English dropdown-ico

Manual Summit HL-630 OPC

46 pages 2.7 mb
Download

Go to site of 46

Summary
  • Summit HL-630 OPC - page 1

    SU MM IT Technologies Cartridge/Machine Reset Guide Version 16 Now with HP & Lexmark co mmon chip error codes! By Mike Josiah Welcome to the 16 th version of our Reset Guide! This guide continues to expand (sometimes on a daily basis), and it will c ontinue to expand for the for-seeable future. Although most machines these days are chip based, ...

  • Summit HL-630 OPC - page 2

    2 Brother HL-1040 OPC Brother Cartridge Part #DR-300 OEM Stated Yield: 20,000 New drum cartridges com e with a clear “Starter Sheet” installed inside th e cartridge. When the cartridge is installed and th e cover closed, the printer will eject the sheet and at the same tim e, reset the drum counter. This sheet is also present in the DR- 200 car ...

  • Summit HL-630 OPC - page 3

    3 Brother HL-3260N OPC Brother Cartridge Part #DR-1200 OEM Stated Yield: 60,000 The HL-3260 is Brothers fi rst high speed printer. The drum cartridge comes with three RED sheets and two pieces of tape installed on the cartridg e. There is a possibility that there is developer inside the drum cartridge. Removal of these is what seems to reset the co ...

  • Summit HL-630 OPC - page 4

    4 Brother HL-7050 Toner Brother Cartridge Part #TN-700 (TN-5500) OEM Stated Yield: 12,000 Located inside the cartridge handle is a small fuse that looks similar to a resist or. It is a 1/8A, 250V fast acting fuse, and must be replaced each cycle. Brother HL-7050 OPC Brother Cartridge Part #DR-700 (DR-5500) OEM Stated Yield: 40,000 The HL-7050 is a ...

  • Summit HL-630 OPC - page 5

    5 Canon NP-6016/C-160 OPC Canon Cartridge Part # F43-4921-700 (NPG-9) OEM Stated Yield: 40,000 The drum unit for these cartridges is rated for 40,000 pages. The machine will show “Replace Drum” at 40,000 pages or when the waste toner section is full. These cartridges have a reset chip built into the connector. This connector must be reset befor ...

  • Summit HL-630 OPC - page 6

    6 for 5% pages, so it is very possible that you have an empty cartridge with a green wheel showing, or a half full cartridge with a red wheel showing. It all depends on how much toner is used per page. To reset the counter, grasp the color wheel in your right hand, the gear assembly in your left. While bending the wheel down, turn the wheel away fr ...

  • Summit HL-630 OPC - page 7

    7 Goldstar GL-660 (Xerox W.C. Pro 610) 6R00833 Toner, 13R00532 OPC Toner: 5,000 pages, OPC: 10,000 Pages Toner With the Machine on, open the access cover. Press “MENU”, Press “6”, Press “3” Press “CLEAR”, Press “ENTER” OPC With the Machine on, open the access cover. Press “MENU”, Press “6”, Press “4” Press “CLEAR? ...

  • Summit HL-630 OPC - page 8

    8 HP Color LaserJet 2600 HP Black # Q6000A, Cyan Q6001A, Magenta Q6003A, Yellow Q6002A OEM Stated Toner Yield: 2500 Black, 2000 Color These cartridges have what HP now calls “Smart Print Technology Chips”. These are the latest in HP chips, they are very small, and contain all new code. As with most HP chips, these chips monitor toner usage. The ...

  • Summit HL-630 OPC - page 9

    9 HP Color LaserJet 3700 HP Black # Q2670A, Cyan Q2681A, Yellow Q2682A, Magenta Q2683A OEM Stated Toner Yield: 6000 Black, 6000 Color These cartridges have what HP now calls “Smart Chips” Similar to other HP chips, these chips monitor toner usage, Internet supplies ordering, and a new feature, remote troubleshooting. Unlike the 4100, the chips ...

