-
Datalogic Scanning DLL2020-WO - page 1
User's manual Datalogic DLL2020-WO ...
-
Datalogic Scanning DLL2020-WO - page 2
Copyright © 1998, Datalogic. This manual is copyrighted, with all rights reserved. Under the copyright laws, this manual may not, in whole or in part, be copied, photocopied, reproduced, translated or converted to any electronic medium or machine readable form without prior written consent of Datalogic. Limited Warranty Under all circumstances thi ...
-
Datalogic Scanning DLL2020-WO - page 3
T able of contents Preface i Chapter 1 The DLL2020-WO 1 1.1 Unpacking the DLL2020-WO 2 1.2 Scanning bar codes with the DLL2020-WO 4 1.3 Scanner labelling 7 1.4 Maintaining the scanner 11 1.5 Controlling the scanner fr om the POS system 11 Chapter 2 Installing the DLL2020-WO 13 Installing the scanner 14 Appendices A. Connector types and pin definiti ...
-
Datalogic Scanning DLL2020-WO - page 4
Preface The Datalogic DLL2020-WO is a high performance omni-directional scanner , which provides optimal scanning conditions. The DLL2020-WO shar es the same quality of the GOLDRUSH TM polygon and Scantium decoder chip as Datalogic’ s popular Hunter H-3010, Pollux P-4010 and Castor C-5010 scanners. T ogether with its compact and er gonomic design ...
-
Datalogic Scanning DLL2020-WO - page 5
Chapter 1 The DLL2020-WO ...
-
Datalogic Scanning DLL2020-WO - page 6
1.1 Unpacking the DLL2020-WO T ake the scanner and its accessories out of the box and remove all packing materials. Refer to the packing list in order to ensur e that you have received all the items or dered. Visually inspect the scanner and accessories for any visible traces of damage. Refer to the figure in paragraph 1.3 to locate the interface l ...
-
Datalogic Scanning DLL2020-WO - page 7
The various parts of the DLL2020-WO are: Sleep mode switch If a sleep mode time-out has been programmed, the scanner can be reactivated by pr essing this switch. The sleep-mode feature can be pr ogram- med by means of the menu labels in the Configuration Guide. NOTE: The default value for the sleep mode time-out is set to 30 minutes. When the scann ...
-
Datalogic Scanning DLL2020-WO - page 8
1.2 Scanning bar codes with the DLL2020-WO The DLL2020-WO is an omnidirectional scanner featuring a 4-dir ectional scan field with a 16-lines scan pattern. Bar codes can easily be read by presenting them to the scanner . The scan volume is illustrated in the figure above. The optimal r eading zone lies between 3 and 15 cm from the scanner window. H ...
-
Datalogic Scanning DLL2020-WO - page 9
The Dll2020-wo scanner can be used handsfree as well as hand held , e.g.: a) Handsfree scanning by presenting the item to the scanner . b) Bar code labels can also be scanned in hand held mode, by taking the scanner by the handle and hold it in front of the bar code label on the product. 1 2 2 1 The DLL2020-WO 5 ...
-
Datalogic Scanning DLL2020-WO - page 10
c) Y ou can also hold the scanner without the handle. 1 2 6 The DLL2020-WO ...
-
Datalogic Scanning DLL2020-WO - page 11
1.3 Scanner labelling There ar e four labels on the scanner . The first three labels can be found on the housing of the DLL2020-WO, as indicated in the figures below . The fourth label is visible through the scanner window . All the labels have been attached by the manufacturer and should in no case be removed. The scanner’ s serial number can be ...
-
Datalogic Scanning DLL2020-WO - page 12
Laser safety English: The DLL2020-WO scanner complies with safety standard IEC 825-1 (1993) for a Class 1 laser product. It also complies with U.S. 21CFR1040 as applicable to a Class IIa laser product. Avoid long term viewing of direct laser light. German: Der Strichcode-Scanner DLL2020-WO entspricht den Sicherheitsvorschriften nach IEC 825-1 (1993 ...
-
Datalogic Scanning DLL2020-WO - page 13
Finnish: DLL2020-WO-skanneri täyttää luokan 1 lasertuotteelle IEC 825-1:ssä (1993) asetetut turvavaatimukset. Se täyttää myös U.S. 21CFR1040:ssa asetetut vaatimukset siltä osin kuin ne koskevat luokan IIa lasertuotetta. Vältä pitkäaikaista suoraan laservaloon katsomista. Swedish: Avsökaren DLL2020-WO uppfyller säkerhetsnormen IEC 825- ...
-
Datalogic Scanning DLL2020-WO - page 14
Optical The use of optical instruments with this product will increase eye hazar d. Optical instruments include binoculars, microscopes and magnifying glasses but do not include eye glasses worn by the user . Radiant Energy The DLL2020-WO uses a low-power laser diode operating at 650 nm in an opto-mechanical scanner resulting in less than 0.7 mW pe ...
-
Datalogic Scanning DLL2020-WO - page 15
1.4 Maintaining the scanner The DLL2020-WO scanner requir es little maintenance. Only occasional cleaning of the scanner window is necessary in order to r emove dir t and fingerprints. The scanner can be cleaned during operation. T o this end use a non-abrasive glass spray cleaner and a soft lint-free cloth only . 1.5 Contr olling the scanner from ...
