-
Tektronix VX4801 - page 1
User Manual VX4801 Pr ogrammable Digital I/O Module 070-9153-03 This document applies for firmware version 1.00 and above. ...
-
Tektronix VX4801 - page 2
Copyright T ektronix, Inc. All rights reserved. T ektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes that in all previously published material. Specifications and price change privileges reserved. Printed in the U.S.A. T ektronix, Inc., P .O. Box 1000, W ilsonville, OR 97070 ...
-
Tektronix VX4801 - page 3
W ARRANTY T ektronix warrants that this product will be free from defects in materials and workmanship for a period of three (3) years from the date of shipment. If any such product proves defective during this warranty period, T ektronix, at its option, either will repair the defective product without charge for parts and labor , or will provide a ...
-
Tektronix VX4801 - page 4
EC Declaration of Conformity We T ektronix Holland N.V . Marktweg 73A 8444 AB Heerenveen The Netherlands declare under sole responsibility that the VX4801 meets the intent of Directive 89/336/EEC for Electromagnetic Compatibility . Compliance was demonstrated to the following specifications as listed in the Official Journal of the European Communit ...
-
Tektronix VX4801 - page 5
...
-
Tektronix VX4801 - page 6
...
-
Tektronix VX4801 - page 7
$$# $ " "$ !$ # 0641'7&6,10 ...
-
Tektronix VX4801 - page 8
VX4801 Programmable Digital I/O Module iii General Safety Summary Review the following safety precautions to avoid injury and prevent damage to this product or any products connected to it. Only qualified personnel should perform service pr ocedur es. While using this product, you may need to access other parts of the system. Read the General Safet ...
-
Tektronix VX4801 - page 9
General Safety Summary iv VX4801 Programmable Digital I/O Module Safety T erms and Symbols These terms may appear in this manual: W ARNING. W arning statements identify conditions or practices that could r esult in injury or loss of life. CAUTION. Caution statements identify conditions or practices that could r esult in damage to this pr oduct or o ...
-
Tektronix VX4801 - page 10
...
-
Tektronix VX4801 - page 11
...
-
Tektronix VX4801 - page 12
...
-
Tektronix VX4801 - page 13
...
-
Tektronix VX4801 - page 14
...
-
Tektronix VX4801 - page 15
...
-
Tektronix VX4801 - page 16
...
-
Tektronix VX4801 - page 17
...
-
Tektronix VX4801 - page 18
...
-
Tektronix VX4801 - page 19
...
-
Tektronix VX4801 - page 20
Output high voltage (V oh ) min typ max units I o = –20 A l o = –6 mA Output low voltage (V ol ) l o = 20 A l o = 24 mA Output low current (l ol ) Input high voltage (V ih ) Input low voltage (V il ) * Input current (l in ) T ri-state leakage current (l oz ) 4.4 3.84 5.0 4.2 V V 0 0 0.1 0.5 V V 24 mA 2.0 V 0.8 V 230 A A 5.0 0.5 ...
-
Tektronix VX4801 - page 21
...
-
Tektronix VX4801 - page 22
...
-
Tektronix VX4801 - page 23
...
-
Tektronix VX4801 - page 24
...
-
Tektronix VX4801 - page 25
...
-
Tektronix VX4801 - page 26
...
-
Tektronix VX4801 - page 27
...
-
Tektronix VX4801 - page 28
...
-
Tektronix VX4801 - page 29
...
-
Tektronix VX4801 - page 30
...
-
Tektronix VX4801 - page 31
...
-
Tektronix VX4801 - page 32
...
-
Tektronix VX4801 - page 33
...
-
Tektronix VX4801 - page 34
...
-
Tektronix VX4801 - page 35
...
-
Tektronix VX4801 - page 36
...
-
Tektronix VX4801 - page 37
...
-
Tektronix VX4801 - page 38
...
-
Tektronix VX4801 - page 39
...
-
Tektronix VX4801 - page 40
...
-
Tektronix VX4801 - page 41
...
-
Tektronix VX4801 - page 42
...
-
Tektronix VX4801 - page 43
...
-
Tektronix VX4801 - page 44
...
-
Tektronix VX4801 - page 45
...
-
Tektronix VX4801 - page 46
...
-
Tektronix VX4801 - page 47
...
-
Tektronix VX4801 - page 48
...
-
Tektronix VX4801 - page 49
...
-
Tektronix VX4801 - page 50
...
-
Tektronix VX4801 - page 51
...
