Русский dropdown-ico

Инструкция обслуживания InFocus IN5122

34 страниц 1.66 mb
Скачать

Перейти на страницу of 34

Summary
  • InFocus IN5122 - page 1

    RS232 Command and Control Guide Regulatory models: W60, W61 010-0763-00 DISPERINDAG No. 0287/1.824.51/09.03 ...

  • InFocus IN5122 - page 2

    This page left blank intentionally ...

  • InFocus IN5122 - page 3

    1 Projector IN5122/IN5124 RS232 Command and Control Guide The signals listed on the following pages are used for initial setup, however the signal timings of some computer models may be different. In such a case, adjust V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b) Front porch (d) Active video (C) Data D ...

  • InFocus IN5122 - page 4

    2 Initial set signals Resolution Freq Standard DotCLK (MHz) fH (KHz) fV (Hz) H T otal (Pixels) H Res (Pixels) H Sync (Pixels) H Back Porch (Pixels) V T otal (Lines) V Res (Lines) V Sync (Lines) V Back Porch (Lines) C A B c a b 720x400 70 VESA-DMT 28.322 31.469 70.087 900 720 108 54 449 400 2 35 640x480 60 VESA-DMT 25.175 31.469 59.940 800 640 96 48 ...

  • InFocus IN5122 - page 5

    3 Resolution Freq Standard DotCLK (MHz) fH (KHz) fV (Hz) H T otal (Pixels) H Res (Pixels) H Sync (Pixels) H Back Porch (Pixels) V T otal (Lines) V Res (Lines) V Sync (Lines) V Back Porch (Lines) C A B c a b 720x400 70 VESA-DMT 28.322 31.469 70.087 900 720 108 54 449 400 2 35 640x480 60 VESA-DMT 25.175 31.469 59.940 800 640 96 48 525 480 2 33 640x48 ...

  • InFocus IN5122 - page 6

    4 A COMPUTER IN1, B MONITOR OUT D-sub 15pin mini shrink jack <Computer signal> • Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) • H/V . sync. signal: TTL level (positive/negative) • Composite sync. signal: TTL level <Component video signal> • Video signal: - Y, Analog, 1.0±0.1Vp-p with composite sync, 7 ...

  • InFocus IN5122 - page 7

    5 E S-VIDEO Mini DIN 4pin jack • System: NTSC, P AL, SECAM, P AL-M, P AL-N, NTSC4.43, P AL(60Hz) Pin Signal 1 Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator Color signal 0.300Vp-p (P AL/SECAM, burst) 75Ω terminator 2 Brightness signal, 1.0Vp-p, 75Ω terminator 3 Ground 4 Ground Connection to the por ts (continued) 4 3 2 1 F VIDEO RCA jack ...

  • InFocus IN5122 - page 8

    6 Connection to the por ts (continued) H AUDIO IN1, I AUDIO IN2 Ø3.5 stereo mini jack • 200 mV rms, 47kΩ terminator J AUDIO IN3 (R, L) K AUDIO OUT (R, L) RCA jack x2 RCA jack x2 • 200 mV rms, 47kΩ terminator • 200 mV rms, 1kΩ output impedance L MIC Ø3.5 mono mini jack <Low level> • 2 mV rms, 1kΩ terminator <High level> ...

  • InFocus IN5122 - page 9

    7 Connection to the por ts (continued) O USB TYPE B USB B type jack Pin Signal 1 +5V 2 - Data 3 + Data 4 Ground 4 3 1 2 P CONTROL D-sub 9pin plug • About the details of RS-232 communication, please refer to the section "RS-232 Communication". Pin Signal Pin Signal Pin Signal 1 (No connection) 4 (No connection) 7 RTS 2 RD 5 Ground 8 CTS ...

  • InFocus IN5122 - page 10

    8 SCART T o input SCART RGB signal; ex. Connection to the por ts (continued) T o input SCART RGB signal to the projector , use a SCART to RCA cable. Connect the plugs refer to above example. For more reference, please consult your dealer . SCART connector (jack) SCART cable (plug) RCA plugs ...

  • InFocus IN5122 - page 11

    9 CD (1) (1) -- RD(2) (2) RD TD (3) (3) TD DTR (4) (4) -- GND (5) (5) GND DSR (6) (6) -- R TS (7) (7) R TS DTS (8) (8) CTS RI (9) (9) -- RS-232 Communication RS-232 Communication When the projector connects to the computer by RS-232 communication, the projector can be controlled with RS-232 commands from the computer . For details of RS-232 command ...

