-
AMD LE-366 - page 1
LE-366 AMD Geode TM LX800 3.5” Embeded Boar d User ’ s Manual Edition 1.0 2008/02/20 ...
-
AMD LE-366 - page 2
LE-366 User ’ s Manual -1- Copyright Copyright 2006. All rights r e served. This document is copyrighted a nd all rights are reserved. The information in this document is subjec t to change without prior notice to make improvements to the products. This document contains propr ietary information and protected by copyright. No part of this documen ...
-
AMD LE-366 - page 3
LE-366 User ’ s Manual -2- Packing List Please check the package before y ou st arting setup the system. Hardware: LE-366 series motherboard x 1 Cable Kit: Printed Matters: User ’ s Manual x 1 Driver CD x 1 Floppy Cable x 1 44-pin A T A33 IDE Cable x 1 44pin 44pin 40pin Power Cable x 1 PS2 keyboard & mouse cable DC_IN Power Cable x 1 RS232 ...
-
AMD LE-366 - page 4
LE-366 User ’ s Manual -3- Inde x Chapter 1 <Introduction> .................................................................... 6 1.1 <Product Overview> ............................................................................... 6 1.2 <Product Sp ecificatio n> ................................................................. ...
-
AMD LE-366 - page 5
LE-366 User ’ s Manual -4- A.7 <PS/2 Keyboard & Mouse Po rt> .......................................................... 35 Appendix B <Flash BIOS> ................................................................ 37 B.1 BIOS Auto Flash Tool ................................................................37 B.2 Flash Method ........ ...
-
AMD LE-366 - page 6
LE-366 User ’ s Manual -5- (The Page is Left For Blank) ...
-
AMD LE-366 - page 7
LE-366 User ’ s Manual - 6 - Chapter 1 <Introduction> 1.1 <Product Overview> LE-366 is the Mini-IT X motherboard with AMD Geode LX800 pl at form, with o nboard VGA, AC97 audio, GIGA LAN interface. Based on the AMD Geode LX800 pr ocessor, the board provides many advanced feat ures for reduc ed power consumption, fan-less design and hig ...
-
AMD LE-366 - page 8
LE-366 User ’ s Manual - 7 - 1.2 <Product Specification> General Specification Form Factor 145 mm x 102 mm (5.7” x 4”) CPU Up to AMD Geode LX 800 Processor Memory One So-DIMM slot s upport DDR 266/333/400 MHz SDRAM up to 1GB Chipset AMD Geode CS5536 BIOS Phoenix-Award 4Mb PnP Flash Green Function ACPI 1.0 and APM 1.2 compliant Watchdog ...
-
AMD LE-366 - page 9
LE-366 User ’ s Manual - 8 - Connector External Audio phone jack for Line-out and MIC-in. Onboard audio connector with pin header Expansiv e Interface PCI 1 Mini-PCI slot V2.2 33/66 MHz 1 Compact Flash (optional) Pow er and Environment Power Requirement 12V DC Jack power connector Temperature Operating temperature with 0 ℃ ~6 0 ℃ (32 ℉ ~ 14 ...
-
AMD LE-366 - page 10
LE-366 User ’ s Manual - 9 - 1.3 <Mechanical Drawing> ‘ ‘ ‘ ‘ ‘ ‘ ...
-
AMD LE-366 - page 11
LE-366 User ’ s Manual -10- 1.4 <Block Diagram> Flash BIOS (SST FW H) 16Mbx16 DDR DIMM MiniPCI SLOT IDE X 1 CFD X 1 4 x USB2.0 port s 83627HF PCI BUS/33Mhz AMD Geode LX Processo r AM D Ge od e CS5536 CRT COM1 KB & MS Digit al I/O Slim FDD COM2 RealT ek RTL81 10SB LAN1 AL C203 A UDIO JACK LV D S ...
-
AMD LE-366 - page 12
LE-366 User ’ s Manual - 11 - Chapter 2 <Hardware Setup> 2.1<Connector Location> P1 CN1 J8 CN9 P2 CN4 JP2 JP3 CN7 USB2 USB1 LAN1 FDD1 MPCI1 CN8 CN3 J4 J P 1 C N 2 J 7 J 6 M I C 1 J S P K 1 L A N 1 U S B 1 P S 2 C O M V G A M I C L I N E O U T ...
