Noise Measurement Application General Specifications Description Specifications Supplemental Informat ion Measurement Accuracy Phase Noise Density Accuracy a b Default settings c Overdrive On setting a. This does not include the ef fect of system noise floo r . This error is a fu nction of the signal (phase noise of the DUT) to ...

  • Agilent Technologies N9010A - page 110

    11 0 Chapter 7 Phase Noise Measurement Application General Specifications Description Specifications Supplemental Information Amplitude R epeatability Standard Deviation a b a. Amplitude repeatabilit y is the nominal stan dard de viation of the measured phase noise. This table comes from an observat ion of 30 log plot measurements using a 1 GHz, 0 ...

  • Agilent Technologies N9010A - page 111

    Chapter 7 111 Phase Noise Measurement Application General Specifications Description Specifications Supplemental Inf ormation Offset Frequency Range 3 Hz to ( ƒ opt − ƒ CF ) Hz ƒ opt : Maximum frequency determined by optio n a ƒ CF : Carrier frequency of signal under test a. For example, ƒ opt is 3.6 GHz for Option 503 . Accuracy b b. The fr ...

  • Agilent Technologies N9010A - page 112

    11 2 Chapter 7 Phase Noise Measurement Application General Specifications ...

  • Agilent Technologies N9010A - page 113

    11 3 8 802.16 OFDMA Measur ement Application This chapter contains specifications for the N9075A 802. 16 OFDMA measurement application. Additional Definitions and Requirement s Because digital communications si gnals are noise-like, all measurem ents will have variations. The specifications apply only with adequate averaging to rem ove those variat ...

  • Agilent Technologies N9010A - page 114

    11 4 Chapter 8 802.16 OFDMA Measurement Appli cation Measurement Specifications Measurement Specifications Description Specifications Supplemental Information Channel Power Minimum power at RF Input − 30 dBm (n ominal) Absolute power accuracy a a. Absolute power accuracy includes all error sources for in-band signals except mismatch errors and re ...

  • Agilent Technologies N9010A - page 115

    Chapter 8 11 5 802.16 OFDMA Measurement Application Measurement Specifications Minimum power at RF Input − 36 dBm (nominal) ACPR Accuracy Radio BW Offset MS 5 MHz 5 MHz ± 0.10 dB At ACPR − 24 dBc with optimum mixer level a MS 5 MHz 10 MHz ± 0.45 dB At ACPR − 47 dBc with optimum mixer level b MS 10 MHz 10 MHz ± 0.17 dB At ACPR − 24 dBc wi ...

  • Agilent Technologies N9010A - page 116

    11 6 Chapter 8 802.16 OFDMA Measurement Appli cation Measurement Specifications e. T o meet this specified accuracy when measuring bas e station (BS) at − 45 dBc ACPR, the mixer level (ML) must be optimized for accur acy . This optimum mixer level is − 18 dBm, so the input attenuatio n must be set as close as possible to the average i nput powe ...

  • Agilent Technologies N9010A - page 117

    Chapter 8 11 7 802.16 OFDMA Measurement Application Measurement Specifications Description Specifications Supplemental Information Spectrum Emission Mask Dynamic Range, rel a tiv e 5.05 MHz offset 10 MHz BW a b a. The dynamic range specification is the ratio of the channel pow er to the power in the offset specified. The dynamic range depends on th ...

  • Agilent Technologies N9010A - page 118

    11 8 Chapter 8 802.16 OFDMA Measurement Appli cation Measurement Specifications Frequency Description Specifications Supplemental Information Spurious Emissions Accuracy Attenuation = 10 dB Frequency Range 9 kHz to 3.6 GHz ± 0.38 dB (95 th percentile) 3.5 GHz to 8.4 GHz ± 1.22 dB (95 th percentile) 8.3 GHz to 13.6 GHz ± 1.59 dB (95 th percentile ...

  • Agilent Technologies N9010A - page 119

    11 9 9 W -CDMA Measur ement Application This chapter contains specifications for the N9073A W - CDMA measurement application. It contains both N9073A-1FP W - CDMA and N907 3A-2FP HSDP A/HSUP A me asurement applications. Additional Definitions and Requirement s Because digital communications si gnals are noise-like, all measurem ents will have varia ...

  • Agilent Technologies N9010A - page 120

    120 Chapter 9 W -CDMA Measurement Application Conformance with 3GPP TS 25.141 Base S tati on Requirements Conformance with 3GPP TS 25.141 Base S tation Requir ements Sub- clause Name 3GPP Requir ed T est Instrument T olerance (as of 2006-03) Instrument T olerance Interval abc Supplemental Information S t an da rd sections (Measurement Name) 6.2.1 M ...

  • Agilent Technologies N9010A - page 121

    Chapter 9 121 W -CDMA Measurement Application Conformance with 3GPP TS 25.141 Base S tation Requirements 6.7.3 T ime alignment error in Tx Diversity (Modulation Accuracy) ± 26 ns (95%) [= 0.1 T c] ± 1.25 ns (100%) a. Those tolerances marked as 95% are derived from 95th percentile observat ions with 95% confidence. b. Those tolerances marked as 10 ...

  • Agilent Technologies N9010A - page 122

    122 Chapter 9 W -CDMA Measurement Application Amplitude Amplitude Description Specifications Supplemental Information Channel Power Minimum power at RF Input − 50 dBm (n ominal) Absolute power accuracy a 20 to 30 °C Atten = 10 dB a. Absolute power accuracy includes all error sources for in-band signals except mismatch errors and repeatability du ...

  • Agilent Technologies N9010A - page 123

    Chapter 9 123 W -CDMA Measurement Application Amplitude Description Specifications Supplemental Information Adjacent Channel Power (ACPR; ACLR) Single Carrier Minimum power at RF Input − 36 dBm (nominal) ACPR Accuracy a a. The accuracy of the Adjacent Channel Power Ratio will depend on the m ixer drive level and whether the distortion p roducts f ...

  • Agilent Technologies N9010A - page 124

    124 Chapter 9 W -CDMA Measurement Application Amplitude b. The Fast method has a slight decrease in accuracy in only one case: for BTS measurements at 5 MHz offset, the accuracy degrades by ± 0.01 dB relative to the accuracy shown in this table. c. T o meet this specified accuracy when measuring mobile station (MS) or user equipment (UE) within 3 ...

  • Agilent Technologies N9010A - page 125

    Chapter 9 125 W -CDMA Measurement Application Amplitude Fast ACPR T est a a. Observation conditions for ACP speed: Display Off, signal is T est Model 1 with 64 DPCH, Method set to Fast. Measured with an IBM compat- ible PC with a 3 GHz Pen tium 4 running W indows XP Professional V ersion 2002. The com munications medium was PCI-GPIB IEEE 488.2. T h ...

  • Agilent Technologies N9010A - page 126

    126 Chapter 9 W -CDMA Measurement Application Amplitude Description Specifications Supplemental Information Power S tatistics CCDF Histogram Resolution 0.01 dB a a. The Complementary Cumulative Distribu tion Function (CCDF) is a reformatt ing of the histo gram of the power envelope. The width of the amplitu de bins used by the histogram is the hist ...

  • Agilent Technologies N9010A - page 127

    Chapter 9 127 W -CDMA Measurement Application Amplitude c. The sensitivity is specified with 0 dB input atten uati on. It represents the noise lim itati ons of the ana- lyzer . It is tested without an input signal. The sensitivity at thi s offset is specified in the default 30 kHz RBW , at a center frequency of 2 GHz. d. The relative accuracy is a ...

  • Agilent Technologies N9010A - page 128

    128 Chapter 9 W -CDMA Measurement Application Amplitude Description Specifications Supplemental Information Spurious Emissions T able-driven spurious signals; search across regions Dynamic Range, rel ativ e 93.1 dB 98.4 dB (typical) Sensitivity , absolute − 79.4 dBm − 85.4 dBm (typical) Accuracy Attenuation = 10 dB Frequency Range 9 kHz to 3.6 ...

