-
Powermatic 4224 - page 1
Operating Instructions and Parts Manual 24” Wood Lathe Model: 4224 WMH T ool Group 2420 Vantage Drive Elgin, Illinois 60123 Part Number: M-0460228 Phone: 800-274-6848 Revision B 11/03 www.wm ht oo lg r oup.com Copyright © WMH Tool Group ...
-
Powermatic 4224 - page 2
2 This manual has been prepared for the owner and operator s of a Powermatic Model 4224 24” Wood Lathe. Its purpose, aside from machine operation, is to promote safety using accepted operating and maintenance procedures. To obtain maximum life and efficiency from your wood lathe, and to aid in using the machine safely, read this manual thoroughly ...
-
Powermatic 4224 - page 3
3 TABLE OF CONTENTS Safety Rules ................................................................................................................... ............................ 4-5 Safety: Decals ................................................................................................................. .............................. 6 Specif ...
-
Powermatic 4224 - page 4
4 1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. This wood lathe is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a wood lathe, do not use it until the proper training and knowledge have been obtained. 3. ...
-
Powermatic 4224 - page 5
5 SPEED RECOMMENDATIONS Dia met er of Wor k Roughing RPM G ener al Cutt i ng RPM Fi ni shi ng RPM U n der 2 " 1500 3000 3000 2 t o 4" 600 1500 2300 4 t o 6" 450 1 100 1500 6 t o 8" 450 600 1 100 8 t o 10" 450 600 850 10 to 12" 450 600 850 12 to 14" 450 450 600 26. When sanding, remove the tool rest from the mach i ...
-
Powermatic 4224 - page 6
6 ! SAFETY: DECALS Familiarize yourself with the location and content of this decal on your machine. 6294773 ...
-
Powermatic 4224 - page 7
7 SPECIFICATIONS: 4224 Lathe Distance Betw een Cent ers ....................................................................................................... ............................. 42" Swing Over Bed ................................................................................................................. ...................... ...
-
Powermatic 4224 - page 8
8 RECEIVING Remove the lathe from the shipping container and check for damage. Report any damage to your distributor immediately. Accessories are packaged in a separate carton which will be on the shelf of the machine stand. Clean protecti ve coating from the bed, spindles, work rest and face plate with kerosene or a good commercial solvent. Read t ...
-
Powermatic 4224 - page 9
9 Tool Support The tool support (shown in Figure 5), is designed to allow adjustment for height, position on the bed, and angle to the work. Your 4224 lathe comes standard with the 14" tool support. Other supports are available; consult the "Optional Equipment" list on page 24. Periodically the tool rest should be disassembled and th ...
-
Powermatic 4224 - page 10
10 TOOLS If possible, select only quality, high speed steel turni ng tools. High speed tools hol d an edge and last longer than ordinary carbon steel. As one becomes proficient in turning, a variety of specialty tools for specific applications can be acquired. The following tools provide t he basics for most woodturning projects: Large Roughing Gou ...
-
Powermatic 4224 - page 11
11 FIGURE 2 STOCK SELECTION Stock for spindles should be straight grained and free of checks, cracks, knots and other defects. It should be cut 1/8" to 1/4" larger than the finished diameter and may r equire additional length to remove ends if required. Larger stock should have the corners removed to produce an oct agon making the piece e ...
-
Powermatic 4224 - page 12
12 ROUGHING OUT: 1. Begin with a large roughing gouge. Place the tool on the t ool support with the heel of the tool on the surface to be cut. 2. Slowly and gently raise tool handle until cutting edge comes into contact with the workpiece. 3. Beginning at the tailstock end of the workpiece, roll the flute (hollowed-out portion) of the tool in the d ...
-
Powermatic 4224 - page 13
13 PARTING OFF: 1. Use parting tool. 2. Adjust lathe speed to lower RPM for parting through a workpiece. 3. Place tool on tool support and raise the handle until it starts to cut and continue to cut towards the center of the workpiece. 4. Loosely hold on to the piece in one hand as it separates from the waste wood. SANDING and FINISHING: Leaving cl ...
-
Powermatic 4224 - page 14
14 there are dozens of chucks to choose from , the woodturner should first consider a ll the different types of turning that will be done, and read reports or discuss with other turner s who own chucks before making a decision. A chuck is not a requirement but is handy when working on more than one piece at a time. Rather than removing screws, you ...
