English dropdown-ico

Manual Quadra-Fire 7008-115

43 pages 3.14 mb
Download

Go to site of 43

Summary
  • Quadra-Fire 7008-115 - page 1

    1 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 Model: HUDBA Y -INS • DO NOT store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - DO NOT try to light any appliance. - DO NOT touch any electrical switch. DO NOT use any phone in your building ...

  • Quadra-Fire 7008-115 - page 2

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 2 Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on fi replace: _____________________ Dealership purchased from: _______________________________ Dealer Phone: ________ ...

  • Quadra-Fire 7008-115 - page 3

    3 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury . • W ARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury . • CAUTION! Indicates a hazardous situation which, ...

  • Quadra-Fire 7008-115 - page 4

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 4 B. Limited Lifetime W arranty 4021-645C 12-29-10 Page 1 of 2 Hearth & Home T echnologies Inc. LIMITED LIFETIME W ARRANTY Hearth & Home T echnologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electric hear ...

  • Quadra-Fire 7008-115 - page 5

    5 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 B. Limited Lifetime W arranty (continued) 4021-645C 12-29-10 Page 2 of 2 W ARRANTY CONDITIONS:  7KLVZDUUDQWRQOFRYHUV++7DSSOLDQFHVWKDWDUHSXUFKDVHGW KURXJKDQ++7 DXWKRUL]HGGHDOHURUGLVWULEXWRU  $ OLVWRI ++7DXWKRUL]HGG ...

  • Quadra-Fire 7008-115 - page 6

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 6 C. BTU Speci fi cations This product is listed to ANSI standards for “V ented Gas Appliance Heaters” and applicable sections of “Gas Burn- ing Heating Appliances for Manufactured Homes and Recreational V ehicles”, and “Gas Fired Appliances for Use at High Altitudes”. Quadra ...

  • Quadra-Fire 7008-115 - page 7

    7 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 2 2 Operat ing Instruc tions Figure 2.1 General Operating Parts B. Y our Fireplace W ARNING! DO NOT operate fi replace before read- ing and understanding operating instructions. Failure to operate fi replace according to operating instructions could cause fi re or injury . DECORA TIV ...

  • Quadra-Fire 7008-115 - page 8

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 8 C. Clear Space W ARNING! DO NOT place combustible objects in front of the fi replace or block louvers. High temperatures may start a fi re. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or hearth. Heat may damage these objects. Figure 2.2 Clear Space ...

  • Quadra-Fire 7008-115 - page 9

    9 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 H. Standing Pilot Ignition 1. Set the thermostat to lowest setting. 2. T urn off all electric power to the appliance if service is to be performed. 3. Push in gas control knob slightly and turn clockwise to "OFF" position. FOR YOUR SAFETY READ BEFORE LIGHTING FOR YOUR SAFETY R ...

  • Quadra-Fire 7008-115 - page 10

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 10 Initial Break-in Procedure • The appliance should be run three to four hours continuously on high. • T urn the appliance off and allow it to completely cool. • Remove fi xed glass assembly . See Section 12.L. • Clean fi xed glass assembly . See Section 3. • Replace the fi ...

  • Quadra-Fire 7008-115 - page 11

    11 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 Glass Cleaning Frequency: Seasonally By: Homeowner T ools Needed : Protective gloves, glass cleaner , drop cloth and a stable work surface. CAUTION! Handle fi xed glass assembly with care. Glass is breakable. • Avoid striking, scratching or slamming glass • Avoid abrasive cleaners ...

  • Quadra-Fire 7008-115 - page 12

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 12 B. Maintenance T asks-Service T echnician The following tasks must be performed by a quali fi ed technician. Gasket Seal and Glass Assembly Inspection Frequency: Annually By: Service T echnician T ools needed: Protective gloves, drop cloth and a stable work surface. • Inspect gasket ...

  • Quadra-Fire 7008-115 - page 13

    13 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 A. T ypical Appliance System NOTICE: Illustrations and photos re fl ect typical installations and are for design purposes only . Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual VERTICAL TERMINA TION CAP (SECTION 8F ) VENT PIPE (SECTION 8) ...