  • Agilent Technologies N9010A - page 129

    Chapter 9 129 W -CDMA Measurement Application Amplitude Description Specifications Supplemental Information Code Domain BTS Measurements − 25 dBm ≤ ML a ≤ − 15 dBm 20 to 30 °C a. ML (mixer level) is RF input power minus att enuation. RF input power and attenuation are set to meet the Mixer Level range. Code domain power Absolute accuracy ? ...

  • Agilent Technologies N9010A - page 130

    130 Chapter 9 W -CDMA Measurement Application Amplitude Description Specifications Supplement al Information QPSK EVM − 25 dBm ≤ ML a ≤ − 15 dBm 20 to 30 °C a. ML (mixer level) is RF input power minus att enuation. RF input power and attenuation are set to meet the Mixer Level range. EVM Range 0 to 25% Floor 1.6% Accuracy b b. The accuracy ...

  • Agilent Technologies N9010A - page 131

    Chapter 9 131 W -CDMA Measurement Application Amplitude Description Specifications Supplemental Information Modulation Accura cy (Composite EVM) BTS Measurements − 25 dBm ≤ ML a ≤ − 15 dBm 20 to 30 °C a. ML (mixer level) is RF input power minus att enuation. RF input power and attenuation are set to meet the Mixer Level range. Composite EV ...

  • Agilent Technologies N9010A - page 132

    132 Chapter 9 W -CDMA Measurement Application Amplitude d. If 16 QAM and 64 QAM codes ar e included, it is not applicable. e. This specifies a synchronization rang e with CPICH for CPICH only sig nal. f. tfa = transmitter frequency × frequency reference accuracy g. The accuracy specification applies when the measured signal is the combin ation of ...

  • Agilent Technologies N9010A - page 133

    Chapter 9 133 W -CDMA Measurement Application Freque ncy Fr equency Description Specifications Supplemental Information In-Band Frequency Range Operating Band UL Frequencies UE transmit, Node B receive DL Frequencies UE receive, Node B transmit I 1920 − 1980 MHz 21 10 − 2170 MHz II 1 850 − 1910 MHz 1930 − 1990 MHz III 1710 − 178 5 MHz 180 ...

  • Agilent Technologies N9010A - page 134

    134 Chapter 9 W -CDMA Measurement Application Frequen cy ...

  • Agilent Technologies N9010A - page 135

    135 10 GSM/EDGE Measur ement Application This chapter contains specifications for the N9071A GSM/EDGE Measurement Application. For EDGE Evolution (EGPRS2) including Normal Burst (16 QAM/32QAM) and High Symbol Rate (HSR) Burst, Option 3FP is required . Additional Definitions and Requirement s Because digital communications si gnals are noise-like, a ...

  • Agilent Technologies N9010A - page 136

    136 Chapter 10 GSM/EDGE Measurem ent Application Measurements Measurements Description Specifications Supplemental Information EDGE Error V ector Magnitude (EVM) 3 π /8 shifted 8PSK modulation, 3 π /4 shifted QPSK, π /4 shifted 16QAM, – π /4 shifted 32QA M modulation in NSR /HSR with pulse shaping filter . Specifications based on 200 bursts C ...

  • Agilent Technologies N9010A - page 137

    Chapter 10 137 GSM/EDGE Measurement Application Measurements e. The accuracy specification applies wh en the Burst Sync is set to Trai ning Sequence, and T rigger is set to External T rigger . Description Specifications Supplemental Information Power vs. Time and EDGE Power vs. Ti me GMSK modu lation (GSM) 3 π /8 shifted 8PSK mo dulation, 3 π /4 ...

  • Agilent Technologies N9010A - page 138

    138 Chapter 10 GSM/EDGE Measurem ent Application Measurements Description Specifications Supplemental Information Phase and Frequency Err or GMSK modulation (GSM) Specifications based on 3GPP essential conformance requirements, and 200 bursts Carrier power range at RF Input + 27 to − 45 dBm (nominal) Phase error a , rms a. Phase error and frequen ...

  • Agilent Technologies N9010A - page 139

    Chapter 10 139 GSM/EDGE Measurement Application Measurements Description Specifications Supplemental Information Output RF Spectrum (ORFS) and EDGE Output RF Spectrum GMSK modulation (GSM) 3 π /8 shifted 8PSK modulation, 3 π /4 shifted QPSK, π /4 shifted 16QAM, – π /4 shifted 32QAM modulation in NSR/HSR (EDGE) Minimum carrier po wer at RF Inp ...

  • Agilent Technologies N9010A - page 140

    140 Chapter 10 GSM/EDGE Measurem ent Application Measurements Description Specifications Supplemental Information ORFS and EDGE ORFS (contin ued) Dynamic Range, Spectrum due to modulation a a. Maximum dynamic range requires RF i nput power above − 2 dBm for offsets of 1.2 MHz and below fo r GSM, and above − 5 dBm for EDGE. For offsets of 1.8 MH ...

  • Agilent Technologies N9010A - page 141

    Chapter 10 141 GSM/EDGE Measurement Application Measurements b. ORFS standards call for the use of a 5-pole, sync-tun ed filter; this and t he fo llowing footnotes review the instrument's conformance to that standard. Of fs et frequencies can be measured by using either the FFT method or the direct time method. By default, the FFT metho d is u ...

  • Agilent Technologies N9010A - page 142

    142 Chapter 10 GSM/EDGE Measurem ent Application Frequency Ranges Fr equency Ranges Description Uplink Downlink Supplemental Information In-Band Fr equency Ranges P-GSM 900 89 0 to 915 MHz 935 to 960 MHz E-GSM 900 880 to 915 MHz 925 to 960 MHz R-GSM 900 876 to 915 MHz 921 to 960 MHz DCS1800 17 10 to 1785 MHz 1805 to 1880 MHz PCS1900 1850 to 1910 MH ...

  • Agilent Technologies N9010A - page 143

    143 11 Analog Demodulation Measur ement Application This chapter contains specifications for the N906 3A Analog Demodulati on Measu rement Applic ation. ...

  • Agilent Technologies N9010A - page 144

    144 Chapter 1 1 Analog Demodulation Measurement Ap plication Analog Demodulation Perf ormance – Pre-Demodulation Analog Demodulation Performance – Pr e-Demodulation Description Specifications Supplemental Informat ion Maximum Safe Input Level A verage T o tal Power + 30 dBm (1 W) Peak Pulse Power < 10 μ s pulse width, < 1 % duty cycle, I ...

  • Agilent Technologies N9010A - page 145

    Chapter 1 1 145 Analog Demodu l ation M easurement Application Analog Demodula tion Perfor mance – Post-Demodulation Analog Demodulation Performance – Post-Demodulation Description Specifications Supplemental Informatio n Maximum Audio Frequency Span 4 MHz Filters Low Pass High Pass Band Pass Deemphasis 300 Hz, 3 kHz, 15 kHz, 30 kHz, 80 kHz, 30 ...

  • Agilent Technologies N9010A - page 146

    146 Chapter 1 1 Analog Demodulation Measurement Ap plication Frequency Modulatio n - Level and Carrier Metrics Fr equency Modulation - Level and Carrier Metrics Description Specifications Supplemental Information FM Deviation Accuracy Rate: 1 kHz - 1 MH z, Deviation: 1 - 100 kHz a a. For optimum measu rement of rate and deviation, ensure that the c ...

  • Agilent Technologies N9010A - page 147

    Chapter 1 1 147 Analog Demodu l ation M easurement Application Frequency Modulation - Distortion Fr equency Modulation - Distortion Description Specifications Supplemental Information Residual Rate: 1 - 10 kHz, Deviation: 5 kHz THD Distortion SINAD 0.2% (nominal) 3% (nominal) 32 dB (nominal) Absolute Accuracy Rate: 1 - 10 kHz, Deviation: 5 kHz THD ...

