English dropdown-ico

Manual Troy-Bilt 469

20 pages 2.75 mb
Download

Go to site of 20

Summary
  • Troy-Bilt 469 - page 1

    21” Self Pr opelled Mulching Mo wer Models 466 & 469 PRINTED IN U .S .A. Oper ator’ s Man ual FORM NO . 769-00955A.f m (10/2004) IMPORT ANT : Read saf ety rules and instructions ca refully before oper ating equipment. Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-co ...

  • Troy-Bilt 469 - page 2

    2 TABLE OF CONTENTS FINDING MODEL NUMBER This Operator’s Manual is an important part of your new lawn mower. It will help y ou assemble, prepare and maintain the unit fo r best perform ance. Please read and unde rstand what it says. Before you start as sembling your new equipment , please loca te the mod el plate on th e equipment and copy th e i ...

  • Troy-Bilt 469 - page 3

    3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES General Oper ation 1. Read this operator’s man ual carefully in its entirety before atte mpting to assemble t his machine. Read, understand, and follow all instructions on the machine and in the manual (s) before operatio n. Be completely familiar with th e controls an d the proper use of this machi ...

  • Troy-Bilt 469 - page 4

    4 your footing, release the blade control ha ndle immediately and th e blade will stop rotating within three seconds. 9. Mow in daylight or good artificial ligh t; walk, not run. 10. Stop th e blade when cr ossing gravel drives, walkways or roads. 11. If th e equipment shoul d start to vibrat e abnormally, stop the engine and check immedi ately for ...

  • Troy-Bilt 469 - page 5

    5 9. Never remove ga s cap or a dd fuel wh ile the eng ine is hot or running. Allow engine to co ol at least two minutes befo re refueling. 10. Never over fill fuel tank. Fill tank to no more than ½ inch below bottom of filler neck to provide space for fuel expansion. 11. Replace gasoline ca p and tighten securely. 12. If gasoline is spilled, wi p ...

  • Troy-Bilt 469 - page 6

    6 SECTION 2: SLOPE GAUGE Use this page as a guide to determine slopes where y ou may not operate safely. 15 o SIGHT AND HOLD THIS LEVEL WITH A VERTICAL TREE A POWER POLE A CORNER OF A BUILDING OR A FENCE POST F O L D ON D O T T E D L I N E, R E P R E SE N T I N G A 1 5 o S L OP E WARNING Do not mow on inclines with a slope in excess of 15 degrees ( ...

  • Troy-Bilt 469 - page 7

    7 SECTION 3: ASSEMBLING YOUR LAWN MOWER Removing Unit From Cart on • Remove stap les, break glue on top flaps, or cut tape at carton en d and peel along top fla p to open. • Remove loose parts included with unit (i. e., operator’s manu al, oil, etc.). • Cut corner s and lay carton down flat. Remove packing material. • Roll or slide unit o ...

  • Troy-Bilt 469 - page 8

    8 Attaching Starter Rope The rope guide is already at tached to the right side of the lower handle of you r mower. See Figure 4 . • With spark p lug wire discon nected and g rounded, hold the blade control hand le against the upper handle, and pu ll the starter rope out of the engine . • Slip the rope thro ugh the rope guide as shown below. Tig ...

  • Troy-Bilt 469 - page 9

    9 SECTION 4: KNOW YOUR LAWN MOWER Read this owner’s manua l and safety rules befo re operating your lawn mower. Com pare the illust rations in Figure 8 with your lawn mower to familiarize yourself with the location of various cont rols and adjustments. Save this ma nual for future refe rence. Figure 8 Starter Rope The starter r ope is attached to ...

  • Troy-Bilt 469 - page 10

    10 SECTION 5: OPERATING YOUR LAWN MOWER Gas & Oil Fill-Up • Check oil level and add oil if necessary. Follow relevant instr uctions in the engine manual fo r this. • Service the engine with gasoline as instruct ed in the engine m anual. Before Starting Mow er • Attach spark plu g wire to spark plug. Make certai n the metal cap on the end ...

  • Troy-Bilt 469 - page 11

    11 SECTION 6: MAINTAINING YOUR LAWN MOWER Cleaning Mower The underside of th e mower deck should be cleaned after each use to preven t any build-up of grass clippings, leaves, dirt , or other debris. If this debris is allowed to accumu late, it will result in rust and corrosion. NOTE: We do not recommend the use of p ressure washers or garden ho se ...

