-
Wasp Bar Code WPL606 - page 1
WPL606 Thermal Label Printer User’s Guide For Wasp Technologies DT/TT Printer Copyright Wasp Bar Code Technologies 2004. All rights reserved. No part of this publication may be reproduced or transmitted in any form or by any means without the written permission of Wasp Bar Code Technologies. The information contained in this document is subje ...
-
Wasp Bar Code WPL606 - page 2
CONTENTS 1. Product Introduction 1 1.1 Specification..............................................................................................................1 1.1.1 Printer.....................................................................................................................1 1.1.2 Environment..................................... ...
-
Wasp Bar Code WPL606 - page 3
1. Product Introduction Thank you for purchasing the W606 bar code printer. This guide will describe all of the common operations needed to operate and maintain your W606. 1.1 Specification 1.1.1 Printer Item Specification Printing Mode Thermal transfer and direct thermal Resolution 203DPI Max. Print Length 1000 mm ( 39.4” ) Max. Print Width 104 ...
-
Wasp Bar Code WPL606 - page 4
1.1.4 Bar Code Code 39, Code 93, Code128 subsets A B and C, Code 11, Codabar, Interleaved 2 of 5, EAN-8, EAN-13, EAN-128, UPC-A, UPC-E, EAN, UPC, EAN 2 or 5 digit add-on, UPC 2 or 5 digit Add-on, CPOST, MSI Plessy, Postnet, EAN-14, ITF-14, PDF-417, Maxicode, DataMatrix, QR Code 1.2 Optional Items l Cutter module l Peel off sensor l Portable LCD key ...
-
Wasp Bar Code WPL606 - page 5
2. Getting Started 2.1 Unpacking and Inspection After receiving the bar code printer, carefully inspect the device and its packaging. The printer is specially packaged to withstand damage in shipping. In case of evident damage, contact the carrier directly to specify the nature and extent of damage. Please retain the packaging materials in case you ...
-
Wasp Bar Code WPL606 - page 6
Figure 2: Printer rear view Figure 3: Printer interior view External Label Feed Opening Centronics Port RS-232C Port Power Switch Power Supply Connector Print Head Lift Lever Ribbon Rewind Spindle Ribbon Supply Spindle Label Spindle Media Guide Bar Label Guide Ribbon Tension Adjustment Knob Print Head Pressure Adjustment Knob USB port ...
-
Wasp Bar Code WPL606 - page 7
2.4 Buttons, Indicators and adjustment knobs Power Indicator When the printer is in the power-on state, the Power indicator is lit. On-Line Indicator This green On-Line indicator is lit when the printer is ready. The On-Line indicator blinks when in PAUSE mode. Error Indicator The red Error indicator illuminates in the event of a printer error, suc ...
-
Wasp Bar Code WPL606 - page 8
the LCD display shows “Carriage Open” and the red Error light will come on. After closing the print head lift lever, the On-Line light will blink. Press the FEED button to re-register the label. Ribbon Tension Adjustment Knob The Ribbon Tension Adjustment Knob offers 6 levels of tension to adjust for different widths of ribbon. Turn the ribbon ...
-
Wasp Bar Code WPL606 - page 9
3. Set Up 3.1 Setting Up the Printer 1. Place the printer on a flat, secure surface 2. Make sure the POWER switch is off 3. Connect the printer to the computer with the provided RS-232C, Centronics/Parallel, or USB cable 4. Plug the power cord into the power supply connector at the rear of the printer, and then plug the power cord into a properly g ...
-
Wasp Bar Code WPL606 - page 10
Figure 6: Ribbon under Pint Had 6. Pull the paper core up to the rewind spindle and slide it on. Slide both the ribbon and rewind spindle all the way to be flush with the case side of the spindle. The Wasp logo will face up again Figure 7: Ribbon placed onto Rewind Spindle 7. Roll the rewind spindle by hand until some of the actual ribbon shows in ...
-
Wasp Bar Code WPL606 - page 11
3.3 Label Roll Installation 1. Open the printer panels and the print head lift lever 2. Rotate the Label Guide clockwise away from the Media Guide Bar 3. Insert a new label roll into the label spindle 4. Pull labels leading edge forward under the black media guide bar, through the gap/black mark sensor and place the label leading edge onto the Plat ...