  • Agilent Technologies N9010A - page 148

    148 Chapter 1 1 Analog Demodulation Measurement Ap plication Frequency Modulation - Distort ion Measurement Range Rate: 1 - 10 kHz, Deviation: 5 kHz THD Distortion SINA D residual to 100 % (nominal) Measured 2nd and 3rd harmonics Measurement includes at most 10 harmonics residual to 100 % (nominal) 0 dB to residual (nominal) Description Specificati ...

  • Agilent Technologies N9010A - page 149

    Chapter 1 1 149 Analog Demodu l ation M easurement Application Amplitude Modulation - Level and Carrier Metrics Amplitude Modulation - Level and Carrier Metrics Description Specifications Supplemental Inform ation AM Depth Accuracy Rate: 1 kHz - 1 MHz ± 0.2 % + 0.002 × measured value (nominal) AM Rate Accuracy Rate: 1 kHz - 1 MHz ± 0.05 Hz (nomi ...

  • Agilent Technologies N9010A - page 150

    150 Chapter 1 1 Analog Demodulation Measurement Ap plication Amplitude Modulation - Distortion Amplitude Modulation - Distortion Description Specifications Supplemental Informat ion Residual Depth: 50 % Rate: 1 - 10 kHz THD Distortion SINA D 0.16 % (nominal) 0.3 % (nominal) 50 dB (nominal) Absolute Accuracy Depth: 50 % Rate: 1 - 10 kHz THD Distorti ...

  • Agilent Technologies N9010A - page 151

    Chapter 1 1 151 Analog Demodu l ation M easurement Application Phase Modulation - Level and Carrier Metrics Phase Modulation - Level and Carrier Metrics Description Specifications Supplemental Informat ion PM Deviation Accuracy Rate: 1 - 20 kHz Deviation: 0.2 t o 6 rad ± 100 % × (0.005 + (rate/1 MHz) ) (nominal) PM Rate Accuracy Rate: 1 - 10 kHz ...

  • Agilent Technologies N9010A - page 152

    152 Chapter 1 1 Analog Demodulation Measurement Ap plication Phase Modulation - Distortion Phase Modulation - Distortion Description Specifi cations Supplemental Information Residual Rate: 1 - 10 kHz, Deviation: 628 mrad THD Distortion SINA D 0.1 % (nominal) 0.8 % (nominal) 42 dB (nominal) Absolute Accuracy THD Distortion SINA D Rate: 1 - 10 kHz, D ...

  • Agilent Technologies N9010A - page 153

    153 12 Noise Figur e Measur ement Application This chapter contains specifications for the N9069A Noise Figure M easurement Application. ...

  • Agilent Technologies N9010A - page 154

    154 Chapter 12 Noise Figure Measurement Application General Specifications General Specifications Description Specifications Supplemental Information Noise Figure Uncertainty Calculator a a. The figures given in the table are for the uncertainty added by the X-Se ries Signal Anal yzer instrument only . T o compute the total uncertainty for your noi ...

  • Agilent Technologies N9010A - page 155

    Chapter 12 155 Noise Figure Measurement Application General Specifications e. Noise figure measurements can be made in this ra nge but will often be poor because of the lack of availability of built-in pream plification. For high gain DUT s or with the use of an external preamplifier , this problem can be overcome. In such cases, the In strument Un ...

  • Agilent Technologies N9010A - page 156

    156 Chapter 12 Noise Figure Measurement Application General Specifications Description Specifications Supplemental Information Gain Instrumen t Un cer tainty a a. “Instrument Uncertain ty” is defined for gain measurements as uncertainty due to relative amplitude uncertainties encountered in the analyzer when making the m easurements required fo ...

  • Agilent Technologies N9010A - page 157

    Chapter 12 157 Noise Figure Measurement Application General Specifications Description Specifications Supplemental Information Noise Figure Uncertainty Calculator a a. The Noise Figure Uncertainty Calculator requires the parameters shown in order to calculate the total uncertainty of a Nois e Figure measurement. Instrument Noise Fig ure Un certaint ...

  • Agilent Technologies N9010A - page 158

    158 Chapter 12 Noise Figure Measurement Application General Specifications Nominal Instru ment Noise Figure ...

  • Agilent Technologies N9010A - page 159

    Chapter 12 159 Noise Figure Measurement Application General Specifications Nominal Instrument Input VSWR, DC Coupled ...

  • Agilent Technologies N9010A - page 160

    160 Chapter 12 Noise Figure Measurement Application General Specifications ...

  • Agilent Technologies N9010A - page 161

    161 13 cdma2000 Measur ement Application This chapter contains specifications for the X-Se ries Signal Analyzer N9072A, cdma2000 measurement application. Additional Definitions and Requir ements Because digital communications si gnals are noise-like, all measurem ents will have variations. The specifications apply only with adequate averaging to re ...

  • Agilent Technologies N9010A - page 162

    162 Chapter 13 cdma2000 Measurement Application Measurements Measurements Description Specifications Supplemental Information Channel Power 1.23 MHz Integration BW Minimum power at RF input − 50 dBm (nom inal) Absolute power accuracy a 20 to 30 ° C Atten = 10 dB 95 % Confidence Absolute power accuracy 20 to 30 ° C Atten = 10 dB a. Absolute powe ...

  • Agilent Technologies N9010A - page 163

    Chapter 13 163 cdma2000 Measurem ent Application Measurements Description Specifications Supplemental Information Adjacent Channel Power a a. ACP test items compliance the limits of conducted spurious emission specification defined in 3GPP2 standards Minimum power at RF input − 36 dBm (nominal) Dynamic range Referenced to average power of carrier ...

  • Agilent Technologies N9010A - page 164

    164 Chapter 13 cdma2000 Measurement Application Measurements a. The Complementary Cumu lative Distribution Function (CCDF) i s a reformatting of a hist ogram of the power envelope. The width of the amplitude bins used by the histo gram is the histogram resolution. The resolution of the CCDF will be the same as the width of those bins. Description S ...

  • Agilent Technologies N9010A - page 165

    Chapter 13 165 cdma2000 Measurem ent Application Measurements Description Specifications Supplemental Information Spectrum Emission Mask a a. SEM test items compliance the limits of conduct ed spurious emission specification defi ned in 3GPP2 standards Dynamic Range, rela tiv e 750 kHz o ffset 73.6 dB 81.0 dB (typical) 1980 kHz offset 78.3 dB 83.9 ...

  • Agilent Technologies N9010A - page 166

    166 Chapter 13 cdma2000 Measurement Application Measurements Description Specifications Supplemental Information Code Domain BTS Measurements − 25 dBm ≤ ML a ≤ − 15 dBm 20 to 30 ° C a. ML (mixer level) is RF input power minus att enuation RF input power ra nge is accordingly determined to m eet Mixer level. Code domain power Relative power ...

  • Agilent Technologies N9010A - page 167

    Chapter 13 167 cdma2000 Measurem ent Application Measurements Description Specifications Supplemental Information QPSK EVM − 25 dBm ≤ ML a ≤ − 15 dBm 20 to 30 ° C a. ML (mixer level) is RF input power minus att enuation RF input power range is accordingly determined to meet Mixer level . EVM Range 0 to 25 % Floor 1.6 % Accuracy b b. The ac ...

  • Agilent Technologies N9010A - page 168

    168 Chapter 13 cdma2000 Measurement Application Measurements Description Specifications Supplemental Informat ion Modulation Accura cy (Composite Rho) BTS Measurements − 25 dBm ≤ ML a ≤ − 15 dBm 20 to 30 ° C a. ML (mixer level) is RF input power minus att enuation RF input power range is according ly determined to meet Mixer level. Specifi ...

  • Agilent Technologies N9010A - page 169

    Chapter 13 169 cdma2000 Measurem ent Application Measurements Description Specifications Supplemental Information Pilot time offset Range − 13.33 to +13.33 ms From even second signal to start of PN sequence Accuracy ± 300 ns Resolution 10 ns Code domain timing Range ± 200 ns Pilot to cod e channel time tole ra nce Accuracy ± 1. 25 ns Resolutio ...

