-
Güde TK 2400 ECO - page 1
#55166 TK 2400 ECO © Güde GmbH & Co. KG - Birkichstrasse 6 - D-74549 Wolper tshausen - Deutschland English GB 18 Translation of original operating instructions Circular saw bench ...
-
Güde TK 2400 ECO - page 2
Unit Mobile bench circular saw with a quality aluminium stop and a plastic mitre cut stop, height r eadjustment and mitre adjustmen t b y a hand wheel. Accessories (standard): table ext ension (removable 250 mm) of steel po wder colo ur coated. Dust exhaust, saw disc of sintered m etal, sliding guide rod, emergency switch, stop bar with millimetre ...
-
Güde TK 2400 ECO - page 3
Guarantee The guarantee exclusively applies to material or manufacturing defects. The original proof of purch ase with the purchase date m ust be submitted when lodging a claim in the guaran tee period. The guara ntee does not include any unauthorised use, e.g. appliance overloading, violent use, damage by a third party or foreign item. T he failur ...
-
Güde TK 2400 ECO - page 4
Product Safet y Product compliance with respective EU standards Bans: General ban In combination with another pictogram) Do not touch rotating parts Warning: Warning/caution Beware of hazardous electrical voltage Commands Use goggles Use ear protectors Read operating manual before use Environment Protection Wastes to be disposed of in a professiona ...
-
Güde TK 2400 ECO - page 5
The manufacturer shall not be made liable for damages if general rules and this manual regulations are not observed. Residual Hazards and Protecti ve Action Mechanical Residual Hazards Hazard Description Protective action Residual hazards Cutting, incision Risk of injury caused by rotating parts A contact with rotating band may cause severe injurie ...
-
Güde TK 2400 ECO - page 6
Operator Requiremen ts The operator shall read the instruction manual carefully before using the unit. Qualification No special qualification is required for use of the unit except for d eta iled direction by a professional. Minimum Age Only persons above 16 years of age are allowed to work with the unit. . Exempted from the provision is the use of ...
-
Güde TK 2400 ECO - page 7
+ Fig. 4 Structural group 4 Required structural groups Delivered parts and accessories Structural group 3 Fig. 1 – pos . 8/8 x Fig. 1 – pos. 9/8 x Fig. 1 – pos . 10/8 x Fig. 1 – pos. 3/4 x Fig. 1 – pos . 16/2 x 23 ...
-
Güde TK 2400 ECO - page 8
Fig. 5 Structural group 5 Required structural groups Delivered parts and accessories Fig. 6 Structural group 4 Fig. 1 – pos. 12 Fig. 1 – pos. 14 Fig. 1 – pos. 13 Fig. 1 – pos. 15 Initial Operation Safet y Instruction • Unplug the unit before any adjustment and maintenance . • Caution! Rotating saw disc may hurt hands a nd cut fingers of ...
-
Güde TK 2400 ECO - page 9
• Use only perfect saw discs. I.e. sharpened, without any cracks, fissures, deformations etc. Faulty discs have to be replaced immediately. • Be particular about the arrow on the disc pointi ng on the same dire ction as that on the unit. . • The unit protection devices ma y never be removed or removed from operation in a ny way. • Damaged o ...
-
Güde TK 2400 ECO - page 10
Mitre cut stop Fig. 8 • Put the mitre cut stop (Fig. 2/pos. 14) in the respective clamp on the bench. • Release the mitre cut stop (Fig. 2/pos. 14) with the knurled screw . Turn the stop for the arrow to stop at a required angle • Retighten the knurled screw Caution: Do not move the stop too far in the direction of the saw disc! The distance ...
-
Güde TK 2400 ECO - page 11
Lengthwise Cut ting Fig. 12 • Set the parallel stop (Fig. 2/pos. 3) at the required width in relation to the saw disc. . • Lay the work on the bearing surface are, the flatter/wider side should lay flat on the saw bench. • Guide the wider work with hand, the smaller one with use of a sliding guide rod (Fig. 1/pos. 11). • Caution: Keep a lar ...
-
Güde TK 2400 ECO - page 12
Splitting w edge set-up Fig. 15 • Remove the saw disc cover (Fig. 2/pos. 1). • Remove the removable part of the bench and loosen both the screws on the bench area . • Loosen the screw on the wedge so that the wedge may be shifted – see the type of cut at issue . • Retighten the screw, put the part of the bench in place and fix it . • Pu ...
-
Güde TK 2400 ECO - page 13
Fig. 18 Inspections and Mainte nance Unplug the unit before any works on it. • Use a damp cloth to clean plastic parts. Do not use detergents, solvents and pointed things either. • Clean any dirt from the bench surface with a suitable curing compound spra y. • If the engine braking time is more than 10 s, the fast wearabl e pa rts of the engi ...
-
Güde TK 2400 ECO - page 14
Fig. 22 • Put wrench 13 on the disc spindle . Fig. 23 • Take the belt from the pulley using the screwdriver while turning the disc spindle in the direction of the small pulley. Fig. 24 • Turn until the belt is completely taken off the small pulley . Fig. 25 • Now, take the belt off the big pulley. • Push the worn belt through the pulley a ...
-
Güde TK 2400 ECO - page 15
Fig. 29 • Finished! The saw is in working order again . Inspection and Mainte nance Safety Instructi ons Only a unit maintained and cared for on a regular basis may be a serviceable aid. Insufficient maintenance and care m ay result in emergencies and unforeseen accidents. Inspections and Mainte nance Schedule Time Interval Description Other Deta ...
-
Güde TK 2400 ECO - page 16
EC Declaration of Conformity We herewith declare Güde GmbH & Co. KG Birkichstraße 6, 74549 Wolpertshaus en, Germany That the follo w ing Appliance complies with the appropriate basic safety and health requirements of the EC Directiv e based on its design and type, as brought into circulation by us. In a case of alternation of the machine, not ...
Do you have a question concerning Güde TK 2400 ECO?
Use the form below
If you did not solve your problem by using a manual Güde TK 2400 ECO, ask a question using the form below. If a user had a similar problem with Güde TK 2400 ECO it is likely that he will want to share the way to solve it.