English dropdown-ico

Manual Britax 70 CS

72 pages 5.56 mb
Download

Go to site of 72

Summary
  • Britax 70 CS - page 1

    Boulevard TM 70 C S User Guide IMPORT ANT : Thoroughly read and follow all instructions before installing this child seat. Store this user guide in the pocket behind the cover (See features pages for reference). ...

  • Britax 70 CS - page 2

    ...

  • Britax 70 CS - page 3

    ©2010 Britax Child Safety , Inc. All rights reserved. Printed in USA P435200_R1:09.10 This product and its components are subject to change without notice. Safety Information ....................................................................................... 2 Warnings ........................................................................... ...

  • Britax 70 CS - page 4

    2 Section Title • Use only in a rear -facing position when using it with an infant weighing less than 20 lbs (9.1 kg) OR is less than 1 year of age. • Use only with children who weigh between 5 and 70 lbs (2.3 – 31.8 kg) and whose height is 49 in. (124.5 cm) or less. Use rear - facing for children who weigh between 5 and 40 lbs (2.3 – 18.1 ...

  • Britax 70 CS - page 5

    3 Section Title • This child seat must not be used in the home, in boats, or other non-certified applications. • Based on crash statistics, the National Highway T raffic Safety Administration (NHTSA) recommends that parents select the back seat as the safest location for a properly installed child seat. Please study V ehicle Seating Positions o ...

  • Britax 70 CS - page 6

    4 Impor tant Notes • V erify that the child seat is securely installed and the harness is properly adjusted around the child each time the child seat is used . • Discontinue use of this child seat if it has been in a moderate or severe crash. It is not necessary to replace a car seat after a minor cra sh def ined b y the U .S. National Highway ...

  • Britax 70 CS - page 7

    5 Cer tification This child restraint system conforms to all applicable Federal Motor V ehicle Safety Standards. This Restraint is Certified For Use in Motor V ehicles and Aircraft. Registration Child restraints could be recalled for safety reasons. Y ou must register this restraint to be reached in a recall. Send your name, address, e-mail address ...

  • Britax 70 CS - page 8

    6 WARNING! REAR-F ACING use of this child seat is ONL Y for children who meet ALL of the requirements below . If the child cannot be secured within these requirements because they are too small, use of the infant positioning insert or selection of a different child seat (such as an infant car seat) may be required. If the child cannot be secured wi ...

  • Britax 70 CS - page 9

    7 WARNING! FORWARD-FACING use of this child seat is ONL Y for children who meet ALL of the requirements below . If the child cannot be secured within these requirements because they are too large, another type of child seat (such as a booster) may be required. If the child cannot be secured within these requirements because the child is too small, ...

  • Britax 70 CS - page 10

    8 Compatible V ehicle Seat Belts NOTE: The information in this section only applies to installation with vehicle seat belts. V ehicle seats and seat belts differ from vehicle to vehicle. Refer to your vehicle owner’s manual for specific information about your vehicle seat belts and their use with child seats. Lap-Shoulder (3-Point) Belt 1. ALR (A ...

  • Britax 70 CS - page 11

    9 2. ELR (Emergency Locking Retractor) with Locking Latch Plate a Has a latch plate that locks the vehicle belt. * This type of latch plate locks the vehicle belt when the vehicle belt and latch plate lie flat. When using this type of vehicle belt with a child seat, ensure the latch plat and vehicle belt lie flat against the child seat or the vehic ...

  • Britax 70 CS - page 12

    10 4. ELR (Emergency Locking Retractor) with a Sliding Latch Plate a Has a latch plate that freely slides along the vehicle seat belt webbing. b Has a retractor that locks only in an emergency situation such as sudden stop or crash. IMPORT ANT : This belt type requires the use of the lock -offs built into the seat for rear - and forward-facing inst ...

  • Britax 70 CS - page 13

    11 c Tightens by feeding the belt webbing back into the retractor . 6. Locking Latch Plate a Has a latch plate that prevents the webbing from becoming loose. b Tightens by pulling on the belt webbing. V ehicle Compatibility Adjuster Latch plate ...