  • Agilent Technologies N9010A - page 170

    170 Chapter 13 cdma2000 Measurement Application Frequency Range Fr equency Range Description Specifica tions Supplemental Information In-Band Fr equency Range Band Class 0 (North American Cellular) 869 to 89 4 MHz 824 to 849 MHz Band Class 1 (North American PCS) 1930 to 1990 MHz 1850 to 1910 MHz Band Class 2 (T ACS) 917 to 960 MHz 872 to 915 MHz Ba ...

  • Agilent Technologies N9010A - page 171

    171 14 1xEV -DO Measur ement Application This chapter contains specifications for the X- Series, N9076A, 1xEV -DO measurement application. Additional Definitions and Requir ements Because digital communications si gnals are noise-like, all measurem ents will have variations. The specifications apply only with adequate averaging to rem ove those var ...

  • Agilent Technologies N9010A - page 172

    172 Chapter 14 1xEV -DO Measurement Application Measurements Measurements Description Specifications Supplemental Information Channel Power 1.23 MH z Integration BW Input signal m ust not be bursted Minimum power at RF input − 50 dBm (nominal) Absolute power accuracy a 20 to 30 ° C a. Absolute power accuracy includes all error sources for in-ban ...

  • Agilent Technologies N9010A - page 173

    Chapter 14 173 1xEV -DO Measurement Application Measurements Description Specifications Supplemental Information Power S tatistics CCDF Minimum power at RF Input − 40 dBm (no minal) Histogram Resolution 0.01 dB a a. The Complementary Cumulative Dist ribution Function (CCDF) is a reformattin g of a histogram of the power envelope. The width of the ...

  • Agilent Technologies N9010A - page 174

    174 Chapter 14 1xEV -DO Measurement Application Measurements Description Specifications Supplemental Information Spectrum Emission Mask and Adjacent Channel Power Minimum power at RF Input − 20 dBm (nominal) Dynamic Range, rel a tiv e a a. The dynamic range specification is the ratio of the channel power to the po wer in the offset specified. The ...

  • Agilent Technologies N9010A - page 175

    Chapter 14 175 1xEV -DO Measurement Application Measurements Description Specifications Supplemental Informat ion Spurious Emissions Dynamic Range, relative 91.9 dB 97.1 dB (typical) Sensitivity , absolute − 79.4 dBm − 85.4 dB m (typical) Accuracy , absolute 20 Hz t o 3.6 GHz ± 0.38 dB (95% confidence) 3.5 GHz to 8.4 GHz ± 1.22 dB (95% confid ...

  • Agilent Technologies N9010A - page 176

    176 Chapter 14 1xEV -DO Measurement Application Measurements Description Specifications Supplemental I nformation Code Domain BTS Measurements − 25 dBm ≤ ML a ≤ − 15 dBm 20 to 30 °C a. ML (mixer level) is RF input power minus att enuation. For pilot, 2 MAC channels, and 16 channels of QPSK data. Absolute power accuracy ± 0.15 dB ...

  • Agilent Technologies N9010A - page 177

    Chapter 14 177 1xEV -DO Measurement Application Measurements Description Specifications Supplemental Informatio n Modulation Accuracy (Composite Rho) − 25 dBm ≤ ML a ≤ − 15 dBm 20 to 30 °C a. ML (mixer level) is RF input power minus att enuation. For pilot, 2 MAC ch annels, and 16 channels of QPSK data Composite EVM Operating Range 0 to 25 ...

  • Agilent Technologies N9010A - page 178

    178 Chapter 14 1xEV -DO Measurement Application Frequency Range Fr equency Range Description Specifications Supplemental Information In-Band Fr equency Range (Access Network Only) Band Class 0 869 to 894 MHz North American and Korean Cellular Bands Band Class 1 1930 to 1990 MHz North American PCS Band Band Class 2 917 to 960 MHz T ACS Band Band Cla ...

  • Agilent Technologies N9010A - page 179

    179 15 TD-SCDMA Measur ement Application This chapter contains specifications for the X-Series Signal Analyzer N9079A, TD-SCDMA measurement application. It co ntains both N9079A-1FP TD-SCDMA and N9079A-2FP HSP A/8PSK measurement application. Additional Definitions and Requir ements Because digital communications si gnals are noise-like, all measure ...

  • Agilent Technologies N9010A - page 180

    180 Chapter 15 TD-SCDMA Measurement Application Measurements Measurements Description Specification Supplemental Inf ormation Power vs. Time Burst T ype T raf fic, UpP TS and DwP TS T ransmit power Min, Max, Mean Dynamic range 1 14.3 dB A veraging type Off, RMS, Log Measurement ti me Up to 9 slots T rigger type External1, External2, RF Burst Descri ...

  • Agilent Technologies N9010A - page 181

    Chapter 15 181 TD-SCDMA Measurem ent Application Measurements Description Specification Supplemental Information Adjacent Channel Power Single Carrier Minimum Power at RF Input − 36 dBm (nominal) ACPR Accuracy a a. The accuracy of the Adjacent Channel Power Ratio will depend on the m ixer drive level and whether the distortion p roducts from the ...

  • Agilent Technologies N9010A - page 182

    182 Chapter 15 TD-SCDMA Measurement Application Measurements Description Specification Supplemental Inf ormation Power S tatistics CCDF Histogram Resolution 0.01 dB a a. The Complementary Cumulative Distribu tion Function (CCDF) is a reformatt ing of the histo gram of the power envelope. The width of th e amplitude bins used by the histogram is the ...

  • Agilent Technologies N9010A - page 183

    Chapter 15 183 TD-SCDMA Measurem ent Application Measurements Description Specification Supplemental Inf ormation Spectrum Emission Mask Dynamic Range, rel a tiv e 815 kHz offs et ab a. The dynamic range specification is the ratio of the channel pow er to the power in the offset specified. The dynamic range depends on the measurement settings, such ...

  • Agilent Technologies N9010A - page 184

    184 Chapter 15 TD-SCDMA Measurement Application Measurements Description Specification Supplemental Inf ormation Spurious Emissions Dynamic Range, rela tiv e 91.9 dB 97.1 dB (typical) Sensitivity , absolute − 79.4 dBm − 85.4 dBm (typical) Accuracy Attenuation = 10 dB Frequency Range 9 kHz to 3.6 GHz ± 0.38 dB ( 95 % confidence) 3.5 GHz to 7.0 ...

  • Agilent Technologies N9010A - page 185

    Chapter 15 185 TD-SCDMA Measurem ent Application Measurements Description Specification Supplemental Inf ormation Code Domain BTS Measurements − 25 dBm ≤ ML a ≤ − 15 dBm 20 to 30 ° C RF input power range is accordingly determined to meet Mixer level. Code Domain Power Absolute Accuracy − 10 dBc DPCH (Atten = 10 dB) b ± 0. 32 dB (9 5 % c ...

  • Agilent Technologies N9010A - page 186

    186 Chapter 15 TD-SCDMA Measurement Application Measurements − 20 to − 30 dBc ± 0.32 dB Symbol error vector magnitude Accuracy DPCH Channel 0 to − 25 d Bc ± 1.1 % (nominal) HS-PDSCH Channel 0 to − 25 d Bc ± 1.2 % (nominal) a. ML (mixer level) is RF input power minus att enuation. b. Code Domain Power Absolute accuracy is calculated as su ...

  • Agilent Technologies N9010A - page 187

    Chapter 15 187 TD-SCDMA Measurem ent Application Measurements Description Specification Supplemental Inf ormation Modulation Accura cy (Composite EVM) BTS Measurements − 25 dBm ≤ ML a ≤ − 15 dBm 20 to 30 ° C RF input power range is accordingly determined to meet Mixer level. Composite EVM Range T est signal with TS0 active and one DPCH in ...