  • InFocus IN5122 - page 12

    10 Command Control via the Network When the projector is connected to the network, the projector can be controlled with RS-232 commands from the computer with a web browser . For RS-232 command information, refer to the RS-232 Communication / Network command table ( & 16 ). Connection 1. T urn of f the projector and the computer . 2. Connect th ...

  • InFocus IN5122 - page 13

    11 Communication P or t The following port is assigned for command control. TCP #23 Congure the following items from a web browser when command control is used. Port Settings Network Control Port1 (Port: 23) Port open Click the [Enable] check box to open [Network Control Port1 (Port: 23)] to use TCP #23. Default setting is “Enable”. Authenti ...

  • InFocus IN5122 - page 14

    12 Command Control via the Networ k (continued) RS-232 Commands IMPORT ANT : When formatting commands sent from a control system or computer , enclose commands in parentheses “(“ and “)”. When entering custom commands into Scheduled T asks in the projector ’s web interface, enclose commands in less than/ greater than symbols “<” an ...

  • InFocus IN5122 - page 15

    13 Command Control via the Networ k (continued) A write request example: (AAA####) where (starts the command AAA denotes the command #### denotes the value to be written (leading zeros not necessary) ) ends the command Some commands have ranges, while others are absolute. If a number greater than the maximum range is received, it is automatically s ...

  • InFocus IN5122 - page 16

    14 This projector is equipped with NETWORK BRIDGE function. When the projector connects to the computer by LAN communicaton, an external device that is connected with this projector by RS-232 communication can be controlled from the computer as a network terminal. For details, see the 6. Network Bridge function in the Network Guide . Connection 1. ...

  • InFocus IN5122 - page 17

    15 Communication settings For communication setting, use the OPTION - SERVICE - COMMUNICA TION menu. ( & OPTION menu - SERVICE - COMMUNICA TION in the User's Manual ) Item Condition BAUD RA TE 4800bps / 9600bps / 19200bps / 38400bps Data length 8 bit (xed) P ARITY NONE/ODD/EVEN Start bit 1 bit (xed) Stop bit 1 bit (xed) T ransmiss ...

  • InFocus IN5122 - page 18

    16 RS-232 Communication / Network command table RS-232 Communication / Netw ork command ta ble Function Command RW Min Max Default Step BASIC MENU Aspect Ratio 0: Auto 1: Native (IN5124 only) 2: 4:3 3: 16:9 6: 16:10 ARZ RW 0 6 0 Auto Keystone Execute 1: Execute AV K W 0 1 n/a Horizontal Keystone DKH RW 38 218 128 1 V ertical Keystone DKV RW 38 218 ...

  • InFocus IN5122 - page 19

    RS-232 Communication / Netw ork command ta ble (continued) 17 (continued on next page) Function Command RW Min Max Default Step Presets 1: User 5: Presentation 7: Video 10: Bright 1 1: Whiteboard 12: Blackboard 13: Greenboard 15: Dynamic PST RW 1 15 5 (Computer in 1) 5 (Computer in 2) 5 (LAN) 5 (USB T ype A) 5 (USB T ype B) 15 (HDMI) 15 (Component) ...

  • InFocus IN5122 - page 20

    RS-232 Communication / Netw ork command ta ble (continued) 18 (continued on next page) Function Command RW Min Max Default Step Gamma 32: 1 Default 16: 1 Custom 33: 2 Default 17: 2 Custom 34: 3 Default 18: 3 Custom 35: 4 Default 19: 4 Custom 36: 5 Default 20: 5 Custom 37: 6 Default 21: 6 Custom GTB RW 16 37 32 (Computer in 1) 32 (Computer in 2) 32 ...

  • InFocus IN5122 - page 21

    RS-232 Communication / Netw ork command ta ble (continued) 19 (continued on next page) Function Command RW Min Max Default Step Gamma Custom-4 Point 7 G41 RW 11 2 144 128 1 Gamma Custom-4 Point 8 G42 RW 11 2 144 128 1 Gamma Custom-5 Point 1 G43 RW 11 2 144 128 1 Gamma Custom-5 Point 2 G44 RW 11 2 144 128 1 Gamma Custom-5 Point 3 G45 RW 11 2 144 128 ...

  • InFocus IN5122 - page 22

    RS-232 Communication / Netw ork command ta ble (continued) 20 (continued on next page) Function Command RW Min Max Default Step Color T emperature - 6 Blue Gain BG6 RW 96 160 128 1 Color T emperature - 1 Red Offset RF1 RW 96 160 128 1 Color T emperature - 2 Red Offset RF2 RW 96 160 128 1 Color T emperature - 3 Red Offset RF3 RW 96 160 128 1 Color T ...