  • Britax 70 CS - page 14

    12 Incompatible Vehicle Seat Belts WARNING! The following types of vehicle seat belts are NOT compatible with this child seat. If any of the belt types listed below are in the chosen seating position, choose another vehicle seating position or check your vehicle owner’s manual for information on installing a car seat in your vehicle. 1 Lap-should ...

  • Britax 70 CS - page 15

    13 WARNING! DO NOT place child seat rear -facing in the front seat of a vehicle with a passenger air bag unless deactivated. DEA TH or SERIOUS INJURY can occur . See your vehicle owner’s manual for child seat installation instructions. The back seat is the safest place for children 12 and under . Some vehicles have no seating positions which are ...

  • Britax 70 CS - page 16

    14 1 Cover 2 Harness Height Adjuster 3 Head Restraint 4 Comfort Pads 5 Infant Body Pillow 6 Harness Holder 7 Lower Connector Bar 8 Lower Connector Strap (LA TCH component) 9 Lower Connector Adjuster Release Button (LA TCH component) 10 Lower Connector Adjuster (LA TCH component) 11 Lower Connector Release Button (LA TCH component) 12 Lower Connecto ...

  • Britax 70 CS - page 17

    15 17 Belly Pad 18 Harness Adjuster Lever (under cover) 19 Click & Safe™ Snug Harness Indicator (under cover) 20 Harness Adjuster Strap 21 Recline Adjustment Handle 22 Shell 23 Serial Number & Manufactured Date Label 24 Harness Slots 25 Forward-Facing Belt Slot 26 Forward-Facing Lock -Offs (Red – under cover on front of shell) 27 Rear-F ...

  • Britax 70 CS - page 18

    16 Click & Safe™ Snug Harness Indicator 2 Check for proper harness height. I mpo R t AN t: See pages 55 – 57 for detailed instructions on securing your child. The Click & Safe is an audible indicator to help determine when the child seat harness is within range of appropriate snugness. The Click & Safe is a secondary feature. P aren ...

  • Britax 70 CS - page 19

    17 Checklist 9 Check that the harness is buckled and secure. 9 Check that the harness is snug and you can not pinch excess. 3 Remove slack in the harness from around child’s upper thighs. 4 Remove slack in the harness between the HUGS™ chest pads and buckle. 5 Pull the harness adjuster strap up until a click is heard. The Click & Safe™ in ...

  • Britax 70 CS - page 20

    18 Harness Height Adjustment 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Squeeze the harness height adjuster , slide the harness into the desired position and release. * Ensure the harness has locked into position. NOTE: In rear -facing mode, always position the harness straps at or below your child’s ...

  • Britax 70 CS - page 21

    19 Adjusting Buckle P osition 1 Unbuckle the harness. Remove the belly pad and push the buckle through the cover . 2 T urn the buckle webbing and slide it between buckle positions. 3 Slide the buckle retainer into the buckle slot, and ensure the red release button faces out. I mpo R t AN t : • AL WAYS position the buckle in the inner slot for rea ...

  • Britax 70 CS - page 22

    20 F astening the Buckle Insert one tongue at a time into the buckle. NOTE: Proper connection is confirmed with a click after inserting each buckle tongue. Releasing the Buckle Press the release button and pull the tongues from the buckle. NOTE: Periodically clean the buckle to ensure proper operation. See Page 64. Using the Chest Clip 1 Open the c ...

  • Britax 70 CS - page 23

    21 Using the Lock- Offs IMPORT ANT : Both parts of the lock -off must be opened to secure a vehicle belt. 1 Open the locking tab 2 Open the clamp T o Open: 1 Close the clamp over the vehicle belt 2 Slide your palm or thumb along the locking tab until a click is heard T o Close: Infant Body Pillow The infant body pillow is designed to provide better ...

  • Britax 70 CS - page 24

    22 Recline P ositions This child seat has 3 positions. T o adjust, pull the recline handle then rotate the child seat shell into the desired position. Release the recline handle, then verify the child seat has locked into position. NOTE: Set the recline position BEFORE installing. Rear-F acing When installed in the rear-facing position, the child s ...