  • Troy-Bilt 469 - page 12

    12 Engine • Follow the engine manu al instructions and recommended schedule for lubricat ing engine components. Blade Care • Periodically inspect the blade adapter and pulley for cracks, especially if yo u strike a fore ign object. Replace when necessary. • Disconnect spa rk plug wire from spark plug. • Turn mower on its side making sure th ...

  • Troy-Bilt 469 - page 13

    13 SECTION 7: SERVICE & ADJUSTMENTS Replacing Drive Belt • Remove two shoulder screws securing th e front drive cover to the mower de ck. See Figure 11. Figure 11 • Press inward o n the sides of the front drive cover and releas e the tab s that secu re the fro nt drive cover to the height adjuster bracket s. Remove drive cover from the mowe ...

  • Troy-Bilt 469 - page 14

    14 Figure 14 • Reassemble t he upper hand le to the lo wer handle. • Place the hairpin clips in the inner holes of th e weld pins and replace th e carriage bolts and wing nuts on the handle bra c kets. Attach the starter r ope as instructed in the Assembly section. Adjusting Cutting Height IMPORT ANT : All wheels must be placed in the same rela ...

  • Troy-Bilt 469 - page 15

    15 SECTION 9: TROUBLE-SHOOTING NOTE: For repairs beyond t he minor adju stments liste d abov e, cont act your local authorized se rvice dealer. Pr oblem P ossible Cause Corrective Action Engine fails to start 1. Blade control handle disenga ged 2. Spark plug wire disconnected 3. Fuel tank empty, or stale fuel 4. Blocke d fuel line 5. Faulty spark p ...

  • Troy-Bilt 469 - page 16

    16 19 75 28 55 53 43 54 52 66 49 28 48 6 74 73 20 72 71 3 11 4 5 2 23 34 31 70 35 29 30 37 56 67 40 24 57 51 61 45 44 42 63 36 38 28 26 32 27 64 39 22 46 8 21 16 7 50 28 25 68 15 17 65 47 14 18 13 1 62 60 59 58 9 10 33 41 69 12 SECTION 10: PARTS LIST FOR MODELS 466 & 469 IMPORTANT: For a proper working machine, use Factory Approved Parts. V-BEL ...

  • Troy-Bilt 469 - page 17

    17 Models 466 & 469 Ref. No P art N o. Description 1. 747-1214 Lower Bail Handle 2. 710-0599 TT Screw 1/4-20 x 0.5 3. 736-0270 Bell Washer.265 x 0.75 4. 17032A Deflector Chute Adapter 5. 732-1014 Torsion Spring 6. 731-04204 Deluxe Bail Cover 7. 747-1161A B lade Control Handl e 8. 749-1092A Uppe r Handle 9. 731-04177 Chute Deflector 10. 687-0205 ...

  • Troy-Bilt 469 - page 18

    18 NOTES ...

  • Troy-Bilt 469 - page 19

    19 NOTES ...

  • Troy-Bilt 469 - page 20

    20 MANUF A CTURER’S LIMITED W ARRANTY FOR: The limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise purch ased and used in the United States, its possessions an d territories. “Troy-Bilt” warrants this product ag ainst defects in mate rial and workmanship for a pe riod of two (2) years commencing on the d ...

Manufacturer Troy-Bilt Category Lawn Mower

Documents that we receive from a manufacturer of a Troy-Bilt 469 can be divided into several groups. They are, among others:
- Troy-Bilt technical drawings
- 469 manuals
- Troy-Bilt product data sheets
- information booklets
- or energy labels Troy-Bilt 469
All of them are important, but the most important information from the point of view of use of the device are in the user manual Troy-Bilt 469.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Troy-Bilt 469, service manual, brief instructions and user manuals Troy-Bilt 469. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Troy-Bilt 469.

Similar manuals

A complete manual for the device Troy-Bilt 469, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Troy-Bilt 469 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Troy-Bilt 469.

A complete Troy-Bilt manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Troy-Bilt 469 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Troy-Bilt 469, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Troy-Bilt 469, that we can find in the current document
3. Tips how to use the basic functions of the device Troy-Bilt 469 - which should help us in our first steps of using Troy-Bilt 469
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Troy-Bilt 469
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Troy-Bilt 469 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Troy-Bilt 469?

Use the form below

If you did not solve your problem by using a manual Troy-Bilt 469, ask a question using the form below. If a user had a similar problem with Troy-Bilt 469 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)