  • Quadra-Fire 7008-115 - page 14

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 14 B. Design and Installation Considerations Quadra-Fire gas inserts are designed for installations into solid fuel masonry or factory built fi replaces that have been installed in accordance with the National, Provin- cial, State and local building codes. Fireplaces are to be constructe ...

  • Quadra-Fire 7008-115 - page 15

    15 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 5 5 F ireplace Size Requirements A. Minimum Fireplace Opening Minimum fi replace opening requirements are shown in Figure 5.1. W ARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access. Due to high temperatures, the appliance should be loca ...

  • Quadra-Fire 7008-115 - page 16

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 16 B. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as speci fi ed. Framing or fi nishing material closer than the minimums listed must be construct- ed entirely of noncombustible materials (i.e., steel studs, concrete board, e ...

  • Quadra-Fire 7008-115 - page 17

    17 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 A. V ent T ermination Minimum Clearances Roof Pitch H (Min.) Ft. Flat to 6/12...........................................................1.0* Over 6/12 to 7/12 .................................................1.25* Over 7/12 to 8/12 .................................................1.5* ...

  • Quadra-Fire 7008-115 - page 18

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 18 7 7 Installation Preparation Prepare the existing solid fuel masonry or factory built non-combustible fi rebox for installation. A. Inspection and Cleaning Prior to installing the gas insert: • Have the chimney and adjacent structure inspected and cleaned by quali fi ed professiona ...

  • Quadra-Fire 7008-115 - page 19

    19 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 B. V enting Components CAUTION! Risk of Cuts/Abrasions/Flying Debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp. The vertical vent termination system installed on this model includes: • Flexible vent pipe for exhaust air (included wi ...

  • Quadra-Fire 7008-115 - page 20

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 20 Figure 8.2 CUT AND BEND FLASHING AS NEEDED TO FIT CHIMNEY SEALANT ADHESIVE • T rim chimney top plate to minimize excess overhang or bend over fl ue tile (see Figure 8.2). • Place 3/8 inch bead of silicone (minimum of 30 0 ºF continuous exposure rating ) on fl ue tile top. D. Pla ...

  • Quadra-Fire 7008-115 - page 21

    21 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 F . Installing Adaptor and T ermination Cap For installation of termination cap see minimum vent heights for various pitched roofs (see Figure 8.4) . T o install adaptor see Figure 8.5. Roof Pitch H (Min.) Ft. Flat to 6/12.................... 1.0* Over 6/12 to 7/12 ........ 1.25* Over ...

  • Quadra-Fire 7008-115 - page 22

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 22 A. Fuel Conversion • Make sure the appliance is compatible with available gas types. • Conversions must be made by a quali fi ed technician (NFI certi fi ed or factory-trained) using Hearth & Home T echnologies speci fi ed and approved parts. 9 9 Gas Informat ion Kit content ...

  • Quadra-Fire 7008-115 - page 23

    23 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 Figure 9.5 Figure 9.6 Figure 9.7 Note: Do not rem ov e retainin g clip fro m the pilot h ood. Note: If instal ling brick al so, do so now before reassem bling. If not insta lling b r ick, reas s em b le bu r ner in reverse orde r of remov al. With a 5/8 in. wrench remove the ori fi ce ...

  • Quadra-Fire 7008-115 - page 24

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 24 E. Gas Connection • Refer to Reference Section 15 for location of gas line access in appliance. • Gas line may be run through knockout(s) provided. • T he gap between supply piping and gas acc ess hole may be caulked with caulk with a minimum of 3 00 º F c o n t i n u o u s e x ...

  • Quadra-Fire 7008-115 - page 25

    25 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 NOTICE: DO NOT wire 1 10 V AC to the millivolt valve! This will damage the valve. ON/OFF Switch • An ON/OFF switch is included with appliance and should be attached to surround/facing. • If desired an additional wall switch, thermostat, or remote control may be added to system as s ...