  • Britax 70 CS - page 25

    23 Forward-F acing IMPORT ANT : In forward-facing installations, it is important that the base of the child seat rests completely flat on the vehicle seat. As illustrated below , it is permissible to allow up to 20% or 3 inches (7.6 cm) of the base to hang over the edge of the vehicle seat. Some vehicle seats do not allow enough of the child seat b ...

  • Britax 70 CS - page 26

    24 Using Lower Anchors and T ethers for Children (L A TCH) Lower Anchors and T ethers for Children or LA TCH, is a system available on this child seat that offers an alternative to vehicle seat belt installation methods. See pages 14 and 15 for LA TCH components on this child seat. The figure above shows typical locations for lower anchors and teth ...

  • Britax 70 CS - page 27

    25 Using the Lower Connectors Where to find the Lower Connectors The lower connectors are located in the back of the base of the child seat. Store the connectors in the slots when not in use. T o remove the lower connector from the storage slot or lower anchor: 1 Press and hold the red release button. 2 Pull the lower connector from the storage slo ...

  • Britax 70 CS - page 28

    26 Using the V ersa- T ether ® T ether anchor locations vary from vehicle to vehicle. Check your vehicle owner’s manual and look for the tether anchor symbol shown in the diagram to help identify where the top tether anchor points are located in your vehicle. Britax recommends that the tether be used at all times when installing the child seat. ...

  • Britax 70 CS - page 29

    27 Rear-F acing T ether Connector Strap Because every vehicle model is different, a location to anchor the tether for rear -facing installations may vary . Use the rear -facing tether connector strap to assist in creating an anchor point. 1 Find a fixed location in the vehicle that is bolted to the floor . * If you cannot find a location to create ...

  • Britax 70 CS - page 30

    28 IMPORT ANT : The Versa- T ether ® carry clip is only for use when you wish to carry the child seat between locations. Do not install the child seat with the V ersa- T ether attached to the carry clip. Secure the excess Versa- T ether webbing in the elastic strap during use. Store the Versa- T ether in the storage pouch when not in use. Always e ...

  • Britax 70 CS - page 31

    29 The V ersa- T ether can indicate when the child seat has been in a moderate or severe crash (see page 4) and replacement of the child seat is necessary . Figure 1 shows a tether acceptable for continued use (provided the child seat has not been involved in a crash). The colored stitching will be intact but not visible from the back of the seat. ...

  • Britax 70 CS - page 32

    30 Before Y ou Begin: • Check that your vehicle has lower anchors. * Refer to your vehicle owner’s manual or contact the vehicle manufacturer for the maximum weight rating for their lower anchors. Use vehicle belt (not lower connectors) for installations with children who weigh more than the vehicle lower anchor limit. Unless specified otherwis ...

  • Britax 70 CS - page 33

    31 Install with LA TCH as shown above. Rear-F acing Installation I mpo R t AN t: The buckle should be in the inner slot for rear -facing installation . ...

  • Britax 70 CS - page 34

    32 1 Firmly press the lower connectors onto the adjacent lower anchors. • A click confirms attachment. • Verify that the lower connector strap is not twisted. TIP: Y ou may need to turn the front of the child seat toward you for easier access to the lower anchors. NOTE: If a click is not heard when connecting either lower connector , the lower ...

  • Britax 70 CS - page 35

    33 Checklist 9 Check that all connections are secure. 9 Check that the lower connector straps are not twisted. 9 Check that the child seat cannot be moved front to back or side to side more than 1 in. (2.5 cm) at the belt path. If the child seat is not secure, repeat installation or use a different seating location. 9 Check that the back angle of t ...

  • Britax 70 CS - page 36

    34 Before Y ou Begin: • Check that your vehicle belt is compatible for use with child seats. See pages 8 – 13 for more information. * If your vehicle seat belt system includes a locking feature, use of the lock -offs is not required as long as the vehicle seat belt system is locked. Check your vehicle owner’s manual to determine how to lock y ...

  • Britax 70 CS - page 37

    35 Install with lap-shoulder belt as shown above. I mpo R t AN t: • The harness buckle strap should lie toward the back of the child seat during installation. • The buckle should be in the inner slot for rear -facing installation. Rear-F acing Installation ...