  • Agilent Technologies N9010A - page 188

    188 Chapter 15 TD-SCDMA Measurement Application Measurements T est signal with TS0 active and one HS-PDSCH in TS0 ± 6 Hz + tfa (nominal) a. ML (mixer level) is RF input power minus att enuation. b. The EVM floor is derived fo r signal power − 20 dBm. The signal has on ly 1 DPCH or HS-PDSCH in TS0. c. The accuracy specification applies when the E ...

  • Agilent Technologies N9010A - page 189

    Chapter 15 189 TD-SCDMA Measurem ent Application Frequency Range Fr equency Range Description Specification Supplemental Information In-Band Fr equency Range O p erat ing Band F requencies I 1900 to 192 0 MHz 2010 to 2025 MHz II 185 0 to 1910 MHz 1930 to 1990 MHz III 1910 to 1930 MHz ...

  • Agilent Technologies N9010A - page 190

    190 Chapter 15 TD-SCDMA Measurement Application Frequency Range ...

  • Agilent Technologies N9010A - page 191

    191 16 L TE Measur ement Application This chapter contains specifications for the N908 0A L TE measurement application and Preliminary specifications for the N9082A measurement applic ations. The only difference between these two applications is the Power vs. T ime measurement is included in th e N9082A and not in the N9080A. Additional Definitions ...

  • Agilent Technologies N9010A - page 192

    192 Chapter 16 L TE Measurement Application Supported Air In terface Featur es Supported Air Interface Features Description Specific ations Supplement al Information 3GPP S tandards Sup ported 36.21 1 V8.6.0 (2009-03) 36.212 V8.6 .0 (2009-03) 36.213 V8.6 .0 (2009-03) 36.101 V8.5 .1 (2009-03) 36.104 V8.5 .0 (2009-03) 36.141 V8.2 .0 (2009-03) 36.521- ...

  • Agilent Technologies N9010A - page 193

    Chapter 16 193 L TE Measurement Application Measurements Measurements Description Specifica tions Supplement al Information Channel Power Minimum power at RF input − 50 dBm (nom inal) Absolute power accuracy a 20 to 30 ° C Atten = 10 dB a. Absolute power accuracy includes all error sources for in-band signals except mismatch errors and repeatabi ...

  • Agilent Technologies N9010A - page 194

    194 Chapter 16 L TE Measurement Application Measurements Description Spec ifications Supplement al Information Adjacent Channel Power Single Channel Minimum power at RF input − 50 dBm (nominal) Accuracy Channel Bandwidth Radio Offset 5 MHz 10 MHz 20 MHz ACPR Range for Spec ification MS Adjacent a ± 0.15 dB ± 0.21 dB ± 0.36 dB − 33 to − 27 ...

  • Agilent Technologies N9010A - page 195

    Chapter 16 195 L TE Measurement Application Measurements Description Sp ecification Supplement al Inform ation Occupied Bandwidth Minimum carrier power at RF Input − 30 dBm (nominal) Frequency accura cy ±10 kHz RBW = 30 kHz, Number of Points = 1001, Span = 10 MHz Description Spec ifications Supplement al Information Spectrum Emission Mask Offset ...

  • Agilent Technologies N9010A - page 196

    196 Chapter 16 L TE Measurement Application Modulation Analysis Specifications Modulation Analysis Specifications Description Specifica tions Supplement al Information EVM Input Range 0 dBm, signal level within one range step of overload Residual EVM Floor a for Downlink (OFDMA) a. Overall EVM and Data EVM using 3GPP standard-d efined calculation. ...

  • Agilent Technologies N9010A - page 197

    Chapter 16 197 L TE Measurement Application In-Band Frequ ency Range In-Band Frequency Range Operating Band, FDD Uplink Downlink 1 1920 to 1980 MHz 211 0 to 2170 MHz 2 1850 to 1910 MHz 1930 to 1990 MHz 3 1710 to 1785 MHz 1805 to 1880 MHz 4 1710 to 1755 MHz 211 0 to 2155 MHz 5 824 to 849 MHz 869 to 894 MHz 6 830 to 840 MHz 875 to 885 MHz 7 2500 to 2 ...

  • Agilent Technologies N9010A - page 198

    198 Chapter 16 L TE Measurement Application In-Band Fr equency Range ...

  • Agilent Technologies N9010A - page 199

    199 17 Single Acquisition Combined Fixed W iMAX Measur ement Application This chapter contains specificatio ns for the EXA S ignal Analyzer N9074A , Combined Fixed W iMAX measurement application. Additional Definitions and Requirement s Because digital communications si gnals are noise-like, all measurem ents will have variations. The specification ...

  • Agilent Technologies N9010A - page 200

    200 Chapter 17 Single Acquisition Combined Fixed WiMAX Measurement Application N9074A-XFP , Single Acquisition Co mbined Fixed WiMAX Measurements N9074A-XFP , Single Acquisition Combined Fixed W iMAX Measur ements Description Specifications Supplemental Informatio n T ransmit Power Input signal must not be burst ed 10 MHz Integration BW Minimum pow ...

  • Agilent Technologies N9010A - page 201

    Chapter 17 201 Single Acquisition Combined Fi xed WiMAX Measurement Application N9074A-XFP , Singl e Acquisition Combined Fi xed WiMAX Measur ements d. The relative accuracy is a measure of the ratio of the power at the of fs et to the main channel power . It applies for spectrum emission levels in the offsets that are well above the dynamic range ...

  • Agilent Technologies N9010A - page 202

    202 Chapter 17 Single Acquisition Combined Fixed WiMAX Measurement Application N9074A-XFP , Single Acquisition Co mbined Fixed WiMAX Measurements ...

  • Agilent Technologies N9010A - page 203

    203 18 Single Acquisition Combined WLAN Measur ement Application This chapter contains specificatio ns for the EXA S ignal Analyzer N9077A , Combined WLAN measurement application. Additional Definitions and Requirement s Because digital communications si gnals are noise-like, all measurem ents will have variations. The specifications for dynamic ra ...

  • Agilent Technologies N9010A - page 204

    204 Chapter 18 Single Acquisition Combined WL AN Measurement Application N9077A, Combined WLAN 802.1 1a or 802.1 1g-OF DM Measurements N9077A, Combined WLAN 802.1 1a or 802.1 1g-OFDM Measurements Description Specifications Supplemental Informatio n T ransmit Power Input signal must not be burst ed 18 MHz Integration BW Minimum power at RF Input – ...

  • Agilent Technologies N9010A - page 205

    Chapter 18 205 Single Acquisition Combined WL AN Measurement Application N9077A, Combined WLAN 802.1 1 a or 802.1 1g-OFDM Measurements Absolute 20 – 30°C ±1.58 dB 30 MHz offset Dynamic Range, rela tiv e 67.5 dB (nominal) Sensitivity , absol ute –80.7 dBm (nominal) Accuracy Relative ±0.66 dB Absolute 20 – 30°C ±1.60 dB a. The dynamic rang ...

  • Agilent Technologies N9010A - page 206

    206 Chapter 18 Single Acquisition Combined WL AN Measurement Application N9077A, Combined WLAN 802.1 1a or 802.1 1g-OF DM Measurements Center Frequency Leakage UUT Maximum Leakage –10 dBc (nominal) Analyzer Noise Floor –45 dBc (nominal) Frequency Range ±100 kHz (nomin al) Accuracy ±10 Hz+tfa c a. ML (mixer level) is RF input po wer mi nus att ...

  • Agilent Technologies N9010A - page 207

    Chapter 18 207 Single Acquisition Combined WL AN Measurement Application N9077A, Combined WLAN 802.1 1b or 802.1 1g-DSSS Measurements N9077A, Combined WLAN 802.1 1b or 802.1 1g-DSSS Measurements Description Specifications Supplemental Informatio n T ransmit Power Input signal must not be burst ed 22 MHz Integration BW Minimum power at RF Input –5 ...

