-
Niles Audio SVL-2 - page 1
SV L- 2 INSTALLATION & OPERA TION GUIDE N I LES ® MODEL SV L - 2 SPEAKER SEL ECTION /VOLUME CONTROL SYSTEM SV L- 2 ...
-
Niles Audio SVL-2 - page 2
Introduction The SVL-2 is a combination speaker selector and volume con- troller. It allows you to connect two pairs of speakers to your stereo receiver or amplifier and adjust the volume of each pair independently. Additionally, you can choose to listen to either pair of speakers, or both pairs simultaneously. You don't have to worry about ov ...
-
Niles Audio SVL-2 - page 3
Features and Benefits The SVL-2 offers a number of improvements over other speaker selector/volume controllers: ● The SVL-2 uses 1 2 position volume controls which are superior to 1 0 position designs. You get a broader range of adjustment — there are 1 0 steps of attenuation instead of 8. Steps 1 1 -6 attenuate -3 dB per step; steps 5-2 are 6 ...
-
Niles Audio SVL-2 - page 4
● Spring-loaded push terminal connectors accommodate up to 1 4 gauge wire or "pins", making the SVL-2 compatible with most "high-definition" speaker cables. ● 1 00% tested, electronically and acoustically, for frequency response, distortion and power handling. ● Only 8 1/2" wide. Match the width of 1 7" component ...
-
Niles Audio SVL-2 - page 5
Installation Considerations SVL-2 Power Handling The SVL-2 is designed for use with a receiver or amplifier hav- ing a maximum power output of 1 00 watts per channel at 8 ohms. Damage caused by the use of a higher-power receiver or amplifier will void the warranty. Consult your Niles dealer, or receiver/amplifier manufacturer, if you are uncertain ...
-
Niles Audio SVL-2 - page 6
The SVL-2 includes impedance correction circuitry which protects your receiver or amplifier from low impedance loads. The circuitry assures that your receiver or amplifier will see a safe operating load, even when two pairs of 4-ohm speakers are playing at the same time. Type of Speaker Wire For most applications, we recommend you use 1 6 or 1 8 ga ...
-
Niles Audio SVL-2 - page 7
near electrical devices, route the speaker wires several feet away from the electrical wiring. Using the SVL-2 with Tube-Type Amplifiers Virtually all tube amplifiers must have a load connected at all times. If the amplifier to be connected to the SVL-2 is a tube amplifier, be sure to always have at least one pair of speakers switched on at all tim ...
-
Niles Audio SVL-2 - page 8
7 S PEAKER S ELECTION /V OLUME C ONTROL S YSTEM SVL-2 SPEAKER SELEC T ION/ VOLUME CONTROL S YS T EM PROTECT ION 12 NI LES SPEAKER 2 SPEAKER 1 LR AMPLIFIER LRLR ++ -- ++ -- Niles Audio Corporat ion, Inc . Miami, Flori da USA NI LES 12 position volume control provides greater attenuation than conventional 10 position des ...
-
Niles Audio SVL-2 - page 9
Installation 1. Select a convenient location for the SVL-2. 2. Run all the necessary wiring to the SVL-2. Label the wires for future reference. See (Figure 2). 8 S PEAKER S ELECTION /V OLUME C ONTROL S YSTEM Figure 2 Wiring Diagram TUNER 94.9 15 SPEAKER 2 SPEAKER 1 LR AMPLIFIER LRLR ++ -- ++ -- Niles Audio Corporat ion, Inc. Miami, Fl or i da USA N ...
-
Niles Audio SVL-2 - page 10
3. Make the connections to the SVL-2. Strip 3 /8" of insulation from the end of each wire. Tightly twist the end of each wire until there are no frayed ends. Insert each wire into the appropriate hole on the spring- loaded connector terminals. Be certain that proper phasing is observed — connect the positive terminals on the SVL-2 to the pos ...
-
Niles Audio SVL-2 - page 11
Operation The are two ways to use the SVL-2. You may play and adjust the volume of either pair of speakers independently, or both pairs simultaneously. If you intend to play both pairs simultaneously, and either pair is less than 8 ohms, you will need to become familiar with the operation of the SVL-2's PROTECTION button. Playing One Pair of S ...
-
Niles Audio SVL-2 - page 12
S PEAKER S ELECTION /V OLUME C ONTROL S YSTEM 6. Using the appropriate volume control on the front of the SVL-2, adjust the volume of the speakers to the desired listen- ing level. 7. You can turn off the speakers by turning the appropriate volume control on the SVL-2 fully counter-clockwise, or by pressing the ON/OFF button. Playing Two Pairs of S ...
-
Niles Audio SVL-2 - page 13
12 3. Set both SVL-2 volume controls to maximum. 4. Locate the ON/OFF buttons on the SVL-2. Set both to the ON position. 5. Turn on the amplifier or receiver and select as source, such as the tuner or CD player. 6. Slowly turn up the amplifier or receiver volume and set it to a comfortable (not maximum) listening level. Be careful not to overdrive ...
-
Niles Audio SVL-2 - page 14
13 S PEAKER S ELECTION /V OLUME C ONTROL S YSTEM Balancing Speaker Volume The volume control on your receiver or amplifier serves as the "master" volume for all speaker pairs connected. The volume level of the speakers may vary from room to room. This is caused by several factors. Two lesser factors are the size of the speaker and its eff ...
-
Niles Audio SVL-2 - page 15
14 S PEAKER S ELECTION /V OLUME C ONTROL S YSTEM SPECIFICA TIONS Audio Power Handling 100 watts/channel continuous music power Frequency Response +/- 1.2 dB from 20 Hz to 20 kHz Mounting Table-top component Wiring Requirements Individual runs of 2-conductor speaker wire. Connectors accommodate wire sizes 14-22 gauge (16 gauge recommended) Overall D ...
-
Niles Audio SVL-2 - page 16
Niles Audio Corporation www.nilesaudio.com 1 233 1 S. W . 1 30 Street Miami, Florida 33 1 86 T el: (305) 238-4373 Fax: (305) 238-0 185 ® NIL E S ® © 1 999 Niles Audio Corporation. All rights reserved. Because Niles constantly strives to improve the quality of its products, Niles reserves the right to change product specifications without notice. ...
Do you have a question concerning Niles Audio SVL-2?
Use the form below
If you did not solve your problem by using a manual Niles Audio SVL-2, ask a question using the form below. If a user had a similar problem with Niles Audio SVL-2 it is likely that he will want to share the way to solve it.