  • Summit HL-630 OPC - page 10

    10 HP Color LaserJet 4500 Transfer Belt HP OPC Part # C4196A OEM Stated Yield: 100,000 Black, 25,000 Color Press the menu button until “RESET MENU” is displayed. Press the “ITE M” button until “NEW TRANSFER KIT, SELECT IF DONE” is displayed. Press the “SELECT” button. Press the “ITEM” button until the “INFORMATION” menu is d ...

  • Summit HL-630 OPC - page 11

    11 HP Color LaserJet 5500/5550 HP Black # C9730A, Cyan C9731A, Magenta C9733A, Yellow C9732A OEM Stated Yield: 13,000 Black, 12,000 Color These cartridges have what HP now calls “Smart Chips. Similar to the HP-4100, these chips monitor toner usage, Internet su pplies ordering, and a new feature, remote troubles hooting. These cartridges are “al ...

  • Summit HL-630 OPC - page 12

    12 HP LaserJet 1300 HP Part # Q2613A/X OEM Stated Yield: 2,500/4,000 The HP-1300 uses the second generation black toner cartridge ARD’s. These chips (ARD’s) only monitor toner usage not page counts. Each chip also has its own serial number wh ich in effect gives the cartridge a serial number. After the OEM toner has been used up, the “toner l ...

  • Summit HL-630 OPC - page 13

    13 set to YES on the cartridge chip. Even after the cartridge is refilled, the printer display will still show “Toner Low” for the supplies status section of the menu. Since these machines do not have a display, only the supplies status page will show “Non HP Toner cartridge”. If the chip is removed, the toner low sensors will be disab led, ...

  • Summit HL-630 OPC - page 14

    14 the menu. The main display will then show “Non HP Toner cartridge”. If the ch ip is removed, the toner low sensors will be disabled, and will not work again until a new HP cartridge is installed. Replacem ent chips are available. Specific 4250 Error Codes : “10.32.00” If it is displayed, it m eans the printer senses this is not an HP ori ...

  • Summit HL-630 OPC - page 15

    15 HP LaserJet 9000 HP Part # C4583X OEM Stated Yield: 30,000 Like the HP-4100, the 9000 cartridge also uses a chip. The chip in the 9000 is the same as the 4100 in that they only monitor usage not page counts. Each chip also has its own serial number which in effect gives the cartridge a seri al num ber. After the OEM toner has been used up, the ? ...

  • Summit HL-630 OPC - page 16

    16 Kyocera F-3010 OPC Kyocera OPC Part # DK-2 OEM Stated Yield: 10,000 There is a small black fuse located on the board inside the cartridge. This fuse must be replaced each cycle by un-soldering the ol d and soldering in the new. This fuse is a special 250mA one that should be purchased from your supp lier. The same fuse is used in the F-1000 OPC ...

  • Summit HL-630 OPC - page 17

    17 Lexmark 4023 (Optra W820/Xerox 4525) Lexmark Cartridge Part # 12B0090 OEM Stated Yield: 5840/5740: 10,000. 5845/5745: 25,000 The “Return” cartridges have an ARD on a small board located inside th e right end cap of the cartridge. Unlike other Lexmark chips, the board for these cartridges has two contact pads where the machine makes direct co ...

  • Summit HL-630 OPC - page 18

    18 E-120 Drum cartridge: With the printer turned on, open the front door. Press and hold the CANCEL button until all the lights be gin to cycle. Close the front door. Press the continue button to resume printing. Lexmark E220 Lexmark Cartridge Part 12S0300 (Return Program), 12S0400 (Standard) OEM Stated Yield: 2,500 This system uses a separate tone ...

  • Summit HL-630 OPC - page 19

    19 Lexmark E238 Lexmark Toner Cartridge Part #’s 23800SW, (Return Program), 23820SW (Standard) OEM Toner Stated Yield: 2,000 OEM Drum cartridge 12A8302, Stated drum yield: 30,000 Toner cartridges : The “Return” toner cartridges have an ARD on a small board located inside the right end cap of the cartri dge. Like other cartridges in this serie ...