  • Agilent Technologies N9010A - page 208

    208 Chapter 18 Single Acquisition Combined WL AN Measurement Application N9077A, Combined WLAN 802.1 1b or 802.1 1g-DSSS Measurements Absolute 20 – 30°C ±1.59 dB 33 MHz offset Dynamic Range, rel a tiv e f 68.3 dB (nominal) Sensitivity , absol ute –80.7 dBm (nominal) Accuracy Relative ±0.68 dB Absolute 20 – 30°C ±1.60 dB a. The dynamic ra ...

  • Agilent Technologies N9010A - page 209

    Chapter 18 209 Single Acquisition Combined WL AN Measurement Application N9077A, Combined WLAN 802.1 1b or 802.1 1g-DSSS Measurements Currier Suppression UUT Maximum Suppression –10 dBc (nominal) Analyzer Noise Floor –46 dBc (nominal) Frequency Range ±100 kHz (nomin al) Accuracy ±10 Hz+tfa c a. ML (mixer level) is RF input po wer m inus atten ...

  • Agilent Technologies N9010A - page 210

    210 Chapter 18 Single Acquisition Combined WL AN Measurement Application N9077A, Combined WLAN 802.1 1b or 802.1 1g-DSSS Measurements ...

  • Agilent Technologies N9010A - page 211

    21 1 19 iDEN/W iDEN/MotoT alk Measur ement Application This chapter contains specifications for the N6149A , iDEN/W iDEN/MotoT alk Measurement Application. Additional Definitions and Requirement s Because digital communications si gnals are noise-like, all measurem ents will have variations. The specifications apply only with adequate averaging to ...

  • Agilent Technologies N9010A - page 212

    212 Chapter 19 iDEN/W iDEN/MotoT alk Measurement Application Freq uen cy and Ti me Fr equency and T ime Description Specifications Supplemental Informat ion Frequency and T ime-related Specifications Please refer to “Frequency and T ime” on page 15 ...

  • Agilent Technologies N9010A - page 213

    Chapter 19 213 iDEN/W iDEN/MotoT alk M easurement Application Amplitude Accuracy and Range Amplitude Accuracy and Range Dynamic Range Description Specifications Supplemental Informatio n Amplitude an d Range-relat ed Specifications Please refer to “Amplitude Accuracy and Range” on page 29 . Description Specifications Supplemental Information Dy ...

  • Agilent Technologies N9010A - page 214

    214 Chapter 19 iDEN/W iDEN/MotoT alk Measurement Application Application Specifications Application Specifications Description Specifications Supplemental Information Measurements iDEN Power ACP (adjace nt channel power) Occupied Bandwidth Includes Carrier Power on summary data screen iDEN Demod PvT (power versus time) Modulation analysis BER (bit ...

  • Agilent Technologies N9010A - page 215

    Chapter 19 215 iDEN/W iDEN/MotoT alk M easurement Application Applicat ion Sp ecifications Description Specifications Supplemental Information iDEN Power Supported Formats iDEN single carrier TDMA W iDEN- multiple carrier TDMA Pass/Fail T ests Occupied Bandwidth (OB W) Adjacent Channel Power (ACP) Carrier Configuration 25 kH z W iDEN 50 kHz WiDEN 7 ...

  • Agilent Technologies N9010A - page 216

    216 Chapter 19 iDEN/W iDEN/MotoT alk Measurement Application Application Specifications Composite EVM Floor a 1.4% (no minal) Measurement Parameters Search Length Normalize IQ and FSK waveforms Measurement Parameters (advanced) Gaussian BT Symbol Rate Burst Search on/of f Bandwidth Time product Result Displays Slot Error V ector T ime Slot Error Su ...

  • Agilent Technologies N9010A - page 217

    217 20 DVB-T/H Measur ement Application This chapter contains specificatio ns for the EXA S ignal Analyzer N6153A , DVB-T/H measurement application. Additional Definitions and Requirement s Because digital communications si gnals are noise-like, all measurem ents will have variations. The specifications apply only with adequate averaging to rem ove ...

  • Agilent Technologies N9010A - page 218

    218 Chapter 20 DVB-T/H Measurement Application N6153A, DVB-T/H Measurements Application N6153A, DVB-T/H Measurements Application Description Specifications Supplemental Informatio n Channel Power Input signal must not be burst ed 7.61 MHz Integration BW Minimum power at RF Input –50 dBm (nominal) Absolute Power Accuracy a 20 to 30 °C a. Absolute ...

  • Agilent Technologies N9010A - page 219

    Chapter 20 219 DVB-T/H Measurement Application N6153A, DVB-T/H Me asur ements Applic at ion a. The Complementary Cum ulative Distribution Func tion (CCDF) is a reformattin g of a histogram of the power envelope. The width of the amplitude bin s used by the histo gram is the histo gram resolution. The resolution of the CCDF will be the same as the w ...

  • Agilent Technologies N9010A - page 220

    220 Chapter 20 DVB-T/H Measurement Application N6153A, DVB-T/H Measurements Application Sensitivity , absol ute –105.5 dBm – 1 1 1.5 dBm (typical) Accuracy Relative ±0.63 dB Absolute 20 – 30°C ±1.05 dB a. The dynamic range specification is the r atio of the ch annel power to the power in the of fset specified. The dynamic range depends on ...

  • Agilent Technologies N9010A - page 221

    Chapter 20 221 DVB-T/H Measurement Application N6153A, DVB-T/H Me asur ements Applic at ion Description Specifications Supplemental Information 64 QAM EVM ML a = –20 dBm 20 to 30 °C FFT Size = 2048, GuardInterval = 1/32, alpha = 1 EVM Operating range 0 to 8% Floor 0.64% (blind equalizer ON) 0.73% (blind equalizer OFF) Accuracy from 0.7% to 1 .2% ...

  • Agilent Technologies N9010A - page 222

    222 Chapter 20 DVB-T/H Measurement Application N6153A, DVB-T/H Measurements Application Accuracy ±0.50% BER Before V iterbi Range 0 to 1.0×10 –1 Resolution 0.01×10 –exp onet BER Before Reed-Solomon Range 0 to 1.0×10 –3 Resolution 0.01×10 –exp onet BER After Reed-Solomon Range 0 to inf Resolution 1 a. ML (mixer level) is RF input po wer ...

  • Agilent Technologies N9010A - page 223

    223 21 ISDB-T Measur ement Application This chapter contains specificatio ns for the EXA S ignal Analyzer N6155A , ISDB-T measurement application. Additional Definitions and Requirement s Because digital communications si gnals are noise-like, all measurem ents will have variations. The specifications apply only with adequate averaging to rem ove t ...

  • Agilent Technologies N9010A - page 224

    224 Chapter 21 ISDB-T Measurement Application N6155A, ISDB-T/ TSB Measurement Applicati on N6155A, ISDB-T/T SB Measurement Application Description Specifications Supplemental Informatio n Channel Power Input signal must not be burst ed 5.6 MHz Integration BW Minimum power at RF Input –50 dBm (nominal) Absolute Power Accuracy a 20 to 30 °C a. Abs ...

  • Agilent Technologies N9010A - page 225

    Chapter 21 225 ISDB-T Measurement Application N6155A, ISDB- T/TSB Measur ement Applicatio n Description Specifications Supplemental I nformation Power S tatistics CCDF Minimum power at RF Input –50 dBm (nominal) Histogram Resolution 0.01 dB a a. The Complementary Cumulative Di stribution Function (CCDF) is a reformatting of a histogram of the pow ...

  • Agilent Technologies N9010A - page 226

    226 Chapter 21 ISDB-T Measurement Application N6155A, ISDB-T/ TSB Measurement Applicati on Description Specifications Supplemental Information Spectrum Emission Mask Limit T ype • Manual • JEIT A (ARIB-B 31) according to P ≤ 0.025 W ; 0.025 W < P ≤ 0.25 W ; 0.25 W < P ≤ 2.5 W ; P > 2.5 W (P is the channel power) • ABNT Non-Crit ...

  • Agilent Technologies N9010A - page 227

    Chapter 21 227 ISDB-T Measurement Application N6155A, ISDB- T/TSB Measur ement Applicatio n c. The sensitivity is specified with 0 dB input attenu ation. It represents the noise limitatio ns of the ana- lyzer . It is tested without an input signal. The sensitivity at thi s offset is specified in the default 10.0 kHz RBW , at a center frequency of 7 ...