  • InFocus IN5122 - page 23

    RS-232 Communication / Netw ork command ta ble (continued) 21 (continued on next page) Function Command RW Min Max Default Step ADV ANCED MENU: IMAGE Aspect Ratio 0: Auto 1: Native (IN5124 Only) 2: 4:3 3: 16:9 6: 16:10 ARZ RW 0 6 0 Overscan 0: Off 1: Zoom 2: Crop OVS RW 0 2 0 V ertical Position VPS RW if def<128: 0 else: def -128 def +128 auto 1 ...

  • InFocus IN5122 - page 24

    RS-232 Communication / Netw ork command ta ble (continued) 22 (continued on next page) Function Command RW Min Max Default Step S-Video Standard 0: Auto 1: NTSC 2: P AL 3: SECAM 4: NTSC4.43 5: M-P AL 6: N-P AL ? RW 0 6 0 HDMI Format 0: Auto 1: Video 2: Computer RW 0 2 0 HDMI Range 0: Normal 1: Enhanced 16: Auto RW 0 16 16 Component 0: Component 1: ...

  • InFocus IN5122 - page 25

    RS-232 Communication / Netw ork command ta ble (continued) 23 (continued on next page) Function Command RW Min Max Default Step Corner Correction all corners Reset 0: n/a 1: enable CNR RW 0 1 n/a Side Correction Left Gain SC1 RW 98 158 128 1 Side Correction Right Gain SC2 RW 98 158 128 1 Side Correction V Position SC3 RW 0 768 (IN5122) 800 (IN5124) ...

  • InFocus IN5122 - page 26

    RS-232 Communication / Netw ork command ta ble (continued) 24 (continued on next page) Function Command RW Min Max Default Step Monitor Out for Source 5 (HDMI) 1: Computer in 1 2: Computer in 2 255: Off SM5 RW 1 255 1 Monitor Out for Source 6 (Component) 1: Computer in 1 2: Computer in 2 255: Off SM6 RW 1 255 1 Monitor Out for Source 7 (S-Video) 1: ...

  • InFocus IN5122 - page 27

    RS-232 Communication / Netw ork command ta ble (continued) 25 (continued on next page) Function Command RW Min Max Default Step Audio for Source 0 (Computer in 1) 0: Audio 1 1: Audio 2 2: Audio 3 5: Mute SA0 RW 0 5 0 Audio for Source 1 (Computer in 2) 0: Audio 1 1: Audio 2 2: Audio 3 5: Mute SA1 RW 0 5 1 Audio for Source 2 (LAN) 0: Audio 1 1: Audio ...

  • InFocus IN5122 - page 28

    RS-232 Communication / Netw ork command ta ble (continued) 26 (continued on next page) Function Command RW Min Max Default Step HDMI Noise Cancel 0: Disable 1: Enable HNC RW 0 1 1 MIC Level 0: Low 1: High MIK RW 0 1 0 MIC V olume MIC RW 0 48 24 1 ADV ANCED MENU: SCREEN Menu Positon H OFH RW 0 10 0 (left) 1 Menu Positon V OFV RW 0 10 10 (top) 1 Blan ...

  • InFocus IN5122 - page 29

    RS-232 Communication / Netw ork command ta ble (continued) 27 (continued on next page) Function Command RW Min Max Default Step RS-232 Communication / Netw ork command ta ble (continued) Auto Power 0: Disable 1: Enable AOT RW 0 1 0 USB T ype B 0: Mouse 1: USB Display USB RW 0 1 1 Custom Key (Effect) 0: Blank 1: Mute 2: Aspect Ratio 3: Source 4: Aut ...

  • InFocus IN5122 - page 30

    RS-232 Communication / Netw ork command ta ble (continued) 28 (continued on next page) Function Command RW Min Max Default Step RS-232 Communication / Netw ork command ta ble (continued) Source 4 0: Computer in 1 1: Computer in 2 2: LAN 3: USB T ype A 4: USB T ype B 5: HDMI 6: Component 7: S-Video 8: Video SR4 RW 0 8 8 Power-up Source 0: Computer i ...

  • InFocus IN5122 - page 31

    RS-232 Communication / Netw ork command ta ble (continued) 29 (continued on next page) Function Command RW Min Max Default Step My Image Display 0: Off 1: Image-1 2: Image-2 3: Image-3 4: Image-4 MIF RW 0 4 0 My Image Delete Image-1 1: delete MD1 W 0 1 n/a My Image Delete Image-2 1: delete MD2 W 0 1 n/a My Image Delete Image-3 1: delete MD3 W 0 1 n ...