  • Summit HL-630 OPC - page 20

    20 Lexmark E321/323 Lexmark Cartridge Part 12A7400/12A7405 (Prebate), 12A7305 (Non Prebate)) OEM Stated Yield: 3,000 (7400), 6000 (7305) The “Return” cartridges have an ARD on a small board located inside th e right end cap of the cartridge. Like other cartri dges in this series, the board for these cartridge s has two contact pads where the ma ...

  • Summit HL-630 OPC - page 21

    21 Lexmark T620/622 Lexmark Cartridge Part # 12A6760/12A6860 12A6765/12A6865 OEM Stated Yield: 6760/6860 10,000: 6765/6865 20,000 The “Return” cartridges have an ARD installed on the right side of the cartri dge, (as the cartridge would be inserted into the machine. These chips are physically located in a diffe rent spot from the older Optra T ...

  • Summit HL-630 OPC - page 22

    22 Lexmark W812 (Fuji-Xerox XP-26) Lexmark Cartridge Part # 14K0050 OEM Stated Yield: 12,000 These cartridges use a chip, but it is not the “Killer type” These chips monitor the “Toner Low” as well as tell the machine the brand of cartridge it is. So far we have seen Lexmark, Epson, and IBM machines using these cartridges. The chips for eac ...

  • Summit HL-630 OPC - page 23

    23 Minolta PageWorks 1400 Minolta Toner cartridge Part #9J04203 Minolta Drum Cartridge Part # M4519401 OEM Stated Yield Toner: 2,000 OEM Stated Yield OPC: 20,000 Toner Cartridge: These toner cartridges have a chip that must be replaced each cycle. The chip is located on the bottom left side of the cartridge. There are different chips used for diffe ...

  • Summit HL-630 OPC - page 24

    24 engine is the Okidata OL-400/800 , but the first actual reset procedure is for the OL-800 series only, followed by other machines that use the same engine but have different reset pr ocedures. Just to make things a little crazier, ther e are also m achines that use different engines, but use the same reset procedure. These are grouped as above, ...

  • Summit HL-630 OPC - page 25

    25 Okidata C3000 Series Okidata OPC Color Cartridge Part # 42126661, 42126660, 42126659, 42126658 OEM Stated Yield: 15,000 All These machines have a glass fuse that is used to reset the machine. The fuse is located in the ge ar end cap of the cartridge. We have not confirmed this yet, but we believe that the fuse is the sam e as the SF-5100. The fu ...

  • Summit HL-630 OPC - page 26

    26 Okidata OL-400e OPC Okidata OPC Cartridge Part # 56116801 OEM Stated Yield: 20,000 (The procedure for these machines is the same as used for the Okidata OL-1200, OP-20) Turn off the printer While holding the MENU1/MENU2 button down, turn the printer back on. Keep holding the button down until you see USER MNT on the display panel. Release the bu ...

  • Summit HL-630 OPC - page 27

    27 Okidata OL-1200 OPC Okidata OPC Cartridge Part # 56118801 OEM Stated Yield: 30,000 (The procedure for these machines is the same as used for the Okidata OL-400e, and OP-20) Turn off the printer While holding the MENU1/MENU2 button down, turn the printer back on. Keep holding the button down until you see USER MNT on the display panel. Release th ...

  • Summit HL-630 OPC - page 28

    28 Okidata OP-14e Okidata OPC Cartridge Part #41331601 (Type 8) OEM Stated Yield: 20,000 (The procedure for these machines is the same as used for the Okidata OP-6e, OL-600e, OP-10e) From the computer the printer is directly hooked up to, enter the Printer Status Monito r. Click on the “Printer Menu” tab. Click on the “Maintenance” tab. Cli ...

  • Summit HL-630 OPC - page 29

    29 Panasonic KXP-4420 Toner/4420 OPC Panasonic cartridge Part #’s KX-P451, KX- PDM2 OEM Stated Yield: 18,000 Both of these cartridges use a simple 1/16 amp fuse that must be soldered in. The OEM fuse looks like a black transistor. Most of the replacement fuses being sold are in a resistor t ype package. The physical looks of the fuse don't m ...

