-
Smeg GD100XG - page 1
21 T able of Content s INSTRUCTIONS FOR THE USER : these pro vide recommendations for use, a description of the controls and the correct procedures for cleaning and maintaining th e app liance INSTRUCTIONS FOR THE INST ALLER : these are intended for the qualified engineer who is to install, commission and test the applian ce 1. PRECAUTIONS FOR U SE ...
-
Smeg GD100XG - page 2
22 Precautions f or Use 1. PRECA UTIONS FOR USE THIS MANU AL IS AN INTEGRAL P ART OF THE APPLIANCE. T AKE GOOD CARE OF IT AND KEEP IT T O HAND TH ROUGHOUT THE HOB'S LIFE CYCLE. WE URGE Y OU TO READ THIS MANU AL AND ALL THE INFORMA TION IT CONT AINS CAREFU LL Y BEFORE USING THE APPLIANCE. INST ALLA TION MUST BE CARRIED OUT BY QU ALIFIED ST AFF ...
-
Smeg GD100XG - page 3
23 Disposal instructions 2. DISPOSAL INSTRUCTIONS - OUR EN VIRONMENT POLICY Our products are only packaged using non-pollutant, environment-friendly , recyclable materials . We urge y ou to cooperate b y disposing of the packaging properly . Contact your local dealer or the competent local organisati ons f or the add resses of collection, recycling ...
-
Smeg GD100XG - page 4
24 Safety Precautions 3. SAFETY PRECAUTIONS SEE INST ALLA TION INSTRUCTIONS FOR SAFETY REGULA TIONS FOR ELECTRIC OR GAS APPLIANCES AND FOR VENTILA TION F UNCTIONS. IN Y OUR INTEREST AND TO ENSURE Y O UR SAFETY , BY LA W ALL ELECTRIC APPLIANCES MUST ONL Y BE INST ALLED AND SER VICED BY QU ALIFIED ST AFF , IN ACCORD ANCE WITH THE RELEV ANT REGULA T I ...
-
Smeg GD100XG - page 5
25 Instructions f or the User 4. GETTING T O KNO W Y OUR APPLIA NCE 5. BEFORE INSTALLATION A uxiliar y Bur ner (A UX) Rapid Bur ner (R) Semi-rapid (SR) b urner Ultrarapid Burner (UR3) Raised spoke pan stand Nev er l eav e packaging residues unattended in the home. Separate waste packaging materials by type and consign them to the nearest separate d ...
-
Smeg GD100XG - page 6
26 Instructions f or the User 6. USING THE HOB 6.1 Gas hob Before lighting the hob burners check that the flame diffuser rings are correctly in place with their respec tive b u rner caps, making sure that the holes A in the flame diffusers are aligned with the plugs and ther mocouples. The optional grid B is for use with w oks. T o prev ent damage ...
-
Smeg GD100XG - page 7
27 Instructions f or the User 6.2 Practical hints f or using the bu rners F or better bur ner efficiency an d to minimise ga s consumption, use pans with flat, ev en bottoms with lid and of suitable size f or the burner , so that flames do not reach up the sides of the pan (see point "6.3 P an diameters"). Once the contents come to the bo ...
-
Smeg GD100XG - page 8
28 Instructions f or the User 7. CLEANING AND MAINTENANCE NEVER USE A JET OF STEAM FOR CLEANING THE APPLIANCE. Before carrying out any operations, disconnect the appliance from the electricity supply . 7.1 Cleaning s tainless stee l T o keep stainless steel in good condition, it must be cleaned regularly , after each use of the appliance, first all ...
-
Smeg GD100XG - page 9
29 Instructions f or the Installer 8. FITTING THE APPLIANCE 8.1 Fitting the ap pliance in the top This appliance is in class 3. The procedures required below must be carried out by a skilled builder and/or joiner . The hob can be installed on various mater ials, including masonr y , metal, solid wood and wood finished with plastic lamina tes, provi ...
-
Smeg GD100XG - page 10
30 Instructions f or the Installer 8.1.2 Installation to a fl ush mounting structure Make a hole in the top of the cabine t of the size shown in the figure, lea ving a spac e " X " of at least 110 mm from the rear edg e. The underside of the casing must be fully accessible once the ap pliance has been installed. This appliance may be inst ...
-
Smeg GD100XG - page 11
31 Instructions f or the Installer This type of appli ance also requires a cut 3 mm deep in the top with the dimensions shown in figure 7 (detail A ). Bef ore fitting the hob , apply the adhesive sponge strip sup plied " B " along th e entire surface of the cut (fig. 7). Now place the 12 brack ets supplied to secure the top to the suppor ...
-
Smeg GD100XG - page 12
32 Instructions f or the Installer 8.2 Securing the ap pliance to the cabine t 8.2.1 Securing the side brac kets Fit the two provided brac kets to the shor t sides of the appli ance as shown in figura 4-5 4) 5) 8.2.2 Securing the fr ont/rear brackets The hob is eq uipped with 10 brack ets " A " (see f ig. 6) whic h secure a nd lev el it r ...
-
Smeg GD100XG - page 13
33 Instructions f or the Installer 8.3 Electrical connection Check that the pow er supply voltage and size are as specified on the nameplate below the a ppliance car t er . The nameplate must ne ver be removed. The appliance must be connected to ear th in compliance with electrical system safety regulations. If a per manent connection is used, t he ...
-
Smeg GD100XG - page 14
34 Instructions f or the Installer 9. GAS CONNECTION Before installing, chec k that the lo cal gas main (type and pre ssure) and the appliance's setting s are compatible. There are 2 ways to connect the ap pliance to the domestic gas main: 1- Make two branches with a pipe or steel hose an d unite them with a T - fitting just downline of the ga ...
-
Smeg GD100XG - page 15
35 Instructions f or the Installer 9.2 Room ventilati on The appliance may only be installed in a per manently ventilated room as specified by the relev an t regulations. The air flo w into the room where the appliance is installed must be sufficient for proper gas comb ustion and room ventilation. The air intakes , protected by gratings, must be o ...
-
Smeg GD100XG - page 16
36 Instructions f or the Installer 10. AD APTING T O DIFFERENT TYPES OF GAS Before carrying out the operations descr ibed below , disconne ct the appliance from the electr icity supply . The appliance is tested with G20 (2H) na tural gas at the pressure of 20 mbar . If it is to be used with other types of gas, the b u rner nozzles hav e to be chang ...
-
Smeg GD100XG - page 17
37 Instructions f or the Installer 10.2 Burner and Nozzle Data T ables Burner R ATED HEAT CAPACITY ( K W) LPG – G30/G31 28/37 mbar Nozzle diameter 1/100 mm By-pass mm 1/100 Reduced heat capacity (W) Net g/h G30 Net g/h G31 Au x i l i a r y ( ! ) 1.05 50 30 * 28 ** 350 76 75 Semi-rapid (2) 1.75 65 33 * 32 ** 450 127 125 Rapid (3) 2.3 75 45 * 42 ** ...
-
Smeg GD100XG - page 18
38 Instructions f or the Installer 11. FINAL OPERATIONS FOR GAS APPLIANCES After making the adjustments descr ibed above , reassemble the appliance, rev ersing the proc edures described in point "10.1 Changing the hob nozzles". After adjusting f or use of a gas other than th e gas used f or testing the appliance, replace the gas setting l ...
У вас вопрос, касающийся Smeg GD100XG?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Smeg GD100XG, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Smeg GD100XG со всей вероятностью он захочет поделиться методом ее решения.