  • Quadra-Fire 7008-115 - page 26

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 26 C. Blower Installation Included in kit: Blower . T ools required: Powered Phillips head screwdriver . Figure 10.2 Figure 10.3 Figure 10.4 Turn off gas and disconnect appliance from electricity. Remove logs and burner from appliance. Remove blower access cover in bottom of firebox by re ...

  • Quadra-Fire 7008-115 - page 27

    27 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 Figure 10.7 Blower Wiring Diagram F = 1/4 in. (6 mm) female spade M = 1/4 in. (6 mm) male spade BLOWER M M F F BLK BLK WHT WHT BLK R F M M F F M WHT BLK BLK WHT GRN RHEOST A T SNAP DISC ...

  • Quadra-Fire 7008-115 - page 28

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 28 1 1 11 F inishing A. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as speci fi ed. Framing or fi nishing material closer than the minimums listed must be construct- ed entirely of noncombustible materials (i.e., steel studs, ...

  • Quadra-Fire 7008-115 - page 29

    29 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 A. Remove Glass Assembly See Section 12.L. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the fi rebox. C. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the fi rebox or underneath in the control cavity . D. Accesso ...

  • Quadra-Fire 7008-115 - page 30

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 30 F . Grille Installation Remove the door of appliance. Remove the four screws (two at each end) holding grille in place. Lift up to remove. Figure 12.5 Determine your desired placement of the rocker switch. 1 If you wish to place it on the control panel in the "Main Burner" op ...

  • Quadra-Fire 7008-115 - page 31

    31 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 H. Ember Placement W ARNING! Risk of Explosion! Follow ember placement instructions in manual. DO NOT place embers directly over burner ports. Replace ember material annually . Improperly placed embers interfere with proper burner operation. Ember material is shipped with this gas appl ...

  • Quadra-Fire 7008-115 - page 32

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 32 I. Brick Installation The pilot shield has to be removed to install or remove the brick refractory . Removal of the bracket requires remov- ing two screws. Figure 12.1 1 Figure 12.12 Figure 12.13 Figure 12.14 Figure 12.15 Figure 12.10 PILOT BRACKET PILOT SHIELD T o install the baf fl ...

  • Quadra-Fire 7008-115 - page 33

    33 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 Figure 12.16 Note: For th e Hudso n Bay Inser t t he lower b ric k retain er is used. REAR BRICK REAR BRICK RET AINING T ABS RET AINING T ABS J. Positioning the Logs While still breakable, the logs do not become fragile until after the appliance is burned and they have cured. After cur ...

  • Quadra-Fire 7008-115 - page 34

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 34 Figure 12.24 Figure 12.25 Figure 12.26 Note: Do not clo se so much as to c ause a soot y fl ame. Impro per adjustment c an cause so oting in the fi rebox and/or on the o utside of a ho use with a ho rizont al terminat ion. OPENS LEFT CLOSES RIGHT The air shutter is located on the und ...

  • Quadra-Fire 7008-115 - page 35

    35 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 L. Fixed Glass Assembly Removing Fixed Glass Assembly W ARNING! Risk of Asphyxiation! Handle fi xed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches. • DO NOT strike, slam or scratch glass. • DO NOT operate ...

  • Quadra-Fire 7008-115 - page 36

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 36 A. Standing Pilot Ignition System 1 3 13 T roubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a quali fi ed technician in the diagnosi ...

  • Quadra-Fire 7008-115 - page 37

    37 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 T roubleshooting (continued) Symptom Possible Cause Corrective Action 3. (Continued) C. V alve. T urn the valve knob to the ON position. Place the ON/ OFF switch in the ON position. T ake a reading with a millivolt meter at the thermopile terminals. The millivolt meter should read grea ...

  • Quadra-Fire 7008-115 - page 38

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 38 1 4 14 Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. Figure 14.1 Appliance Dimensions MINIMUM FIREBOX OPENING Height: Width: Depth: Front Rear Front Rear T op Bottom Inches 20-1/4 14-1/2 26-1/2 20 13 13 Millimeter ...