  • Summit HL-630 OPC - page 30

    30 will momentarily press in a lever ins ide the machine and start to reset the coun ter. The tap e will then break releasing the lever finishing the reset procedure. Make sure you use a thin tape and not a packing tape, as it is important that the tape break fairly easily. Samsung CLP-300 Toner Cartridges Samsung Toner Cart. # CLP-K300A, CLP- C300 ...

  • Summit HL-630 OPC - page 31

    31 Samsung CLP-600 Toner/OPC Cartridges Samsung Cart. # CLP-K600A, CLP-C600A, CLP-M600A, CLP-Y600A OEM Stated Yield: 4,000 Black, 4,000 Color These cartridges use a chip that must be replaced each cycle. The chip is located on the rear of the waste hopper. There is no known reset method through the printers menu. Samsung ML-1210 Toner Cartridges Sa ...

  • Summit HL-630 OPC - page 32

    32 Samsung ML-2150 Toner Cartridges Samsung Cart. # ML-2150D8/XAA OEM Stated Yield: 8,000 These are the first Samsung cartridges to use a chip. The chips can sometimes be used another cycle, b ut to be safe it is best to replace them each cycle. There are different manufacturers using this engine. Each manufacturer has it’s own separate chip. Res ...

  • Summit HL-630 OPC - page 33

    33 Samsung SCX-6320Toner/OPC Cartridges Samsung Cart. # SCX-6320D8 (Toner), SCX- 6320R2 (Drum) OEM Stated Yield: 8,000, 18,000 respectively Both of these cartridges use diff erent item s to reset the printer. The toner cartr idge uses a chip th at must be replaced/reset each cycle . There are different manufacturers using this engine. Each manufact ...

  • Summit HL-630 OPC - page 34

    34 pages. These cartridges are designed to be recycled by Sharp authorized dealers. As such, replacement chips are available from authorized S harp dealers, and now generic chips are al so available. Since the chip shuts down the cartridge at 10,000 pages, you can recycle the cartridge 2-3 times with the s ame chip with out any problems . However, ...

  • Summit HL-630 OPC - page 35

    35 actuator (or flag) is next to the sm all gear). On some cartridges the "flag gear" is now black. It is located to the bottom right of the wh ite gear. Make sure that when you snap the green end cap back on, the notch on the small gear lines up with the tab on the la rge single gear that is on th e cartridge. Once everything lines up, s ...

  • Summit HL-630 OPC - page 36

    36 Sharp AR-152 Developer Sharp Cartridge Part # AR-152DV OEM Stated Yield: 25,000 The developer is rated for 25,000 pages. The default setting on the machine is to keep running even after the 25K pages. That default setting can be set by the dealer to stop at 25K pages. It is considered a dealer option. To clear the developer afte r a stop, or to ...

  • Summit HL-630 OPC - page 37

    37 Sharp Cartridge Part # AR-201ND OEM Stated Yield: 30,000 The developer is rated for 30,000 pages. The default setting on the machine is to keep running even after the 30K pages. That default setting can be set by the dealer to stop at 30K pages. It is considered a dealer option. To enter the simulation mode, press the "CLEAR KEY", &quo ...

  • Summit HL-630 OPC - page 38

    38 OEM Stated Yield: 20,000 (All) These cartridges do not use any reset procedures at all. According to the Sharp manual, they should be replaced when the copy quality deteriorates. No codes will show on the display to change the cartridge. NOTE: None of these cartridges are interchangeable, they all are slightly different. Sharp AL-800 Sharp Part ...

  • Summit HL-630 OPC - page 39

    39 The display will read PCU DIAG MODE G. Press the MENU key repeatedly until you see COUNTER SET. Press the ENTER key once, and the MENU key twice. The display will read DRM 05000. Press and hold the DOWN ARROW key until the number resets to 00000. Press the MENU key four times, the Display will read: DTRM XXXXX Press and hold the DOWN ARROW key u ...

