-
Roland TD-3KW - page 1
TD-3KW Thank you, and congratulations on your choice of the Roland Drum System TD-3KW. * For the Snare (PDX-8) to function correctly, trigger parameters in the sound module TD-3 must be adjusted. 202 Copyright © 2006 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ...
-
Roland TD-3KW - page 2
2 USING THE UNIT SAFELY 001 • Before using this unit, make sure to read the instructions below, and the Owner’s Manual. ................................................................................................ 002b • Do not open or perform any internal modifications on the unit. (The only exception would be where this manual provides s ...
-
Roland TD-3KW - page 3
3 291a In addition to the items listed under “USING THE UNIT SAFELY” on page 2, please read and observe the following: Placement 354a • Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. Excessive heat can deform or discolor ...
-
Roland TD-3KW - page 4
4 ❑ TD-3 (Percussion Sound Module) x 1 ❑ KD-8 (Kick Trigger Pad) x 1 ❑ FD-8 (Hi-Hat Control Pedal) x 1 ❑ PDX-8 (V-Pad) x 1 ❑ PD-8 (Pad) x 3 ❑ CY-5 (Cymbal Pad) x 1 ❑ CY-8 (Cymbal Pad) x 2 ❑ Connection Cables ❑ Tuning Key x 1 ■ TD-3KW Owner’s Manual x 1 ❑ PLAY-ALONG AUDIO CD Set x 1 ❑ PLAY-ALONG AUDIO CD ❑ Connection Cabl ...
-
Roland TD-3KW - page 5
5 USING THE UNIT SAFELY fig.PD-85.e_80 add * Do NOT place your fingers inside the shell, as you may hurt yourself or cause damage to the PDX-8. Or when changing the head, do NOT touch any of the internal parts. Also, do not insert your fingers into the hole of the mounting bracket. fig.Stand.j fig.Stand.j Before using the pad, tighten the head so t ...
-
Roland TD-3KW - page 6
6 USING THE UNIT SAFELY Attach the PDX-8 to a pad mount of the stand. Be sure to tighten the stand fixing screw securel. If it remain loose, double triggering may occur. fig.Stand.e Head Shots fig.HeadShot.e * Do not strike the hoop. Rim Shots fig.RimShot.e * To play rim shots, strike the rim in the area shown in the diagram. fig.RimShot.e Cross St ...
-
Roland TD-3KW - page 7
7 USING THE UNIT SAFELY When the Head Should Be Replaced The head is an expendable item that eventually will wear out and need to be replaced. Replace the head when the following occurs: Slack portions remain in the head even when the head tension is properly adjusted. Replacement heads (optional): MH-8 Mesh Head 1. Remove all tuning bolts from the ...
-
Roland TD-3KW - page 8
8 USING THE UNIT SAFELY fig.PD-8.e fig.PD-Set.e When attaching the PD-8s to the mounts, be sure to tighten the stand fixing screws securely. If any of them remain loose, the pad could fall off. fig.PD-HR.e PD-8 Pad Size: 8.5 inches Triggers: 2 (Head, Rim) Dimensions: 226 (W) x 280 (D) x 54 (H) mm 8-15/16 (W) x 11-1/16 (W) x 2-1/8 (H) inches Weight: ...
-
Roland TD-3KW - page 9
9 USING THE UNIT SAFELY fig.CY-8.e When mounting the CY-5 on an L-Rod (pad mount), use ONLY the attachment set as shown below. 1. Mounting the lower clutch and the clutch felt (L). Align the notched section as shown below. Then place the clutch felt (L) so it fits securely. 2. Mount the CY-5 so it fits the lower clutch as shown below. 3. Place the ...
-
Roland TD-3KW - page 10
10 USING THE UNIT SAFELY fig.CY-8. 1. Use a tuning key to tighten the stopper bolt. The stopper keeps the cymbal pad from turning, and prevents the cables from catching or getting tangled on the stand. fig.CY-Set01.e 2. Attach the CY-8 so the Roland logo is positioned on the opposite side of the playing area. 3. Tighten the wing nut to obtain the d ...
-
Roland TD-3KW - page 11
11 USING THE UNIT SAFELY fig.FD-8.e • The tips of the anchor bolts are sharp. Handle with care. • When using on flooring, the anchor bolts may damage the floor. Do not attach the anchor bolts. • When the FD-8 is not going to be used for a long period of time, move and fix the arm, allowing longer travel for the pedal. • To avoid damage, do ...
-
Roland TD-3KW - page 12
12 USING THE UNIT SAFELY fig.KD-8.e 1. Remove the screws attached to the reverse side of the KD-8’s trigger. fig.KD-Assy01 2. Pull out the stand in the direction indicated by the arrow until it is fully extended. fig.KD-Assy02 3. Use a tuning key supplied with the FD-8 to tighten the screws removed in Step 1 so that the stand is firmly secured. f ...
-
Roland TD-3KW - page 13
13 USING THE UNIT SAFELY 1. Loosen the stand’s anchor bolts and remove the foot plate. fig.KD-Assy06 2. Set the kick pedal so that the entire bottom surface is attached to the floor. 3. In most cases, the stand becomes somewhat floated. Tighten the anchor bolts securely there to fix the stand and foot plate. fig.KD-Assy07.e • Install the kick p ...
-
Roland TD-3KW - page 14
14 USING THE UNIT SAFELY . 921 Using the provided cables, connect the pads. Connect the L-shaped plugs of the included cables to the pads. To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. fig.Setting1.e fig.Label 1. Insert the plugs o ...
-
Roland TD-3KW - page 15
15 USING THE UNIT SAFELY . For the Snare (PDX-8) to function correctly, trigger parameters in the sound module TD-3 must be adjusted. For more detailed informations, refer to the TD-3 Owner’s Manual. . When adding a new pad, use trigger input CRASH2. Adding a Cymbal Adding the CY-8 or the CY-5 for a 2nd Crash or a Splash Cymbal. For mounting, use ...
-
Roland TD-3KW - page 16
04234178 3PR As of August 1, 2006 (ROLAND) Information When you need repair service, call your nearest Roland Service Center or authorized Roland distributor in your country as shown below. EGYPT Al Fanny Trading Office 9, EBN Hagar A1 Askalany Street, ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: 20-2-417-1828 REUNION Maison FO - YAM Marcel 25 ...
У вас вопрос, касающийся Roland TD-3KW?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Roland TD-3KW, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Roland TD-3KW со всей вероятностью он захочет поделиться методом ее решения.