-
Powermatic 4224 - page 15
15 10. Stop the lathe, remove workpiece and attach face plate or chuck (see "Mounting Stock" above). 11. Finish turning the outside of bowl with 1/2" or 3/8" bowl gouge. Leave additional material at base of bowl for support while turning interior. This will be removed later. TO SHAPE INTERIOR OF BOWL: 1. Stop lathe and move tail ...
-
Powermatic 4224 - page 16
16 TROUBLE-SHOOTING (4224 Lathe) PROBLEM POSSIBLE CAUSE SOLUTION Excessive vibration. 1. Defective spindle bearings. 1. Replace bearings. 2. Worm or defective belt. 2. Replace belt. 3. Defective motor. 3. Replace motor. 4. Workpiece warped, out-of-r ound, 4. Correct problem by planing has major flaw, or was improperly or sawing, or scrap workpiece. ...
-
Powermatic 4224 - page 17
17 ELECTRICAL SCHEMATIC: 4224 Lathe ...
-
Powermatic 4224 - page 18
18 PARTS LIST: Stand & Bed Assembly (4224 Lathe) No. Part No. Description Quantity 1 6294742 Tool Support, 14" .................................................................................................... .... 1 2 6294753 Tool Support Assembly (Items 3 thru 10, 14, 15, 36, 37)........................................... 1 3 6295851 T ...
-
Powermatic 4224 - page 19
19 PARTS LIST: Stand & Bed Assembly (4224 Lathe) continued No. Part No. Description Quantity 6294733 Remote ON/OFF Switch Assembly (Items 65, 66, 68, 70, 71) ................................... 1 65 6295760 On/Off Swit ch ....................................................................................................... ....... 1 66 6295761 ...
-
Powermatic 4224 - page 20
20 Stand & Bed Assembly (4224 Lathe) ...
-
Powermatic 4224 - page 21
21 PARTS LIST: Headstock Assembly (4224 Lathe) No. Part No. Description Quantity 1 6295785 H andwheel ............................................................................................................ .... 1 2 6295786 Nut, Lock ............................................................................................................ ... ...
-
Powermatic 4224 - page 22
22 PARTS LIST: Headstock Assembly (4224 Lathe) Continued No. Part No. Description Quantity 59 6295843 Cl amp ............................................................................................................... ......... 1 60 6295844 Nut, #10-24 .............................................................................................. ...
-
Powermatic 4224 - page 23
23 Headstock Assembly (4224 Lathe) ...
-
Powermatic 4224 - page 24
24 OPTIONAL ACCESSORIES (4224 Lathe) Part No. Description 6294730 Metal Spinning Tool Support, 12" 6294731 Tool Support, 26" 6294734 Adapter, 1-1/4" to 1-1/2" 6294739 Tool Support, 6" 6294740 Bowl Turning Tool Support (RH) 6294741 Tool Support, 16" 6294745 Ball Bearing Center 6294747 Guard Assembly 6294736 Face Plate, ...
-
Powermatic 4224 - page 25
25 65" Bed Extension Assembly (Optional - 4224 Lathe) ...
-
Powermatic 4224 - page 26
26 PARTS LIST: Outboard Turning Assembly (Optional - 4224 Lathe) No. Part No. Description Quantity 6295858 Outboard Turning Assemb ly (Items 1 thru 17) ................................................................ 1 6295845 Short Outfeed Bed Extension Asse mbly (Items 1, 5, 6, 7) .............................................. 1 6295846 Tool Rest ...
-
Powermatic 4224 - page 27
27 Outboard Turning Assembly (Optional - 4224 Lathe) To order parts or reach our serv ice department, please call our toll-free number between 7:00 a.m. and 6:00 p.m. (CST), Monday through Friday. Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. Locating the stock n ...
-
Powermatic 4224 - page 28
28 WMH Tool Group 2420 Vantage Drive Elgin, Illinois 60123 Phone:800-274-6848 www.wmhtoolgroup.com ...
У вас вопрос, касающийся Powermatic 4224?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Powermatic 4224, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Powermatic 4224 со всей вероятностью он захочет поделиться методом ее решения.