English dropdown-ico

Manual Grizzly G7946

28 pages 1.53 mb
Download

Go to site of 28

Summary
  • Grizzly G7946 - page 1

    RADIAL DRILL PRESS MODEL G7945/46 INSTRUCTION MANUAL COPYRIGHT © 2001 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. JUNE, 2001 PRINTED IN CHINA. ...

  • Grizzly G7946 - page 2

    WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemi- cals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks, cement, and other masonr ...

  • Grizzly G7946 - page 3

    G7945/46 Radial Drill Press -1- Table Of Contents PAGE 1. SAFETY SAFETY RULES FOR ALL TOOLS ......................................................................2-3 ADDITIONAL SAFETY INSTRUCTIONS FOR G7945/46 ......................................4 2. CIRCUIT REQUIREMENTS 110V OPERATION ............................................................. ...

  • Grizzly G7946 - page 4

    -2- G7945/46 Radial Drill Press Safety Instructions For Power Tools SECTION 1: SAFETY 5. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance from work area. 6. MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing starter keys. 7. DO NOT FORCE TOOL. It will do the job better and safer at the ...

  • Grizzly G7946 - page 5

    G7945/46 Radial Drill Press -3- 9. USE PROPER EXTENSION CORD . Make sure your extension cord is in good condi- tion. Conductor size should be in accor- dance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your ...

  • Grizzly G7946 - page 6

    -4- G7945/46 Radial Drill Press 1. ALWAYS OPERATE YOUR DRILL PRESS AT SPEEDS that are appropriate for the drill bit size and the material that you are drilling. 2. FEED THE DRILL BIT EVENLY INTO THE WORKPIECE. Back the bit out of deep holes and clear the chips with a brush after you have turned the machine off. 3. MAKE SURE THE DRILL BIT YOU ARE US ...

  • Grizzly G7946 - page 7

    G7945/46 Radial Drill Press -5- 110V Operation SECTION 2: CIRCUIT REQUIREMENTS A 10-amp fuse or circuit breaker should be used when fusing this drill press. Circuits breakers rated any higher may not be adequate to protect the circuit from power surges. If you find it necessary to use an extension cord with the Model G7945/7946, make sure the cord ...

  • Grizzly G7946 - page 8

    -6- G7945/46 Radial Drill Press SECTION 3: INTRODUCTION We are proud to offer the Grizzly Model G7945/46 Radial Drill Press. The Model G7945/46 is part of a growing Grizzly family of fine woodworking machinery. When used according to the guide- lines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Gr ...

  • Grizzly G7946 - page 9

    G7945/46 Radial Drill Press -7- If moving this machine up or down stairs, the machine must be dis- mantled and moved in smaller pieces. Make sure floor and stair structures are capable of supporting the com- bined weight of the machine parts and the people moving them. The Model G7945/46 is shipped from the manu- facturer in a carefully packed cart ...

  • Grizzly G7946 - page 10

    -8- Clean Up The unpainted surfaces are coated with a waxy oil to protect them from corrosion during shipment. Remove this protective coating with a solvent cleaner or citrus-based degreaser such as Grizzly’s G7895 Degreaser. Avoid chlorine-based solvents as they may damage painted surfaces should they come in contact. Always follow the usage ins ...

  • Grizzly G7946 - page 11

    G7945/46 Radial Drill Press -9- SECTION 4: ASSEMBLY Beginning Assembly Most of your Model G7945/46 Radial Drill Press has been assembled at the factory, but some parts must be assembled or installed after deliv- ery. We have organized the assembly process into steps. Please follow along in the order pre- sented here. TOOLS REQUIRED: 11 ⁄ 16 " ...

  • Grizzly G7946 - page 12

    -10- G7945/46 Radial Drill Press The Model G7945 comes with a one piece square table and support as shown in Figure 4 . The Model G7946 comes with a round table and two piece hinged table support. 1. Insert the pinion gear into the hole on the side of the bracket from the inside, starting with the shaft. See Figure 5 . Align the setscrew in the cra ...

  • Grizzly G7946 - page 13

    G7945/46 Radial Drill Press -11- The headstock repre- sents a heavy load. Seek assistance before begin- ning this step. Figure 8 . Lock Handles and gib location. 1. Make sure the locking gib is in the recessed pocket on the inside edge of the headstock opening. See Figure 8. 2. With the help of an assistant, lift the headstock over the top end of t ...

  • Grizzly G7946 - page 14

    -12- G7945/46 Radial Drill Press SECTION 5: ADJUSTMENTS Unplug the drill press before changing speeds. The drill press has 5 speeds ranging from 550 to 3470 R.P.M. There is a speed chart located under the belt guard. Refer to this chart when setting a speed. 1. Loosen the belt tension lock knob on the side of the headstock. See Figure 10 . 2. Pivot ...

  • Grizzly G7946 - page 15

    G7945/46 Radial Drill Press -13- Your radial drill press comes with a depth stop for use when drilling. Follow the instructions below for use. 1. Loosen the depth collar lock knob. See Figure 11 . 2. Secure the wood stock you will be drilling onto the drill press table. 3. With the desired bit installed, lower the spin- dle until the tip of the bit ...

