English dropdown-ico

Manual ATEN CS-114A

16 pages 0.68 mb
Download

Go to site of 16

Summary
  • ATEN CS-114A - page 1

    User Manual CS-114A Read this guide thoroughly and follow the installation and operation proce- dures carefully in order to prevent any damage to the units and/or any de- vices that connect to them. This package contains: M 1 Master View CS-114A KVM Switch M 1 Power Adapter M 1 User Manual If anything is damaged or missing, contact your dealer. © ...

  • ATEN CS-114A - page 2

    Overview The Master View CS-114A 4 Port KVM (Keyboard, Video, Mouse), Switch is a control unit that allows acces s to four computer systems from a single PS/2 keyboard, PS/2 mous e, and monitor console in a cost effecti ve manner. There are three convenient methods to acces s the computers: Pushbutton Selection Switches ; Hotkey combinati ons; and ...

  • ATEN CS-114A - page 3

    Hardware Requirements Console M One VGA, SVGA , or Multisync moni tor capable of the highes t resolution that you wi ll be using on any PC i n the installati on M One PS/2 Mouse M One PS/2 Style K eyboard Computers The following equipment must be ins talled on each PC that is to be connected to the system: M A VGA, SVGA or Multisync card. M Either ...

  • ATEN CS-114A - page 4

    Introduction Front View 1. On Line and Selected LEDs: M When an On Line LED is lit, it indi cates that the computer at- tached to the corresponding port i s up and running. M When a Selected LED i s lit, it indi cates that the port it corre- sponds to is the currentl y selected port. Depending on the port ’ s status, the LED may flas h according ...

  • ATEN CS-114A - page 5

    Rear View 1. Power Jack The CS-114A is des igned to be non-powered (external power is not required - its operation power c omes from the computers). In general, the only time that external power is required i s when you daisy chain it, or i f operation becomes errati c because the unit i sn ’ t obtaining enough power from the computer c onnection ...

  • ATEN CS-114A - page 6

    Installation Before You Begin Single Stage Installation The most basic installati on is a Single Stage ins tallation, in whi ch no additional Mas ter View ’ s are dai sy chained down from the first uni t. The Master View CS-114A design also allows additional uni ts to be dai sy chained down to two or three levels. To set up a single stage install ...

  • ATEN CS-114A - page 7

    Two Stage Installation To control even more computers, up to four additi onal Master View CS-114A units can be cas caded from the CPU ports of the First Stage unit. The cascaded Master V iews that connect back to the First S tage unit are considered Second Stage units . As many as 16 computers can be controlled in a c omplete two stage ins tallatio ...

  • ATEN CS-114A - page 8

    Three Stage Installation The procedures for setting up a three stage ins tallation are essenti ally the same as for a two stage installation. With a three stage setup, however, as many as 64 c omputers can be control led in a compl ete installati on. Note: Master View units cannot be cascaded bey ond the third level . - 7 - 2001 - 01 -03 ...

  • ATEN CS-114A - page 9

    Operation Powering Off and Restarting If it becomes necessary to Power Off one of the Master View units , before starting it back up you mus t do the following: 1. Shut down all the computers that are attac hed to it. If the unit is operating under external power, unplug the power adapter c able. Do the same for all the stations and all the compute ...

  • ATEN CS-114A - page 10

    Hotkey Port Selection Hotkey Port Selection allows you to select the acti ve computer directly from the keyboard. The Master View CS-114A prov ides the following Hotkey Port S election features: M Selecting the Acti ve Port M Auto Scan Mode M Last/Next Mode Hotkey Port S election is ac tivated with one of two c ombinations: M The default combinatio ...

  • ATEN CS-114A - page 11

    To access a computer attached to a Second S tage unit, key in a two di git number for the Port ID (press and release eac h number separatel y). The first digit represents the CPU Port number (1 - 4), on the First Stage unit that the Second Stage unit is casc aded down from; the second di git represents the CPU Port number on the S econd Stage uni t ...

  • ATEN CS-114A - page 12

    M Last/Next Mode: Last/Next mode enables you to easily switc h from the currently active computer to the previous or next avai lable computer in the instal lation. There are two methods of invoking Last/Nex t Mode: Basic Mode, and Quick Mode.The choice of mode is made with DIP Switch 4. Set the switc h to Off for Basic Mode; Set the switc h to On f ...

  • ATEN CS-114A - page 13

    Hotkey Summary Table Activity DIP Switch Combination Port Select 3 On [Alt+Ctrl+Shift] Port ID [Enter] 3 Off [LCtrl+RCtrl] Port ID [Enter] Auto Scan 3 On [Alt+Ctrl+Shift] 0 [Enter] 3 Off [LCtrl+RCtrl] 0 [Enter] Basic Last/Next Mode 3 On [Alt+Ctrl+Shift] 9 [Enter] LShift - Last; RShift - Next 3 Off [LCtrl+RCtrl] LShift - Last; RShift - Next Quick La ...

  • ATEN CS-114A - page 14

    DIP Switch Settings Note: The default position for all s ettings is ON. Scan Time - Switch 1 & 2: Seconds Switch1 Switch2 5O n O n 10 Off On 20 On Off 40 Off Off Hotkey Select - Switch 3 / Last/Next Mode Select - Switch 4: See the Hotkey Summary Table on page 12. Specifications Function Specification Power Consumption 800 mW PC Connections Dire ...

  • ATEN CS-114A - page 15

    Troubleshooting Symptom Possible Ca us e Action Keyboard Not Responding 1 Loose c ables. Check all key board cable connecti ons to make sure they are c ompletely seated i n their sockets. Keyboard needs to be reset. Unplug the keyboard from the Console Keyboard Port, then plug it back i n. Master View i s in Auto Scan or Last/Next Mode. Pres s the ...

  • ATEN CS-114A - page 16

    Video Problems Resolution and/or Bandwidth set too high. This unit supports VGA, SVGA, Mult isync, and XGA (interlaced), with resol utions of up to 1920x1440. The maximum bandwidth is 180 MHz. Cable quality not good enough. We strongly recommend that y ou use high quality cables 1 The unit is designed to work with AT and PS/2 k eyboards. Older X T ...

Manufacturer ATEN Category MasterView KVM Switch

Documents that we receive from a manufacturer of a ATEN CS-114A can be divided into several groups. They are, among others:
- ATEN technical drawings
- CS-114A manuals
- ATEN product data sheets
- information booklets
- or energy labels ATEN CS-114A
All of them are important, but the most important information from the point of view of use of the device are in the user manual ATEN CS-114A.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals ATEN CS-114A, service manual, brief instructions and user manuals ATEN CS-114A. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product ATEN CS-114A.

Similar manuals

A complete manual for the device ATEN CS-114A, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use ATEN CS-114A by users. Manuals are usually written by a technical writer, but in a language understandable to all users of ATEN CS-114A.

A complete ATEN manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual ATEN CS-114A - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the ATEN CS-114A, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the ATEN CS-114A, that we can find in the current document
3. Tips how to use the basic functions of the device ATEN CS-114A - which should help us in our first steps of using ATEN CS-114A
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with ATEN CS-114A
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of ATEN CS-114A in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning ATEN CS-114A?

Use the form below

If you did not solve your problem by using a manual ATEN CS-114A, ask a question using the form below. If a user had a similar problem with ATEN CS-114A it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)