  • InFocus IN5122 - page 32

    RS-232 Communication / Netw ork command ta ble (continued) 30 (continued on next page) Function Command RW Min Max Default Step Freeze 0: Off 1: On FRZ RW 0 1 0 INFOCUS UNIQUE About (Source Info) 0: n/a 1: enable ABT W 0 1 n/a Lamp Lit 0: not lit 1: lit LML R 0 1 0 Number of Lamp Resets LMR R 0 32766 0 Lamp T otal On T ime (All Bulbs) LMT R 0 21474 ...

  • InFocus IN5122 - page 33

    31 PJLink command PJLink command POWR Power Control 0 = Standby 1 = Power On POWR ? Power Status inquiry 0 = Standby 1 = Power On 2 = Cool Down INPT Input Source selection 1 1 = COMPUTER IN 1 12 = COMPUTER IN 2 21 = COMPONENT 22 = S-VIDEO 23 = VIDEO 31 = HDMI 41 = USB TYPE A 51 = LAN 52 = USB TYPE B INPT ? Input Source inquiry 1 1 = COMPUTER IN 1 1 ...

  • InFocus IN5122 - page 34

    32 PJLink command (continued) Commands Control Description Parameter or Response ERST ? Error Status inquiry 1st byte: Refers to Fan error; one of 0 to 2 2nd byte : Refers to Lamp error; one of 0 to 2 3rd byte: Refers to T emperature error; one of 0 to 2 4th byte: Refers to Cover error; one of 0 to 2 5th byte: Refers to Filter error; one of 0 to 2 ...

Производитель InFocus Категория Projector

Документы, которые мы получаем от производителя устройства InFocus IN5122 мы можем разделить на несколько групп. Это в частности:
- технические чертежи InFocus
- инструкции обслуживания IN5122
- паспорта изделия InFocus
- информационные брошюры
- энергетические этикетки InFocus IN5122
Все из них важны, однако самую важную информацию с точки зрения пользователя мы найдем в инструкции обслуживания InFocus IN5122.

Группа документов, определяемая как инструкции обслуживания, делится также на более подробные типы, такие как: Инструкции монтажа InFocus IN5122, инструкции обслуживания, короткие инструкции или инструкции пользователя InFocus IN5122. В зависимости от потребностей, Вам необходимо поискать требуемый документ. На нашем сайте Вы можете просмотреть самую популярную инструкцию использования изделия InFocus IN5122.

Похожие инструкции обслуживания

Полная инструкция обслуживания устройства InFocus IN5122, как должна выглядеть?
Инструкция обслуживания, определяемая также как пособие пользователя, или просто "руководство" - это технический документ, цель которого заключается в использовании InFocus IN5122 пользователями. Инструкции пишет, как правило технический писатель, языком, доступным для всех пользователей InFocus IN5122.

Полная инструкция обслуживания InFocus, должна заключать несколько основных элементов. Часть из них менее важная, как например: обложка / титульный лист или авторские страницы. Однако остальная часть, должна дать нам важную с точки зрения пользователя информацию.

1. Вступление и рекомендации, как пользоваться инструкцией InFocus IN5122 - В начале каждой инструкции, необходимо найти указания, как пользоваться данным пособием. Здесь должна находится информация, касающаяся местонахождения содержания InFocus IN5122, FAQ и самых распространенных проблем - то есть мест, которые чаще всего ищут пользователи в каждой инструкции обслуживания
2. Содержание - индекс всех советов, касающихся InFocus IN5122, которое найдем в данном документе
3. Советы по использованию основных функций устройства InFocus IN5122 - которые должны облегчить нам первые шаги во время использования InFocus IN5122
4. Troubleshooting - систематизированный ряд действия, который поможет нам диагностировать а в дальнейшем очередность решения важнейших проблем InFocus IN5122
5. FAQ - чаще всего задаваемые вопросы
6. Контактные данные Информация о том, где искать контактные данные производителя / сервисного центра InFocus IN5122 в данной стране, если самостоятельно не получится решить проблему.

У вас вопрос, касающийся InFocus IN5122?

Воспользуйтесь формуляром, находящимся ниже

Если с помощью найденной инструкции Вы не решили свою проблему с InFocus IN5122, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с InFocus IN5122 со всей вероятностью он захочет поделиться методом ее решения.

Перепишите текст с картинки

Captcha
Новая картинка

Комментарии (0)