  • Britax 70 CS - page 38

    36 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Remove the body pillow , unbuckle the harness, and remove the belly pad. 3 Pull the head restraint cover up, then pull the seat cover forward while pulling the buckle through to access the rear -facing belt path. IMPORT ANT : Ensure buckle is in inner slot a ...

  • Britax 70 CS - page 39

    37 Checklist 9 Check that the vehicle belt is securely fastened. 9 Check that the child seat cannot be moved front to back or side to side more than 1 in. (2.5 cm) at the belt path. If the child seat is not secure, repeat installation or use a different seating location. 9 Check that the back angle of the child seat is 30º – 45º from vertical ( ...

  • Britax 70 CS - page 40

    38 Lap Belt Installation Before Y ou Begin: • Check that your vehicle belt is compatible for use with child seats. See pages 8 – 13 for more information. • This child seat must be reclined to position 3 and placed rear-facing on the vehicle seat. * When properly installed in the rear -facing position, the back angle of the child seat should b ...

  • Britax 70 CS - page 41

    39 Install with lap belt as shown above. I mpo R t AN t: • The harness buckle strap should lie toward the back of the child seat during installation. • DO NOT use lock -offs for lap belt installations. • The buckle should be in the inner slot for rear -facing installation. Rear-F acing Installation ...

  • Britax 70 CS - page 42

    40 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Remove the body pillow , unbuckle the harness, and remove the belly pad. 3 Pull the head restraint cover up, then pull the seat cover forward while pulling the buckle through to access the rear -facing belt path. 4 Route the vehicle seat belt through the rea ...

  • Britax 70 CS - page 43

    41 Checklist 9 Check that the vehicle belt is securely fastened. 9 Check that the child seat cannot be moved front to back or side to side more than 1 in. (2.5 cm) at the belt path. If the child seat is not secure, repeat installation or use a different seating location. 9 Check that the back angle of the child seat is 30º – 45º from vertical ( ...

  • Britax 70 CS - page 44

    42 Before Y ou Begin: • Check that your vehicle has lower anchors. * Refer to your vehicle owner’s manual or contact the vehicle manufacturer for the maximum weight rating for their lower anchors. Use vehicle belt (not lower connectors) for installations with children who weigh more than the vehicle lower anchor limit. Unless specified otherwis ...

  • Britax 70 CS - page 45

    43 Install with LA TCH as shown above. WARNING! • Y our child seat may not perform as intended if the base of the child seat is not flat on the vehicle seat. • This child seat must not be used forward-facing for children less than one year of age OR who weigh less than 20 lbs (9.1 kg). • Some vehicle head restraints may obstruct the harness a ...

  • Britax 70 CS - page 46

    44 1 Firmly press the lower connectors onto the adjacent lower anchors. • A click confirms attachment. • Verify that the lower connector strap is not twisted. TIP: Y ou may need to turn the back of the child seat toward you for easier access to the vehicle lower anchors. NOTE: If a click is not heard when connecting either lower connector , the ...

  • Britax 70 CS - page 47

    45 Checklist 9 Check that all connections are secure. 9 Check that the lower connector straps are not twisted. 9 Check that no more than 20% or 3 inches (7.6 cm) of the base hangs over the edge of the vehicle seat. 9 Check that the child seat cannot be moved front to back or side to side more than 1 in. (2.5 cm) at the belt path. If the child seat ...

  • Britax 70 CS - page 48

    46 Before Y ou Begin: • Check that your vehicle belt is compatible for use with child seats. See pages 8 – 13 for more information. * If your vehicle seat belt system includes a locking feature, use of the lock -offs is not required as long as the vehicle seat belt system is locked. Check your vehicle owner’s manual to determine how to lock y ...

  • Britax 70 CS - page 49

    47 Install with lap-shoulder belt as shown above. WARNING! • Y our child seat may not perform as intended if the base of the child seat is not flat on the vehicle seat. • This child seat must not be used forward-facing for children less than one year of age OR who weigh less than 20 lbs (9.1 kg). • Some vehicle head restraints may obstruct th ...

  • Britax 70 CS - page 50

    48 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Remove the body pillow and unbuckle the harness. 3 Pull the head restraint cover up, then pull the seat cover forward to access the forward-facing belt path. 4 Open the red lock-off closest to where the vehicle belt will be buckled. a Open the locking tab b ...

