-
Eminent EM8622 - page 1
EM8622 Wireless Control Panel ...
-
Eminent EM8622 - page 2
2 | ENGLISH EM8622 - Wireless Control Panel Table of contents 1.0 Introduction ...... ...... ......... ...... ..... ...... ......... ...... ...... ..... ......... ...... ...... ...... ........ ...... .. 3 1.1 Packing content s ...... ......... ...... ...... ..... ......... ...... ...... ...... ........ ...... ...... ...... ...... .... 3 1.2 Control ...
-
Eminent EM8622 - page 3
3 | ENGLISH 1.0 Introduction Congratulations w ith the purchase of thi s high-quality Eminent product ! This prod uct has undergone ex tensive testing by Eminen t’s technical ex perts. Should you experience any pro blems with this pro duct, you are covered by a five- year Eminent warranty. Please keep this manual and the receipt in a safe place. ...
-
Eminent EM8622 - page 4
4 | ENGLISH 1.3 Control panel ins ide 2.0 Installation Install the batteries and mount the control panel on the door fra me or the w all before use. Battery contact, plea se check positive and negative terminals Battery compartment Tamper switch Wired cable connection Red wire = + 12V Black wire = - GND ...
-
Eminent EM8622 - page 5
5 | ENGLISH 1) Remove the screw and open the ca se 2) Install the batteries ac cording to th e positive and negative sign s (Re move the insulating strip be fore the first use) 3) Mount the backcover on the door fr ame or wall 4) Close the case and replace the sc rew Note : Opening the cover will trigger the tamp er switch ! You can disar m it by e ...
-
Eminent EM8622 - page 6
6 | ENGLISH If there is an intru sion the alarm sy stem will be trigger ed, the siren w ill hoot and the alarm sy stem will send an SMS and au to dial to pre-stored phone numbers to notify u sers. Note : When an en try delay is set, the external control pane l will NOT warn you with an audio signal when a sensor is t riggered. Only the alarm system ...
-
Eminent EM8622 - page 7
7 | ENGLISH 3.2.2 Using RFID Tag to disarm If direct disar m by RFID tag is disa bled (this is the defaul t power saving mode when using batteries), u ser needs to press [* ] to wake up the control panel and then put RFID tag close to the reade r to di sarm the alar m system.. When the pow er saving function is disabled, user can put the RFID t ag ...
-
Eminent EM8622 - page 8
8 | ENGLISH 3.2.4 Emergency Call When the control panel is in SOS Speed Dial mode, u ser just holds the [SOS] key for 3 seconds, the LED indicator flashes once, the con trol panel beeps once, and the alarm system alar ms immediately. When the control panel is not in SOS Speed Dial mode , user needs to inpu t user code or admin code befor e holding ...
-
Eminent EM8622 - page 9
9 | ENGLISH 4.0 Connect to the alarm sy stem Note : The default admin code is : 1 23456. See chapter “Ch ange Ad min Code” to change it. Note : The default user code is : 12 34. See chapter “Change User Code” to change it. Make sure the alar m system is in connection state (pres s code on alarm syste m and press the me mo button). Input the ...
-
Eminent EM8622 - page 10
10 | ENGLISH 3. Put the RFID tag close to the RFID re ader. If one beep is heard the connecting is successful. When 2 beeps are hea rd, the RFID tag w as already connected to the control panel. To remove all conne cted RFID tag s, input the admin code followed by the # button. Press and hold down the 9 button for six seconds. All RFID tags are clea ...
-
Eminent EM8622 - page 11
11 | ENGLISH 6.0 Settings Before changing the settings of th e control panel, the control panel sho uld be in “setup-state”. 6.1 Enter Setup-s tate Note : The default adm in code is : 123456 Input the admin code fol lowed by the [#] button to w ake up the control panel. Press [3] to enter the se tup-state. The LED indicator w ill be on. Note : ...
-
Eminent EM8622 - page 12
12 | ENGLISH After setting a delay time, press the [Arm] button on the con trol pan el. The control panel will send the Arm command to the alarm system afte r the delay time you set in the control panel . Note : This setting will not apply to the Hom e mode. If both the control panel and the alarm system ha ve a delay time set, the a ctual delay ti ...