-
Wasp Bar Code WPL606 - page 12
3.4 Peel-off Sensor Installation (Sold Separately) 1. Turn the printer off 2. Open the lower front panel 3. Snap the peel-off sensor onto the bar that is under the print head pressure adjustment knobs horizontally Figure 12: Peel Sensor attached to bar Figure 13: Peel Socket 4. Plug the Peel-off sensor into the socket by sliding it along the bar in ...
-
Wasp Bar Code WPL606 - page 13
3.5 Loading Label For Peel-off Mode 1. Open the front and top printer doors 2. Open the print head left lever 3. Pull several inches of labels out through the front of the printer and remove the label(s) from the backing 4. Feed the label backing between the platen roller and the silver peeler roller then press the MENU button several times to adva ...
-
Wasp Bar Code WPL606 - page 14
3.6 Self-test To initiate the self-test mode, press the MENU button to advance the selection to Printer Test. Press the EXE button to enter the submenu and press the MENU button to advance the selection to Printer Config. Press EXE button to print the printer’s internal settings. During self-test, a check pattern is used to check the performance ...
-
Wasp Bar Code WPL606 - page 15
Figure 18: Printout of dump mode ASCII Data Hex decimal data related to left column of ASCII data ...
-
Wasp Bar Code WPL606 - page 16
4. Calibration There are two power-on button combinations to initialize the printer settings and to calibrate sensors on the W606. 4.1 Printer Initialization Printer Initialization will restore printer settings to defaults. Do this if labels are printing incorrectly and all other solutions have failed to solve the problem. Default settings: Item De ...
-
Wasp Bar Code WPL606 - page 17
To initialize the printer: 1. Turn off the printer power 2. Hold down the PAUSE and FEED buttons and turn on the printer power 3. Release the buttons once the Power, On-Line, and Error lights are lit Note: The printing method, thermal transfer or direct thermal printing, will be set automatically at the activation of printer power by checking for t ...
-
Wasp Bar Code WPL606 - page 18
4.3 Troubleshooting Guide The following guide lists the most common problems that may be encountered when operating this bar code printer. If the printer still does not function after all suggested solutions have been invoked, please contact the Customer Service. Condition Reasons Solutions No ribbon 1. Out of ribbon 2. The ribbon is installed inco ...
-
Wasp Bar Code WPL606 - page 19
5. Printer Maintenance The printer should be cleaned regularly to maintain high quality printing. 5.1 Cleaning the Print Head 1. Switch off and unplug the printer 2. Open the printer cover 3. Open the print head lift lever 4. Remove the ribbon. (If loaded) 5. Rub the Wasp Thermal Printer Cleaning Pen Part# 633808441012 tip across the print head sev ...
-
Wasp Bar Code WPL606 - page 20
6. Support and Warranty 6.1 Product Support If you experience any problems with your Wasp printer that you are unable to resolve, use our online support site to register and report the problem then call for technical assistance at (214) 547-4100, Monday through Friday, 8:00 AM – 5:00 PM Central Standard Time. You must register to be eligible for ...
-
Wasp Bar Code WPL606 - page 21
Appendix 1: LCD Control Panel Operation Map 1. Print Setup 0~999 (*0) Auto. Ribbon Manual Bline Auto Bline 2. Sensor Calib. Speed Auto. Gap Cutter Batch * Tear Mode Peel On Manual Ribbon Cutter On Manual Gap Exit Reference Y Reference X Offset Density Direction Lang. 3. System Setup Simplified Chinese Polski * English Traditional Chinese Code Page ...
-
Wasp Bar Code WPL606 - page 22
Country * 8 7 * None Parity Data Bit Odd Even Baud 2 * 1 Stop Bit(s) 57600 56000 38400 19200 *9600 4800 2400 Restore Defaults Exit Avail. Memory File List 4. File Mngment DRAM: 512KB free PAUSE: Del. All FEED: Exit Delete File(s) Exit * 001 002 003 031 032 033 034 036 038 039 041 042 046 045 044 061 055 047 048 049 351 358 Print Config 5. Printer T ...
У вас вопрос, касающийся Wasp Bar Code WPL606?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Wasp Bar Code WPL606, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Wasp Bar Code WPL606 со всей вероятностью он захочет поделиться методом ее решения.