  • Agilent Technologies N9010A - page 228

    228 Chapter 21 ISDB-T Measurement Application N6155A, ISDB-T/ TSB Measurement Applicati on Out of Band Filtering On or Off Data Equalization On or Off Description Specifications Supplemental Information Modulation Analysis Measurements I/Q Measured Polar Graph Con stellation (subcarriers 0 to 5616 configurable for 8K FFT) MER (dB), EVM (%),Mag Erro ...

  • Agilent Technologies N9010A - page 229

    Chapter 21 229 ISDB-T Measurement Application N6155A, ISDB- T/TSB Measur ement Applicatio n Result Metrics MER (dB), EVM (%), Mag Error (%), Phase Error (deg ), R M S, Peak (Peak Position) MER (dB) and EVM (%) by Layer A, Layer B, Layer C, Data, Pilot, TMCC, AC1 Frequency Error (Hz) Quadrature Error (deg) Amplitude Imbalance (d B) Inband Spectrum R ...

  • Agilent Technologies N9010A - page 230

    230 Chapter 21 ISDB-T Measurement Application N6155A, ISDB-T/ TSB Measurement Applicati on Description Specifications Supplemental Information ISDB-T Modulation Analysis Specification ML a = –20 dBm 20 to 30 °C Segments=13 Mode3 Guard Interval=1/8 Partial Reception=Off Layer A-C Segment=13 Code Rate=3/4 T ime Interleaving I=2 Modulation=64QAM EV ...

  • Agilent Technologies N9010A - page 231

    Chapter 21 231 ISDB-T Measurement Application N6155A, ISDB- T/TSB Measur ement Applicatio n Amplitude Imbalance Range –1 dB to +1 dB a. ML (mixer level) is RF input po wer m inus atten uation b. The accuracy specification applies at the EVM =1%. c. tfa = transmitter frequency x frequency reference accuracy Description Specifications Supplemental ...

  • Agilent Technologies N9010A - page 232

    232 Chapter 21 ISDB-T Measurement Application N6155A, ISDB-T/ TSB Measurement Applicati on ...

  • Agilent Technologies N9010A - page 233

    233 22 DTMB Measur ement Application This chapter contains specificatio ns for the EXA S ignal Analyzer N6156A , DTMB measurement application. Additional Definitions and Requirement s Because digital communications si gnals are noise-like, all measurem ents will have variations. The specifications apply only with adequate averaging to rem ove those ...

  • Agilent Technologies N9010A - page 234

    234 Chapter 22 DTMB Measurement Application N6156A, DTMB Measurement Application N6156A, DTMB Measur ement Application Description Specifications Supplemental Informatio n Channel Power Input signal must not be burst ed 8 MHz Integration BW Minimum power at RF Input –50 dBm (nominal) Absolute Power Accuracy a 20 to 30 °C a. Absolute power accura ...

  • Agilent Technologies N9010A - page 235

    Chapter 22 235 DTMB Measurement Application N6156A, DTMB Measurement Application Description Specifications Supplemental I nformation Power S tatistics CCDF Minimum power at RF Input –50 dBm (nominal) Histogram Resolution 0.01 dB a a. The Complementary Cum ulative Distribution Func tion (CCDF) is a reformattin g of a histogram of the power envelo ...

  • Agilent Technologies N9010A - page 236

    236 Chapter 22 DTMB Measurement Application N6156A, DTMB Measurement Application Description Specifications Supplemental Information Spectrum Emission Mask 7.56 MHz Integration BW RBW = 3.9 kHz 4.2 MHz offset Dynamic Range, rel a tiv e ab a. The dynamic range specification is the r atio of the ch annel power to the power in the of fset specified. T ...

  • Agilent Technologies N9010A - page 237

    Chapter 22 237 DTMB Measurement Application N6156A, DTMB Measurement Application Description Specifications Supplemental Information 16 QAM EVM ML a = –20 dBm 20 to 30 °C a. ML (mixer level) is RF input po wer m inus atten uation Sub-carrier Number: 3780 Code Rate: 0.8 Interleaver T ype: B=52, M=720 Frame Header: PN420 PN Phase Change: T rue EVM ...

  • Agilent Technologies N9010A - page 238

    238 Chapter 22 DTMB Measurement Application N6156A, DTMB Measurement Application Description Specifications Supplemental Information 16 QAM EVM ML a = –20 dBm 20 to 30 °C a. ML (mixer level) is RF input po wer mi nus atten uation Sub-carrier Number: 1 Code Rate: 0.8 Interleaver T ype: B=52, M=720 Frame Header: PN595 PN Phase Change: T rue Insert ...

  • Agilent Technologies N9010A - page 239

    239 23 CMMB Measur ement Application This chapter contains specificatio ns for the EXA S ignal Analyzer N6158A , CMMB m easurement application. Additional Definitions and Requirement s Because digital communications si gnals are noise-like, all measurem ents will have variations. The specifications apply only with adequate averaging to rem ove thos ...

  • Agilent Technologies N9010A - page 240

    240 Chapter 23 CMMB Measurement Application N6158A, CMMB Measurements Application N6158A, CMMB Measur ements Application Description Specifications Supplemental Informatio n Channel Power Input signal must not be burst ed 8 MHz Integration BW Minimum power at RF Input –50 dBm (nominal) Absolute Power Accuracy a 20 to 30 °C a. Absolute power accu ...

  • Agilent Technologies N9010A - page 241

    Chapter 23 241 CMMB Measurement Application N6158A, CMMB Me asur ements Applic ation Description Specifications Supplemental I nformation Power S tatistics CCDF Minimum power at RF Input –50 dBm (nominal) Histogram Resolution 0.01 dB a a. The Complementary Cum ulative Distribution Func tion (CCDF) is a reformattin g of a histogram of the power en ...

  • Agilent Technologies N9010A - page 242

    242 Chapter 23 CMMB Measurement Application N6158A, CMMB Measurements Application Description Specifications Supplemental Information Spectrum Emission Mask 8 MHz Integration BW RBW = 3.9 kHz 4.2 MHz offset Dynamic Range, rel a tiv e ab a. The dynamic range specification is the r atio of the ch annel power to the power in the of fset specified. The ...

  • Agilent Technologies N9010A - page 243

    Chapter 23 243 CMMB Measurement Application N6158A, CMMB Me asur ements Applic ation Description Specifications Supplemental Information Modulation Analysis Settings Device T ype Transmitter or Exciter T rigger FreeRun, External 1, External 2 or Periodic T imer • Ext ernal T rigger is used with 1 PPS input from GPS, (this trigger method is recomm ...

  • Agilent Technologies N9010A - page 244

    244 Chapter 23 CMMB Measurement Application N6158A, CMMB Measurements Application Description Specifications Supplemental Information Modulation Analysis Measurement I/Q Measured Polar Graph Con stellation (-1 538 to 1538 subcarriers) EVM, MER, Mag Error , Phase Error RMS, Peak (Subcarrier position), Freq Error I/Q Error (Quad V iew) MER vs. Subcar ...

  • Agilent Technologies N9010A - page 245

    Chapter 23 245 CMMB Measurement Application N6158A, CMMB Me asur ements Applic ation Channel Impulse Response Spectrum Flatness Amax-Ac (dB) (Limit +0.5) Amin-Ac (dB) (Limit -0.5) Amax: max amplitude valu e Amin: min am pl itude value Ac: center frequency amp value Result Metrics MER (dB), EVM (%), Mag Error (%), Phase Error (deg) RMS, Peak (Peak P ...