  • Grizzly G7946 - page 16

    -14- G7945/46 Radial Drill Press The Model G7945 table can be adjusted for height and angle. The G7946 adds the adjust- ments of table distance from column and rotation. Follow these instructions to adjust height: 1. Loosen the table support bracket lock han- dle. Turn the table hand crank to lift or lower the table. 2. Remember to lock the support ...

  • Grizzly G7946 - page 17

    G7945/46 Radial Drill Press -15- Head Adjustments Figure 16. Guide pin location. The headstock can be tilted from 45° clockwise to 90° counterclockwise. 1. Loosen the lock handle on the right side of the headstock. 2. Pull out the guide pin located on the left side of the headstock and rotate the pin 90°. See Figure 16 . Tilt the headstock to th ...

  • Grizzly G7946 - page 18

    -16- G7945/46 Radial Drill Press SECTION 6: OPERATIONS Test Run Drill Bit Changes Care must be taken to secure the bit firmly in place. When changing bits, proceed as follows: 1. Disconnect the machine from the power source. 2. Open the chuck wide enough to accept a new bit. 3. Install the bit so the chuck jaws will grab as much of the bit shank as ...

  • Grizzly G7946 - page 19

    G7945/46 Radial Drill Press -17- SECTION 7: MAINTENANCE Lubrication V-Belt Since all bearings are shielded and permanently lubricated, simply leave them alone until they need to be replaced. Do not lubricate them. Inspect regularly for tension and wear. Check pul- leys to ensure that they are properly aligned. See pulley/V-belt sections for proper ...

  • Grizzly G7946 - page 20

    -18- G7945/46 Radial Drill Press The following pages contain general machine data, parts diagrams/lists, a troubleshooting guide and Warranty/Return information for your Model G7945/46 Radial Drill Press. If you need parts or help in assembling your machine, or if you need operational information, we encourage you to call our Service Department. Ou ...

  • Grizzly G7946 - page 21

    G7945/46 Radial Drill Press -19- Design Type ....................................................................................................Bench Model Overall Dimensions: Table ................................................................................................................8 5 ⁄ 8 '' x 9'' Overall Height . ...

  • Grizzly G7946 - page 22

    -20- G7945/46 Radial Drill Press Design Type ......................................................................................................Floor Model Overall Dimensions: Table ........................................................................................................12 3 ⁄ 16 '' Round Overall Height ............... ...

  • Grizzly G7946 - page 23

    43 47 39 37 55 51 50 57 44 48 58 45 59 75 60 32 31 56 46 1 2 3 4 27 34 36 28 28A 28 29 42 41 5 40 33 20 64 65 66 54 38 53 22 23 67 68 16 15 36 71 73 74 69 7 19 11 13 56 49 76 70 17 18 53 21 26 62 25 35 52 72 24 63 2A 11 24 10 77 81 19A 11 83 84 78 79 9 30 8 82 80 4A 5A 84A G7946 ONLY 85 86 ...

  • Grizzly G7946 - page 24

    -22- G7945/46 Radial Drill Press Ref# Part# Description 001 P7945001 BASE 002 P7945002 FLANGE 002A P7946002A W1670 FLANGE 003 PB07 HEX BOLT 5 ⁄ 16 "-18X 3 ⁄ 4 " 004 P7945004 RACK 004A P7945004A LONG RACK 005 P7945005 VERT. COLUMN 005A P7945005A LONG VERT. COLUMN 007 P7945007 TABLE SUPPORT BRACKET 008 P7945008 GEAR 009 P7945009 RETAINE ...

  • Grizzly G7946 - page 25

    G7945/46 Radial Drill Press -23- NOTES ...

  • Grizzly G7946 - page 26

    -24- G7945/46 Radial Drill Press Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole writ ...

  • Grizzly G7946 - page 27

    G7945/46 Radial Drill Press -25- 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press ___Mini Lathe ___8" Table Saw ___10" - 12" Thickness Planer ___8" - 10" Bandsaw ___Scroll Saw ___Disc/Belt Sander ___Spindle/Belt Sander ...

  • Grizzly G7946 - page 28

    FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Place Stamp Here TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name_______________________________ Street_______________________________ City______________State______Zip______ Send a Grizzly Catalog to a friend: ...

Manufacturer Grizzly Category Drill

Documents that we receive from a manufacturer of a Grizzly G7946 can be divided into several groups. They are, among others:
- Grizzly technical drawings
- G7946 manuals
- Grizzly product data sheets
- information booklets
- or energy labels Grizzly G7946
All of them are important, but the most important information from the point of view of use of the device are in the user manual Grizzly G7946.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Grizzly G7946, service manual, brief instructions and user manuals Grizzly G7946. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Grizzly G7946.

Similar manuals

A complete manual for the device Grizzly G7946, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Grizzly G7946 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Grizzly G7946.

A complete Grizzly manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Grizzly G7946 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Grizzly G7946, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Grizzly G7946, that we can find in the current document
3. Tips how to use the basic functions of the device Grizzly G7946 - which should help us in our first steps of using Grizzly G7946
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Grizzly G7946
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Grizzly G7946 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Grizzly G7946?

Use the form below

If you did not solve your problem by using a manual Grizzly G7946, ask a question using the form below. If a user had a similar problem with Grizzly G7946 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)