-
AMD LE-366 - page 13
LE-366 User ’ s Manual -12- <Jumper Reference> Jumper Function JP1 L VDS Panel V oltage Selection (+5V / + 3.3V) JP2 COM2 RS232/422/485 Select JP3 COM2 RS232/422/485 Select J4 Clear CMOS Selection J7 CFD Master/Slave Selection JP2 JP3 RS-232 RS-485 RS-422 JP3 JP2 J4 J7 JP1 5 6 1 2 1 3 10 12 ...
-
AMD LE-366 - page 14
LE-366 User ’ s Manual - 13 - 2.1.1 <Connector Reference> Connector Function Remark CN1 VGA Display / Audio Connector S tandard CN2 Front Audio Connector L VDS Connector Slim CN3 Front Panel Connector Slim CN4 COM2 RS-232 / RS-422 / RS-485 Connector S tandard CN7 PS2 Keyboard / Mouse Connector Standard CN8 GPIO Connector Standard CN9 SYSTEM ...
-
AMD LE-366 - page 15
LE-366 User ’ s Manual - 14 - 2.2 <CPU and Memory Setup> 2.2.1 <CPU Setup> The board integrates AMD Geode LX800 500MHz processor w ith special d esign for power appliance. It requires onl y 3.8W power consumption at most, and is totally designed for fan-less system. 2.2.2 <Memory Setup> The board supports one 200- pin DDR266/333 ...
-
AMD LE-366 - page 16
LE-366 User ’ s Manual - 15 - 2.5 <CMOS Setup> The board’s data of CMOS can be setting in BIOS. If the board refus es to boot due to inappropriate CMOS setting s, here is how to proceed to clear (r eset) the CMOS to its default values. Jumper: J4 T ype: Onboard 3-pin jumper J4 Mode 1-2 Normal Operation 2-3 Clear CMOS Default setting Jumpe ...
-
AMD LE-366 - page 17
LE-366 User ’ s Manual -16- 2.3 <Enhanced IDE & CF Interface> The board has one Ultra DMA33 IDE interf ace to support up to 2 A T API devices, and o ne Compact Flash Ty pe II socket on the solder side. CF ...
-
AMD LE-366 - page 18
LE-366 User ’ s Manual - 17 - 2.4 <Floppy Port> The board provides a slim type floppy port; pleas e use the 26-pin FPC cable in the package to connect the floppy device. FDD 4. Lif t up this plastic bar 5. Slot the cable in (Blue p aste for outside) 6. Press back the plastic bar Floppy rear side 1. Lif t up the brow n plastic bar 2. Slot th ...
-
AMD LE-366 - page 19
LE-366 User ’ s Manual -18- 2.8 <Onboard Display Interface> The board integrates AMD Geode LX800 processor wi th built-in 2D video e ngine, to provide onboard DB15 VGA connector , 18-bit L VDS interf ace. The built-in 2D video engine supports following specified functions: ● High-performance 2D graphics controller ● Alpha BLT ● Integr ...
-
AMD LE-366 - page 20
LE-366 User ’ s Manual - 19 - 2.4.2 <Digit al Display > The board provides one 30-pin LVDS connector for 18-bit single c hannel panel, supports up to 1024 x 768 of resolution, with one LCD backlight inverter connector and one jumper for panel voltage setting Connector: JP1 Type: 3-pin Power select Header Pin Description 1 VCC (5V) 2 LCDVCC ...
-
AMD LE-366 - page 21
LE-366 User ’ s Manual -20- Connector: CN_LVDS (CN2) (for 18 bit Single channel LVDS pane l) Type: 30-pin header (15 x 2 pitch 2.0 mm) Connector model: Hirose DF13-40DP-1.25V Pin Assignment Pin Assignment 1 BKL_EN 2 BKL_CTL 3 LVDS_VCC 4 GND 5 LVDS_CH1_CLK- 6 LVDS_CH1_CLK+ 7 LVDS_VCC 8 GND 9 LVDS_CH1_DATA0- 10 LVDS_CH1_DATA0+ 11 LVDS_CH1_DATA1- 12 ...