  • Summit HL-630 OPC - page 40

    40 Turn the power off. Hold down the exposure button, and turn the power on. All the lights except the ready light will come on. Releas e the exposure button. Press the exposure butto n again and hold for 10 seconds, until the three exposure lights come on. Release the exposure butt on. Once the ready light comes on the counter is reset. Turn the p ...

  • Summit HL-630 OPC - page 41

    41 TEC LB-1305 OPC OEM Stated Yield: 10,000 (All) There are three major versions of these cartridges. Two use an external counter and one doesn't use one at all. The older style 13 05 has no counter. The label on top of the cartridge has a place to write down the starting page count. You are supposed to keep track of the pages printed. The nex ...

  • Summit HL-630 OPC - page 42

    42 type of replacement cartridge that the machine is expecting. 001=113R180/181, 005 = 113R287. If the cartridges your machin e needs is not available, you can change what type of cartridge the machine will accept by doing the following. E nter the diagnostics mode as in a bove. Enter “406 “ and press Print. Turn off the power and install the c ...

  • Summit HL-630 OPC - page 43

    43 cartridge is changed. A ne w fuse is not needed. However if the machine says change cartridge, the fuse is needed. Since you really have no way to know the state of your customer’s machine, we recommend that the fuse be replaced each cycle. These fuses are very inexpensive, and this way you have no worries! Starter car tridges can come with pl ...

  • Summit HL-630 OPC - page 44

    44 use the correct connector. The 5012 will not work in the 5011 and vice-versa. To tell if you have the correct connector, read the resistance between pin’s 3 & 6. 5011 connectors read 15,000 ohms while 5012 connectors read 1,500 ohm Xerox 5012/5014 OPC 13R19 OEM Stated Yield: 18,000 The 5012 OPC cartridges look very similar to the 1012 and ...

  • Summit HL-630 OPC - page 45

    45 Xerox 5113 Series (5113, 5114, 5614) Xerox Cartridge Part # 113R79 OEM Stated Yield: 18,000 To reset the counter in the 5113 OPC cartridges the connector on the rear of the cartridge m ust be replaced. This will clear the J7 or J8 codes. J7= change copy cartridge, J8 = wrong or bad connector. There are many different cartridges that use differen ...

  • Summit HL-630 OPC - page 46

    46 Xerox 5318/5340 Xerox Cartridge Part # 13R75/13R56 OEM Stated Yield: 25,000 To reset the counter in the 5318 OPC cartridges the connector on the rear of the cartridge m ust be replaced. This will clear the J7 or J8 codes. J7= change copy cartridge, J8 = wrong or bad connector. There are different connectors used in the 5318 and 5340 cartridges. ...

Manufacturer Summit Category Printer Accessories

Documents that we receive from a manufacturer of a Summit HL-630 OPC can be divided into several groups. They are, among others:
- Summit technical drawings
- HL-630 OPC manuals
- Summit product data sheets
- information booklets
- or energy labels Summit HL-630 OPC
All of them are important, but the most important information from the point of view of use of the device are in the user manual Summit HL-630 OPC.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Summit HL-630 OPC, service manual, brief instructions and user manuals Summit HL-630 OPC. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Summit HL-630 OPC.

Similar manuals

A complete manual for the device Summit HL-630 OPC, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Summit HL-630 OPC by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Summit HL-630 OPC.

A complete Summit manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Summit HL-630 OPC - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Summit HL-630 OPC, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Summit HL-630 OPC, that we can find in the current document
3. Tips how to use the basic functions of the device Summit HL-630 OPC - which should help us in our first steps of using Summit HL-630 OPC
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Summit HL-630 OPC
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Summit HL-630 OPC in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Summit HL-630 OPC?

Use the form below

If you did not solve your problem by using a manual Summit HL-630 OPC, ask a question using the form below. If a user had a similar problem with Summit HL-630 OPC it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)