-
Eminent EM8622 - page 13
13 | ENGLISH 6.3.1 Disable SO S code Enter Setup-state and input : When one beep i s heard and the L ED indicator keeps on for 10 seconds, the setup is successful. 6.3.2 Enable SOS code Enter Setup-state and input : When one beep i s heard and the L ED indicator keeps on for 10 seconds, the setup is successful. Note : Default setting i s 0, SOS cod ...
-
Eminent EM8622 - page 14
14 | ENGLISH 6.4 Keyboard tone Keyboard tones can be switched o n or off. If they are switched of f, the beep when a setup is successful w ill also be swit ched off ! 6.4.1 Disable key board tone Enter Setup-state and input : When one beep i s heard and the L ED indicator keeps on for 10 seconds, the setup is successful. 6.4.2 Enable key board tone ...
-
Eminent EM8622 - page 15
15 | ENGLISH 6.5 Disarm system by RFID tag Users can enable or disable the function of d isarming the alar m system by RFID tag , or disarming silent by RFID tag. 6.5.1 Disable disar ming by RFID tag Enter Setup-state and input : When one beep i s heard and the L ED indicator keeps on for 10 seconds, the setup is successful. 6.5.2 Enable disarming ...
-
Eminent EM8622 - page 16
16 | ENGLISH 6.5.3 Disarming silently by RFID tag The alarm panel an d siren will hoo t twice when disar ming the alarm system by RFID tag. If set disar ming silently by RFID tag, the alarm syste m and siren will keep silent when disarming. Enter Setup-state and input : When one beep i s heard and the L ED indicator keeps on for 10 seconds, the set ...
-
Eminent EM8622 - page 17
17 | ENGLISH 6.6.1 Enable power savi g mode Enter Setup-state and input : When one beep i s heard and the L ED indicator keeps on for 10 seconds, the setup is successful. 6.6.2 Disable po wer saving mod e If the control panel is powered by an external 12V pow er supply (not included), i t is recommended to switch of the po wer saving mode. User s c ...
-
Eminent EM8622 - page 18
18 | ENGLISH 6.7 Change user code A user can use its own code to wake up the control panel and send Ar m, Disarm or Home mode command s to the alarm syste m. The control panel can only hav e one user code. Note : The default user code is 1234. Please change this code at first use ! Enter Setup-state and input : When one beep i s heard and the L ED ...
-
Eminent EM8622 - page 19
19 | ENGLISH 6.9 Reset the control panel After a reset the u ser code, admin code and all other setting s will be restored to default. Only the connected RFID t ags will remain wo rking. To remove the conne cted RFID tags, please refer to chapter “Connect RFID Tag to control panel”. Enter Setup-state and input : When one beep i s heard and the ...
-
Eminent EM8622 - page 20
20 | ENGLISH 8.0 Service and su pport This user’s manual has been carefu lly written by Eminen t’s technical experts. If you have problems in stalling or using t he product, please fill out the support for m at the website www .eminent-online.com/supp ort . You can also conta ct us by phone. Below you w ill find a list with phone nu mbers for e ...
-
Eminent EM8622 - page 21
21 | ENGLISH 9.0 Warning and p oints of attention Due to laws, directive s and regulat ions set out by the Europ ean parlia ment, some (wireless) devices could be subject to limitations concerning i ts use in certain European member states. In certai n European member states the use of su ch devices could be prohibited. Con tact your ( local) gover ...
-
Eminent EM8622 - page 22
22 | ENGLISH 10.0 Warranty conditions The five-year Eminen t warranty ap plies to all Eminent produc ts, unless mentione d otherwise before or during the momen t of purchase. After buy ing a second -hand Eminent produc t the remaining per iod of warranty is measured from the moment of purchase by the produ ct’s initial ow ner. Eminent warran ty a ...
-
Eminent EM8622 - page 23
23 | ENGLISH 11.0 Declaration of Conformity Application of Council Dire ctives: Manufacturer’s Na me: Eminent Type of Equip ment: Control panel Equipment Class: Commercial, Light Industrial, Cons umer PRODUCTNUM BER: EM8622 Conforms to the following standar ds: EN 301 489-1 V1.9.2 :2011 EN 301 489-3 V1.4.1 :2002 EN 300 220-1 V2.3.1 :2010 EN 300 2 ...
У вас вопрос, касающийся Eminent EM8622?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Eminent EM8622, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Eminent EM8622 со всей вероятностью он захочет поделиться методом ее решения.