  • Agilent Technologies N9010A - page 246

    246 Chapter 23 CMMB Measurement Application N6158A, CMMB Measurements Application EVM (Data EQ OFF) Operating range 0 to 16% Floor 0 .70% Accuracy from 0.7% to 1 .0% from 1.0% to 2 .0% from 2.0% to 1 6.0% ±0.30% ±0.30% ±0.40% MER (Data EQ OFF) Operating range ≥ 16.00 dB Floor 43.00 dB Accuracy (Data EQ OFF) from 39 to 43 dB from 34 to 39 dB fr ...

  • Agilent Technologies N9010A - page 247

    247 24 VXA Measur ement Application This chapter contains specifications fo r the 89601X VXA Measurement Application. Additional Definitions and Requirement s Because digital communications si gnals are noise-like, all measurem ents will have variations. The specifications apply only with adequate averaging to rem ove those variations. Spec ificati ...

  • Agilent Technologies N9010A - page 248

    248 Chapter 24 VXA Measurement Application Basic VSA-Lite Performance (89601X Opti on 205) Basic VSA-Lite Performance (89601X Option 205) Frequency Resolution Bandwidth (RBW) Description Specifications Supplemental Information Range Maximum Frequency Option 503 3.6 GHz Option 507 7 GHz Option 513 13.6 GHz Option 526 26.5 GHz Pr eamp Option P03 3.6 ...

  • Agilent Technologies N9010A - page 249

    Chapter 24 249 VXA Measurement Application Basic VSA-Lite Performance (89601X Option 205) Input Amplitude Accuracy RBW Shape Factor The window choices below allow the user to optimize the RBW shape as needed for best amplitude accuracy , best dynamic range, or best response to transient signal characteristics. Selectivity Passband Flatness Rejectio ...

  • Agilent Technologies N9010A - page 250

    250 Chapter 24 VXA Measurement Application Basic VSA-Lite Performance (89601X Opti on 205) Fr equency Span ≤ 3.6 GHz ≤ 10 MHz ≤ 3.6 GHz > 10 MHz > 3.6 GHz ≤ 10 MHz > 3.6 GHz > 10 MHz Flatness ± 0.40 dB ± 0.45 dB Rms (nominal) 0.02 dB 0.04 dB 0.18 dB (Option B2 5) 0.25 dB 0.28 dB (Option B2 5) Sensitivity − 147 dBm/Hz 10 MHz ...

  • Agilent Technologies N9010A - page 251

    Chapter 24 251 VXA Measurement Application Basic VSA-Lite Performance (89601X Option 205) Dynamic Range Description Specifications Supplemental Informa tion Third-order intermodulation distortion − 84 dBc Tw o − 20 dBfs tones, 10 dBm input range, 400 MHz to 13.6 GHz, tone separation > 5x IF Prefilter BW Noise Density at 1 GHz Input Range Den ...

  • Agilent Technologies N9010A - page 252

    252 Chapter 24 VXA Measurement Application Analog Modulation Analysis (89601 X Op tio n 205) Analog Modulation Analysis (89601X Option 205) Description Specifications Supplemental Information AM Demodulation Carrier ≤− 17 d Bfs Demodulator Bandwidth Same as selected measurement span Modulation Index Accuracy ± 1 % Harmonic Distortion − 55 dB ...

  • Agilent Technologies N9010A - page 253

    Chapter 24 253 VXA Measurement Application Analog Modulatio n Analysis (89601X O ption 205) FM Demo dulation Demodulator Bandwidth Same as selected measurement span Modulation Index Accuracy ± 0.1 % of span, deviation < 2 MHz, modulation rate ≤ 500 kH z Harmonic Distortion Modulation Rate < 50 kHz ≤ 500 kHz Deviation ≤ 200 kHz ≤ 2 MH ...

  • Agilent Technologies N9010A - page 254

    254 Chapter 24 VXA Measurement Application V ector Modulatio n Analy sis (89601X O ption A Y A) V ector Modulation Analysis (89601X Option A Y A) Description Specifications Supplement al Information Accuracy Formats other than FSK, 8/16VSB, 16/32 APSK, and OQPSK; Conditions: Fu ll scale signal, fully contained in the measur ement span, frequency &l ...

  • Agilent Technologies N9010A - page 255

    Chapter 24 255 VXA Measurement Application V ector Modulation Analy sis (89601X O ption A Y A) Residual EVM 16, 32, 64, 128, 256, 512, or 1024 QAM ≤ 1.0 % (SNR ≥ 40 dB) Symbol rate = 6 .9 MHz, α = 0.15, frequency < 3.6 GHz, 8 MHz span, full-scale signal, range ≥− 30 dBm, result length = 800, averages = 10 a. 1.0 % rms EVM and 0.8 deg RM ...

  • Agilent Technologies N9010A - page 256

    256 Chapter 24 VXA Measurement Application V ector Modulatio n Analy sis (89601X O ption A Y A) ...

  • Agilent Technologies N9010A - page 257

    257 25 Option EMC Pr ecompliance Measur ements This chapter contains specifications for the option EMC precompliance measuremen ts. ...

  • Agilent Technologies N9010A - page 258

    258 Chapter 25 Option EMC Precompliance Measurements Requirements for X-Ser ies Requir ements for X-Series • The X-Series must ha ve re v . A.02.00 or later • The X-Series must ha ve option EMC license Conditions Required to Meet Specifications • The X-Series are within their calibration cycle • The X-Series has be en at ope rating temperat ...

  • Agilent Technologies N9010A - page 259

    Chapter 25 259 Option EMC Precompliance Measurements Freque ncy Fr equency Description Specifications Supplemental information Frequency Range CISPR band A, B, C, D, E (9 kHz to 18 GHz) and up to 26 .5 GHz EMI Resolution Bandwidths See T able 25-1 on page 260 and T able 25-2 on page 260 CISPR A vailable when the EMC S tandard is CISPR 200 Hz, 9 kHz ...

  • Agilent Technologies N9010A - page 260

    260 Chapter 25 Option EMC Precompliance Measurements Frequen cy T able 25-1 CISPR Band Settings CISPR Band Freq uency Rang e CISPR RBW Default Data Points Band A 9 – 150 kHz 200 Hz 14 13 Band B 150 kHz – 30 MHz 9 kHz 6637 Band C 30 – 300 MHz 120 kHz 450 3 Band D 300 MHz – 1 GHz 120 kHz 1 1671 Band C/D 30 MHz – 1 GHz 120 kHz 1617 1 Band E ...

  • Agilent Technologies N9010A - page 261

    Chapter 25 261 Option EMC Precompliance Measurements Amplitude Amplitude Description Specifications Supplemental Informat ion EMI A verage Detector Used for CISPR-compliant average measurements and, with 1 MHz RBW , for frequencies above 1 GHz Default A verage T ype All filt ering is done on the linear (voltage) scale even when the display scale is ...

  • Agilent Technologies N9010A - page 262

    262 Chapter 25 Option EMC Precompliance Measurements Amplitude ...

Manufacturer Agilent Technologies Category Stereo System

Documents that we receive from a manufacturer of a Agilent Technologies N9010A can be divided into several groups. They are, among others:
- Agilent Technologies technical drawings
- N9010A manuals
- Agilent Technologies product data sheets
- information booklets
- or energy labels Agilent Technologies N9010A
All of them are important, but the most important information from the point of view of use of the device are in the user manual Agilent Technologies N9010A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Agilent Technologies N9010A, service manual, brief instructions and user manuals Agilent Technologies N9010A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Agilent Technologies N9010A.

Similar manuals

A complete manual for the device Agilent Technologies N9010A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Agilent Technologies N9010A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Agilent Technologies N9010A.

A complete Agilent Technologies manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Agilent Technologies N9010A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Agilent Technologies N9010A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Agilent Technologies N9010A, that we can find in the current document
3. Tips how to use the basic functions of the device Agilent Technologies N9010A - which should help us in our first steps of using Agilent Technologies N9010A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Agilent Technologies N9010A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Agilent Technologies N9010A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Agilent Technologies N9010A?

Use the form below

If you did not solve your problem by using a manual Agilent Technologies N9010A, ask a question using the form below. If a user had a similar problem with Agilent Technologies N9010A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)