-
AMD LE-366 - page 22
LE-366 User ’ s Manual - 21 - To setup the LCD, y ou need the component below: 1. A panel with LVDS interfaces. 2. An inverter for panel’s backlight power. 3. A LCD cable and an inverter cable. For the cables, pleas e follow the pin assignment of the connector to make a cabl e, because every panel has it s ow n pin assignmen t, so w e do not pr ...
-
AMD LE-366 - page 23
LE-366 User ’ s Manual -22- After setup the devices w ell, you need to select the LCD panel type in the BIOS. The panel type mapping is list below : Panel Number Resolution 1 640 x 480 2 800 x 600 3 1024x 768 ...
-
AMD LE-366 - page 24
LE-366 User ’ s Manual - 23 - <USB2.0 Interface> Based on AMD CS5536, the board provi des 2 x USB2.0 ports. The USB2.0 interface provides up to 480Mbps of transferring rate. Interface USB2.0 Controller CS5536 T ransfer Rate Up to 480Mb/s Output V oltage 500mA USB ...
-
AMD LE-366 - page 25
LE-366 User ’ s Manual -24- 2.5 <GPIO Interface> The board provides a programmable 8-bit digita l I/O interface; you can use this general purpose I/O port for system control like POS or KIOSK. Connector: CN8 Type: onboard 2 x 6-pin header, pitch=2.0mm Pin Assignment 1 GPI 2 GPO 3 GPI 4 GPO 5 GPI 6 GPO 7 GPI 8 GPO 9 5V 10 GND CN8 ...
-
AMD LE-366 - page 26
LE-366 User ’ s Manual - 25 - 2.6 <Serial Port Jumper Setting > The COM1 RS232 serial port, with jumper selectable RS232/422/485 for CN_COM2 Connector: COM1 Type: 9-pin Dip male connector on I/O Panel Pin Assignment Pin Assignment 1 DCD1# 2 RXD1 3 TXD1 4 DTR1# 5 GND 6 DSR1# 7 RTS1# 8 CTS1# 9 RI1# COM1 ...
-
AMD LE-366 - page 27
LE-366 User ’ s Manual - 26 - 2.7 <Power and Fan Connector> The LE-366 provides a standard A T X power supply with 20-pin A T X connector , and the board provides one 4-p in P4 additional use power connect or for internal power supply and one 3-pin cooler fan connector for system. 2.6.1 <Pow er Input> Connector: AT X Type: 20-pin ATX ...
-
AMD LE-366 - page 28
LE-366 User ’ s Manual - 27 - 2.7.3 <Fan Connector> Connector: SYSFAN Type: 3-pin fan wafer connector Connector: DC_IN Type: 2-pin DC power connector Pin Descrip tion Pin Description 1 +12V 2 +12V 3 Ground 4 Ground Pin Description Pin Description Pin Description 1 Ground 2 +12V 3 Fan Control SYSF AN ...
-
AMD LE-366 - page 29
LE-366 User ’ s Manual - 28 - 2.8 <Indicator and Switch> The JFRNT provides front con trol panel of the boa rd, such as power button, rese t and beeper , etc. Please check well before y ou connecting the cables on the chassis. Connector: CN3 Type: onboard 14-pin (2 x 7) 2.54-pitch header Pin Assignment Pin Assignment 1 GND 2 Power Switch 3 ...
-
AMD LE-366 - page 30
LE-366 User ’ s Manual - 29 - (This Page is Left For Blank) ...
-
AMD LE-366 - page 31
LE-366 User ’ s Manual - 30 - Chapter 3 <BIOS Setup> The motherboard uses the Award BIOS for the s y stem configur ation. The Award BIOS in the single board comp uter is a customized ve rsion of the in dustrial standard BIOS for IBM PC AT-compatible computers. It supports Inte l x86 and com patible CPU architecture based processors and comp ...
-
AMD LE-366 - page 32
LE-366 User ’ s Manual - 31 - (This Page is Left for Blank) ...