  • Britax 70 CS - page 51

    49 Checklist 9 Check that the vehicle belt is securely fastened. 9 Check that no more than 20% or 3 inches (7.6 cm) of the base hangs over the edge of the vehicle seat. 9 Check that the child seat cannot be moved front to back or side to side more than 1 in. (2.5 cm) at the belt path. If the child seat is not secure, repeat installation or use a di ...

  • Britax 70 CS - page 52

    50 Lap Belt Installation Before Y ou Begin: • Check that your vehicle belt is compatible for use with child seats. See pages 8 – 13 for more information. • Remove the Versa- T ether from the pouch and place it up and over the child seat back. * Britax recommends that the V ersa-T ether is used at all times. Using the tether will improve the s ...

  • Britax 70 CS - page 53

    51 Install with lap belt as shown above. WARNING! • DO NOT use lock -offs for lap belt only installations. • Y our child seat may not perform as intended if the base of the child seat is not flat on the vehicle seat. • This child seat must not be used forward-facing for children less than one year of age OR who weigh less than 20 lbs (9.1 kg) ...

  • Britax 70 CS - page 54

    52 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Remove the body pillow and unbuckle the harness. 3 Pull the head restraint cover up, then pull the seat cover forward to access the forward-facing belt path. 5 Push the child seat down while pulling the vehicle belt to remove all slack (see pages 10 – 11). ...

  • Britax 70 CS - page 55

    53 Checklist 9 Check that the vehicle belt is securely fastened. 9 Check that no more than 20% or 3 inches (7.6 cm) of the base hangs over the edge of the vehicle seat. 9 Check that the child seat cannot be moved front to back or side to side more than 1 in. (2.5 cm) at the belt path. If the child seat is not secure, repeat installation or use a di ...

  • Britax 70 CS - page 56

    54 This child seat is certified for aircraft use. Most airlines in the U .S. and Canada will allow the use of a child seat as long as it is labeled as an approved child seat for use in aircraft and fits properly on the aircraft seat. Contact the airline about their policy prior to traveling. The F AA recommends that a child weighing up to 40 lbs (1 ...

  • Britax 70 CS - page 57

    55 Securing Y our Child WARNING! • Adjust the belts provided with this child seat so they fit snugly around your child. A snug strap should not allow any slack. It lies in a relatively straight line without sagging. It does not press on the child’s flesh or push the child’s body into an unnatural position. • Adjust the harness to fit the cl ...

  • Britax 70 CS - page 58

    56 1 Loosen the harness. a Lift harness adjuster lever b Pull both harness straps forward 2 Open the chest clip. a Press tabs b Pull apart 3 Release the buckle and attach the harness straps to the harness holders. 4 Place the child in the child seat. * Ensure the child is positioned upright in the child seat and not slouching. Their bottom must tou ...

  • Britax 70 CS - page 59

    57 6 Fasten the harness buckle. * Proper connection is confirmed with a click after inserting each buckle tongue. 7 Pull the excess slack up to the child’s shoulder area while moving the HUGS ™ chest pads down toward the buckle. 8 Pull the harness adjuster strap up to tighten the harness. The Click & Safe™ indicator will click when the ha ...

  • Britax 70 CS - page 60

    58 Cover R emoval WARNING! • Never remove the buckle tongues from the harness. They cannot be reattached after removal. If reassembled incorrectly , the child seat may not perform as intended. • DO NOT remove the HUGS ™ chest pads from the harness straps. 1 Loosen the harness. a Lift release lever b Pull both harness straps forward 2 Open the ...

  • Britax 70 CS - page 61

    59 6 Raise the harness to the highest position and detach the hook and loop fasteners on the head restraint cover from around the harness. 7 Detach the hook and loop fasteners on the head restraint cover from around the head restraint. 8 Detach the elastic straps from the tabs behind the harness adjustment handle. 9 Remove the head restraint cover ...

  • Britax 70 CS - page 62

    60 13 Pull the buckle through the slot in the cover . Care and Maintenance 14 Remove the cover from the child seat shell. 1 4 ...