-
Datalogic Scanning DLL2020-WO - page 16
POS system Polaris P-7010 Scanner control 12 The DLL2020-WO DLL2020-WO ...
-
Datalogic Scanning DLL2020-WO - page 17
Chapter 2 Installing the DLL2020-WO ...
-
Datalogic Scanning DLL2020-WO - page 18
14 Installing the DLL2020-WO 2.1 Installing the scanner This chapter describes the instructions necessary for installing the DLL2020-WO scanner . Due to many POS systems on the market, a lar ge number of communication cables is available. Make sure that you have the right cable to connect the scanner to your POS or computer . Follow these steps car ...
-
Datalogic Scanning DLL2020-WO - page 19
Installing the DLL2020-WO 15 2. Y ou have four options to connect the scanner to your POS or computer . A) RS232 direct power For those systems which supply electrical power on the serial port (minimal requir ements: +5 V dc, 250 mA), the following set-up is applicable. Plug the cable with the 10-pin modular jack into the scanner port until a firm ...
-
Datalogic Scanning DLL2020-WO - page 20
16 Installing the DLL2020-WO B) Keyboar d W edge direct power For those systems which supply electrical power on the keyboard port (minimal requirements: +5 V dc, 250 mA), the following set-up is applicable. Plug the cable with the 10-pin modular jack into the scanner port until a firm ‘click’ is heard. Connect the female connector at the other ...
-
Datalogic Scanning DLL2020-WO - page 21
Installing the DLL2020-WO 17 C) RS232 non direct power For those systems which do not supply electrical power on the serial port, the following set-up is applicable. Plug the cable with the 10-pin modular jack into the scanner port until a firm ‘click’ is heard. Plug the other connector into the splitter box, as illustrated in the figure below ...
-
Datalogic Scanning DLL2020-WO - page 22
18 Installing the DLL2020-WO D) Keyboard W edge non direct power For those systems which do not supply electrical power on the keyboard port, the following set-up is applicable. Plug the cable with the 10-pin modular jack into the scanner port until a firm ‘click’ is heard. Plug the other connector into the splitter box as illustrated in the fi ...
-
Datalogic Scanning DLL2020-WO - page 23
Installing the DLL2020-WO 19 OPEN PROGRAMMING MODE 1. T o select the scanner interface (RS232 factory default), scan the following codes: 1. Open the scanner Programming Mode by scanning code 1 2. - Return to RS232 default by scanning code 2 OR - Return to Keyboard W edge default by scanning code 3 IMPORT ANT 8 71 23 45 1 0 00 01 ...
-
Datalogic Scanning DLL2020-WO - page 24
20 Installing the DLL2020-WO RETURN TO RS232 DEF AUL T 2. IMPORT ANT: Programming Mode is closed after scanning this code. RETURN TO KEYBOARD WEDGE DEF AUL T 3. IMPORT ANT: Programming Mode is closed after scanning this code. 71 23 45 1 0 01 00 71 23 45 1 0 01 31 ...
-
Datalogic Scanning DLL2020-WO - page 25
Appendices A. Connector types and pin definitions B. T echnical Specifications C. T r oubleshooting ...
-
Datalogic Scanning DLL2020-WO - page 26
22 Appendices A. Connector types and pin definitions The Dll2020-wo has a dual interface: RS232/Keyboard Wedge. The pin definition for the scanner port and the connector to be used for the por t are shown in the connection diagram below . Connection Diagram PC - CLOCK DESCRIPTION RJ - 48 PCB ( front view ) Scanner port 10 pin connector CTS RXD Pin ...
-
Datalogic Scanning DLL2020-WO - page 27
Appendices 23 B. T echnical specifications Electrical Power supply voltage 100 - 250 V ac, 50/60 Hz DC input to scanner + 5 V dc ± 5%, 250 mA Dual interface RS232/Keyboard Wedge Optical Light source Visible laser diode (650nm) Depth of field 250 mm Scan pattern 4 directions scan field, 16 lines scan pattern Scan rate 800 scans / second Decoding Ba ...
-
Datalogic Scanning DLL2020-WO - page 28
24 Appendices C. T roubleshooting This section contains information on solving problems you may encounter when using the scanner . If troubles occur , take a moment to read the information in this section. However , before referring to the diagnostic tips make sure that the scanner is installed as described in Chapter 2 and that all cables are pr o ...
-
Datalogic Scanning DLL2020-WO - page 29
Appendices 25 The scanner is on but a bar code cannot be read. The LED is red. Diagnostic Tips n The scanner window is dirty. Clean the n scanner window as described in the n Maintenance section. n The presented bar code type is not n enabled. Select the bar code type with n the Configuration Guide. n The scanner is disabled by the host. n Refer to ...
-
Datalogic Scanning DLL2020-WO - page 30
26 Appendices The green LED stays on. A bar code is read by the scanner but not accepted by the host system. Diagnostic Tips The scanner is continuously seeing a bar code. Remove all bar code labels from the scan volume of the scanner and try again. The scanner cannot send the data to the host system. There is no proper handshaking between the scan ...
У вас вопрос, касающийся Datalogic Scanning DLL2020-WO?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Datalogic Scanning DLL2020-WO, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Datalogic Scanning DLL2020-WO со всей вероятностью он захочет поделиться методом ее решения.