-
AMD LE-366 - page 33
LE-366 User ’ s Manual -32- Appendix A <I/O Port Pin Assignment> A.1 <IDE Port> Connector: J6 Type: 44-pin (22 x 2) box header Pin Assignment Pin A ssignment 1 IDERST# 2 GND 3 PID7 4 PID8 5 PID6 6 PID9 7 PID5 8 PID10 9 PID4 10 PID11 11 PID3 12 PID12 13 PID2 14 PID13 15 PID1 16 PID14 17 PID0 18 PID15 19 GND 20 N/C 21 PDREQ 22 GND 23 PI ...
-
AMD LE-366 - page 34
LE-366 User ’ s Manual - 33 - A.2 <Floppy Port> Connector: FDD1 Type: 26-pin connector Pin Assignment Pin Assignment 1 VCC 2 INDEX# 3 VCC 4 DRV_SEL# 5 VCC 6 DSK_CH# 7 N/C 8 N/C 9 N/C 10 MOTOR# 11 N/C 12 DIR# 13 DENSEL# 14 STEP# 15 GND 16 WDATA# 17 GND 18 WGATE# 19 GND 20 TRACK# 21 GND 22 WOROT# 23 GND 24 RDATA# 25 GND 26 SIDE# A.3 <Seria ...
-
AMD LE-366 - page 35
LE-366 User ’ s Manual -34- A.4 <CRT Port> Connector: CRT Type: 15-pin D-sub female connector on I/O Panel Pin Descriptio n Pin Description Pin Description 1 RED 6 Ground 11 N/C 2 GREEN 7 Ground 12 CRT_DDCDATA 3 BLUE 8 Ground 13 HSYNC 4 N/C 9 VGA_VCC 14 VSYNC 5 Ground 10 Ground 15 CRT_DDCCLK A.5 <LAN Port> Connector: RJ45 Type: RJ45 c ...
-
AMD LE-366 - page 36
LE-366 User ’ s Manual - 35 - A.7 <PS/2 Keyboard & Mouse Port> Connector: Mouse / Keyboard Type: 6-pin Mini-DIN connector on bracket Pin A ssignment Pin Assignment 1 KB_DATA 2 MS_DATA 3 GND 4 KB_VCC 5 KB_CLK 6 MS_CLK 5 6 3 4 1 2 ...
-
AMD LE-366 - page 37
LE-366 User ’ s Manual - 36 - (This Page is Left for Blank) ...
-
AMD LE-366 - page 38
LE-366User ’ s Manual - 37 - Appendix B <Flash BIOS> B.1 BIOS Auto Flash T ool The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below : TU ht tp :// www.a ward .c om UT File name of the tool is “aw d flash.exe”, it’s the utility that can writ e the ...
-
AMD LE-366 - page 39
LE-366 User ’ s Manual -38- Appendix C <System Resources> C1. <I/O Port Address Map> ...
-
AMD LE-366 - page 40
LE-366 User ’ s Manual - 39 - ...
-
AMD LE-366 - page 41
LE-366 User ’ s Manual -40- C2. <Memory Address Map> ...
-
AMD LE-366 - page 42
LE-366 User ’ s Manual - 41 - C3. <System IRQ Resources> ...
-
AMD LE-366 - page 43
LE-366 User ’ s Manual -42- Appendix D <Programming GPIO’s> The GPIO can be programmed with the MSDOS debug program using simple IN/OUT com mands. The following lines show an example how to do this. GPIO0...GPIO7 bit0……bit7 -o 4E 87 ;enter configuration -o 4E 87 -o 4E 2A - o 4 F F D ; e n a b l e G P I O f u n c t i o n -o 4E 07 -o 4F ...
-
AMD LE-366 - page 44
LE-366 User ’ s Manual - 43 - Appendix E <W atch Dog timer Setting > The watchdog timer makes the system auto-reset w h ile it stop s to work for a period. T he integrated watchdog timer can be setup as sy stem reset mode by program. Timeout Value Range - 1 to 255 - Second or Minute Program Sample Watchdog timer setup as system reset w ith ...
-
AMD LE-366 - page 45
LE-366 User ’ s Manual -44- (This Page is Left for Blank) ...
У вас вопрос, касающийся AMD LE-366?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с AMD LE-366, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с AMD LE-366 со всей вероятностью он захочет поделиться методом ее решения.