  • Britax 70 CS - page 63

    61 Care and Maintenance Cleaning the Cover • HAND WASH the cover using cold water and mild soap. • LINE DRY to prevent the cover from shrinking. • DO NOT : * Bleach * Machine wash * Machine dry * Iron Cleaning the Harness • SPONGE CLEAN the harness using warm water and mild soap. • TOWEL DRY • DO NOT : * Disassemble the harness * Bleach ...

  • Britax 70 CS - page 64

    62 Cover Replacement 1 Fit the child seat cover around the child seat shell. 3 Attach the plastic hooks to the bottom edge of the child seat. Care and Maintenance 2 Attach the plastic hooks on the cover to the back of the child seat shell. 4 Pull the buckle through the slot in the cover . * Ensure that the buckle is through the correct cover slot f ...

  • Britax 70 CS - page 65

    63 5 Fit the head restraint cover around the harness adjustment handle and attach the elastic straps to the tabs behind the harness adjustment handle. 6 Attach the hook and loop fasteners on the head restraint cover around the head restraint. 7 Attach the hook and loop fasteners on the head restraint cover around the harness. Care and Maintenance 8 ...

  • Britax 70 CS - page 66

    64 Care and Maintenance Cleaning the Buckle If your child eats and drinks while in the child seat, you will need to check the buckle periodically and rinse out any accumulated debris. Remove the Buckle 2 T urn the buckle webbing and slide it between buckle positions. 1 Unbuckle the harness. Remove the belly pad and pull the buckle through the cover ...

  • Britax 70 CS - page 67

    65 Care and Maintenance 3 Guide the buckle retainer up through the slot in the child seat shell to remove. T o Clean: • THOROUGHL Y RINSE the buckle using warm water . • TEST THE BUCKLE by fastening and unfastening until a click is heard after inserting each buckle tongue. If clicks are not heard, repeat the cleaning procedure. • TOWEL DRY ? ...

  • Britax 70 CS - page 68

    66 Care and Maintenance Re-thread the Buckle 1 Guide the buckle retainer down through the slot in the child seat shell. 2 Slide the buckle webbing into the slot between buckle positions. 3 Select the appropriate slot for the size of your child and turn the buckle webbing and slide it into the chosen slot. 4 Ensure that the buckle strap is not twist ...

  • Britax 70 CS - page 69

    67 Tips and T roubleshooting T roubleshooting Problem: The harness cannot be adjusted to its full height. Possible Solution: Check the seating position where the child seat is installed. The vehicle head restraint may obstruct the path of the child seat harness height adjuster . Remove or raise the vehicle head restraint and try adjusting the harne ...

  • Britax 70 CS - page 70

    68 This child seat was manufactured by Britax Child Safety , Inc. Britax ® warrants this product to the original retail purchaser as follows: LIMITED ONE- YEAR WARRANTY This product is warranted against defective materials or work man ship for one year from the date of original purchase. Proof of purchase is required. Y our exclusive remedy for th ...

  • Britax 70 CS - page 71

    69 ...

  • Britax 70 CS - page 72

    Britax Child Safety , Inc. 13501 South Ridge Drive Charlotte, NC 28273 USA A Britax Childcare Group Limited company T el. : 1-888-427-4829 www .Britax.com ...

Manufacturer Britax Category Car Seat

Documents that we receive from a manufacturer of a Britax 70 CS can be divided into several groups. They are, among others:
- Britax technical drawings
- 70 CS manuals
- Britax product data sheets
- information booklets
- or energy labels Britax 70 CS
All of them are important, but the most important information from the point of view of use of the device are in the user manual Britax 70 CS.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Britax 70 CS, service manual, brief instructions and user manuals Britax 70 CS. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Britax 70 CS.

Similar manuals

A complete manual for the device Britax 70 CS, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Britax 70 CS by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Britax 70 CS.

A complete Britax manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Britax 70 CS - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Britax 70 CS, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Britax 70 CS, that we can find in the current document
3. Tips how to use the basic functions of the device Britax 70 CS - which should help us in our first steps of using Britax 70 CS
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Britax 70 CS
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Britax 70 CS in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Britax 70 CS?

Use the form below

If you did not solve your problem by using a manual Britax 70 CS, ask a question using the form below. If a user had a similar problem with Britax 70 CS it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)