  • Quadra-Fire 7008-115 - page 39

    39 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 B. V ent Kits Components Direct V ent Flex Liner Kits (see Figure 14.2) LINK-DV30B: Masonry 3 inch fl ex liner kit. Expands to 30 feet. Includes: two liners, termination cap, fl ashing, and link adapter . LINK-DV4-30B: Masonry 3 inch fl ex liner kit. Expands to 30 feet and 4 feet re ...

  • Quadra-Fire 7008-115 - page 40

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 40 R C. Service Parts Hudson Bay Insert HUDBA Y -INS Beginning Manufacturing Date: April 2003 Ending Manufacturing Date: ______ Part number list on following page. Log Set Assembly 1 11 10 9 7 6 8 12 13 2 3 4 5 ...

  • Quadra-Fire 7008-115 - page 41

    41 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 HUDBA Y -INS C. Service Parts List IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked In Depot ITEM ...

  • Quadra-Fire 7008-115 - page 42

    Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 42 R Service Parts HUDBA Y -INS Beginning Manufacturing Date: April 2003 Ending Manufacturing Date: ______ IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this man ...

  • Quadra-Fire 7008-115 - page 43

    43 Quadra-Fire • HUDBA Y -INS • 7008-1 15 Rev . o • 8/1 1 Quadra-Fire, a brand of Hearth & Home T echnologies Inc. 7571 215 th Street West, Lakeville, MN 55044 www .quadra- fi re.com D. Contact Information Please contact your Quadra-Fire dealer with any questions or concerns. For the location of your nearest Quadra-Fire dealer , please v ...

Manufacturer Quadra-Fire Category Indoor Fireplace

Documents that we receive from a manufacturer of a Quadra-Fire 7008-115 can be divided into several groups. They are, among others:
- Quadra-Fire technical drawings
- 7008-115 manuals
- Quadra-Fire product data sheets
- information booklets
- or energy labels Quadra-Fire 7008-115
All of them are important, but the most important information from the point of view of use of the device are in the user manual Quadra-Fire 7008-115.

A group of documents referred to as user manuals is also divided into more specific types, such as: Installation manuals Quadra-Fire 7008-115, service manual, brief instructions and user manuals Quadra-Fire 7008-115. Depending on your needs, you should look for the document you need. In our website you can view the most popular manual of the product Quadra-Fire 7008-115.

Similar manuals

A complete manual for the device Quadra-Fire 7008-115, how should it look like?
A manual, also referred to as a user manual, or simply "instructions" is a technical document designed to assist in the use Quadra-Fire 7008-115 by users. Manuals are usually written by a technical writer, but in a language understandable to all users of Quadra-Fire 7008-115.

A complete Quadra-Fire manual, should contain several basic components. Some of them are less important, such as: cover / title page or copyright page. However, the remaining part should provide us with information that is important from the point of view of the user.

1. Preface and tips on how to use the manual Quadra-Fire 7008-115 - At the beginning of each manual we should find clues about how to use the guidelines. It should include information about the location of the Contents of the Quadra-Fire 7008-115, FAQ or common problems, i.e. places that are most often searched by users in each manual
2. Contents - index of all tips concerning the Quadra-Fire 7008-115, that we can find in the current document
3. Tips how to use the basic functions of the device Quadra-Fire 7008-115 - which should help us in our first steps of using Quadra-Fire 7008-115
4. Troubleshooting - systematic sequence of activities that will help us diagnose and subsequently solve the most important problems with Quadra-Fire 7008-115
5. FAQ - Frequently Asked Questions
6. Contact detailsInformation about where to look for contact to the manufacturer/service of Quadra-Fire 7008-115 in a specific country, if it was not possible to solve the problem on our own.

Do you have a question concerning Quadra-Fire 7008-115?

Use the form below

If you did not solve your problem by using a manual Quadra-Fire 7008-115, ask a question using the form below. If a user had a similar problem with Quadra-Fire 7008-115 it is likely that he will want to share the way to solve it.

Copy the text from the picture

Captcha
New picture

Comments (0)