-
CDA FW552 - page 1
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www .cda.eu FW552 Integrated Three Quarter Height Fridge Manual for Installation, Use and Maintenance ...
-
CDA FW552 - page 2
Important The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CD A reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance. This appliance is not designed to be used by people (incl ...
-
CDA FW552 - page 3
This appliance has been manufactured to the strictest standards and complies with all applicable legislation, including Electrical safety (L VD) and Electromagnetic interference compatibility (EMC). Parts intended to come into contact with food conform to EEC/89/109 .4 IMPORT ANT INFORMA TION FOR CORRECT DISPOSAL OF THE PRODUCT IN A CCORD ANCE WITH ...
-
CDA FW552 - page 4
Important Never store inflammable or explosive items and strong corrosive acids or alkalis in the appliance. This is a household appliance, which is produced in accordance with the national standard. It is intended for food storage only, not for storage of blood, medicine and biological products. To prevent risk of fire, keep the appliance away f ...
-
CDA FW552 - page 5
Before First Use You must allow the fridge to settle for at least twenty four hours prior to switching the power on. It is recommended that you clean the interior of the appliance prior to first use, using a solution of bicarbonate of soda and warm water and then thoroughly drying the interior. The fridge may have an odour to it at first use. Thi ...
-
CDA FW552 - page 6
fig. 1 Setting the T emperature You must allow the fridge to settle for at least twenty four hours prior to switching the power on. To adjust the temperature turn the thermostat control knob clockwise (from o) to the required level. The temperature becomes colder the higher the number on the control. Please note: When the thermostat is set to 0 ...
-
CDA FW552 - page 7
• Make sure food is clean and any extra water is wiped away before putting into the fridge. • Wrap or cover food before putting into the fridge. This will help prevent the loss of moisture, keep food fresh and avoid unpleasant odours. • Sort foods prior to storing. Any foods to be used soon should be stored at the front of the shelf to preven ...
-
CDA FW552 - page 8
• Avoid contact between already frozen food and food that has yet to be frozen (approx. 20 mm distance). • After 24 hours turn the thermostat knob back to the normal position. Please note: the amount of fresh food that can be frozen within 24 hours is shown on the rating plate as freezing capacity. Freezing more than this amount will aect th ...
-
CDA FW552 - page 9
Care and cleaning Always disconnect the appliance from the power supply before any cleaning or maintenance. The fridge sections should be cleaned using a solution of bicarbonate of soda and lukewarm water. Do not use abrasive products or detergents. After washing, rinse and dry thoroughly. Clean the shelves and balconies separately by hand with soa ...
-
CDA FW552 - page 10
fig. 2 Defrosting the Fridge The fridge is self-defrosting. Any water created will run out of the fridge through the channel at the back of the fridge. It is important to keep the channel clear at all times. The defrosted water is collected in the evaporating tray at the back of the appliance. Defrosting the Ice Box The ice box should be defrosted ...
-
CDA FW552 - page 11
Changing the Light Bulb Disconnect the appliance from the power. • Carefully remove the light cover by pushing in the lever at the back of the cover, and then pulling the cover down. • Unscrew the light bulb to remove it and replace with a new bulb (15W max). • Replace the light cover and reconnect the power after five minutes’ delay as ex ...
-
CDA FW552 - page 12
• The cooling system at the rear of the appliance is clean and free of dust, and not touching the rear wall. • There is enough ventilation at the side and rear walls. • The temperature of the room is adequate (10 o C or above). The appliance is noisy • The appliance is level and stable. • The side and rear walls are clear, and there is no ...
-
CDA FW552 - page 13
fig. 2 Installation Product Dimensions and aperture required for installation: Y our refrigerator is designed to be installed into a standard larder unit of width 560-570mm and depth of 550mm. the diagram below shows the product dimensions and aperture required. Note also the arrows on the diagram show ventilation requirements. In the diagram a pl ...
-
CDA FW552 - page 14
2 1 B-C fig. 5 Fig. 3 - Fitting the decor door bracket Unscrew and remove the nuts and washers from the appliance door . Place fixing bracket on the appliance door by inserting the holes to adjustment bolts. Dimension B= Measure from the underside surface of kitchen unit to the bottom of fixing bracket. Dimension C= Measure from the underside su ...
-
CDA FW552 - page 15
fig. 8 Fig. 6 - Aligning the decor door Close the door and check the alignment with the other unit doors. Adjust the decor door by screwing or unscrewing the adjustment bolts for vertical adjustment and by the help of the slots on the fixing bracket for other directions. L ock the screws into place as shown in 4. Fig. 7 - Fitting the decor door b ...
-
CDA FW552 - page 16
Fig.9 - Fitting the plinth Fit the plinth section, providing minimum 25 mm gap between the cabinet door and fix it. Never cover over the ventilation slots. Once installed the plinth must not block the ventilation slots in the appliance. This may require cutting the plinth down. Failure to ensure adequate ventilation may invalidate the warranty . ? ...
-
CDA FW552 - page 17
Reversing the Door It is possible to reverse the door on this appliance, if required. To do so, follow the steps below: 1. Open the door. 2. Remove the white hinge screw cover plate carefully to gain access to the hinge screws. 3. Loosen the hinge fixing screws (1) and remove the door. 4. Remove the door fixing screws (2). 5. Remove the cover cap ...
-
CDA FW552 - page 18
Electrical information W arning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13Amp fused plug. T o change a fuse in this type of plug, follow the steps below: 1. R emove the fuse cover and fuse. 2. Fit replacement 13A fuse, A ST A approved to BS 1362 type, into the fuse cover . 3. R eplace fuse ...
-
CDA FW552 - page 19
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: • The wire which is coloured GREEN and YELL O W must be connected to the terminal which is marked with letter (E) or by the Earth symbol or coloured GREEN and YELL O W . • The ...
-
CDA FW552 - page 20
Please contact our Customer Care Department, or for Service on the details below . Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu ...
У вас вопрос, касающийся CDA FW552?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с CDA FW552, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с CDA FW552 со всей вероятностью он захочет поделиться методом ее решения.