-
Tektronix VX4801 - page 52
...
-
Tektronix VX4801 - page 53
...
-
Tektronix VX4801 - page 54
...
-
Tektronix VX4801 - page 55
...
-
Tektronix VX4801 - page 56
...
-
Tektronix VX4801 - page 57
...
-
Tektronix VX4801 - page 58
...
-
Tektronix VX4801 - page 59
...
-
Tektronix VX4801 - page 60
...
-
Tektronix VX4801 - page 61
...
-
Tektronix VX4801 - page 62
...
-
Tektronix VX4801 - page 63
...
-
Tektronix VX4801 - page 64
...
-
Tektronix VX4801 - page 65
...
-
Tektronix VX4801 - page 66
...
-
Tektronix VX4801 - page 67
...
-
Tektronix VX4801 - page 68
...
-
Tektronix VX4801 - page 69
...
-
Tektronix VX4801 - page 70
...
-
Tektronix VX4801 - page 71
...
-
Tektronix VX4801 - page 72
...
-
Tektronix VX4801 - page 73
...
-
Tektronix VX4801 - page 74
...
-
Tektronix VX4801 - page 75
...
-
Tektronix VX4801 - page 76
...
-
Tektronix VX4801 - page 77
VX4801 Programmable Digital I/O Module A–19 Appendix E: Performance V erification 123 This procedure verifies the performance of the VX4801 Programmable Digital I/O Module. The test sequences may be performed in your current VXIbus system if it meets the requirements described in T able 2. Also, it is not necessary to complete the entire procedur ...
-
Tektronix VX4801 - page 78
Appendix E: Performance V erification A–20 VX4801 Programmable Digital I/O Module NOTE . Commands to the VX4801 may be enter ed in upper or lower case. However , to avoid confusion between the alphanumeric characters; e.g. one (1) and L or zer o( 0) and o, all commands ar e shown in the case which pr ovides the gr eatest distinction. Use special ...
-
Tektronix VX4801 - page 79
Appendix E: Performance V erification VX4801 Programmable Digital I/O Module A–21 34 18 1 Byte 3 LSB Byte 2 MSB Byte 5 LSB GND Byte 0 LSB DAK 6 DA V 5 GND GND GND 1 34 39 50 33 17 1 14 25 13 8 Byte 4 LSB DRd Byte 2 T ri-St Byte 1 T ri-St VX4801 Slave Module VX4801 Under-test Byte 0 T ri-St Byte 5 T ri-St Byte 4 T ri–St Byte 3 T ri-St RFD 17 33 ...
-
Tektronix VX4801 - page 80
Appendix E: Performance V erification A–22 VX4801 Programmable Digital I/O Module VX4801 Under-T est Configuration In order to perform this procedure, the VX4801 under-test must be installed in an approved VXIbus system. At a minimum, the system must contain the elements listed in T able 2. T able 2: Elements of a Minimum VX4801 Under-T est Syste ...
-
Tektronix VX4801 - page 81
Appendix E: Performance V erification VX4801 Programmable Digital I/O Module A–23 T est Record Photocopy the T est Record, and use it to record the performance verification results for your module. T able 4: VX4801 T est Record VX4801 Serial Number: T emperature and Relative Humidity: Date of Last Calibration: V erification Performed by: Certific ...
-
Tektronix VX4801 - page 82
Appendix E: Performance V erification A–24 VX4801 Programmable Digital I/O Module Self T est The VX4801 includes a built-in self test function (BITE) which is automatically executed each time the power is turned on and when the Internal Self T est (S) command is issued. BITE uses internal routines and circuitry to confirm basic I/O functionality ...
-
Tektronix VX4801 - page 83
Appendix E: Performance V erification VX4801 Programmable Digital I/O Module A–25 NOTE . If you ar e using National Instruments NI-488.2 softwar e you may wish to select the buffer 1 mode to allow mor e comfortable viewing of the ASCII r esponse. Just type buffer 1. 1. T o verify the system configuration, send the T ABLE command to the Slot 0 Res ...
-
Tektronix VX4801 - page 84
Appendix E: Performance V erification A–26 VX4801 Programmable Digital I/O Module (Observe: VX4521 Slot 0 indicates S in 2nd digit) NOTE . The zer o length r ead serves to un-addr ess the Slot 0 controller which allows it to detect the VXIbus interrupt and assert the SRQ. b. Check that the F AILED light on the VX4801-device-under ...
-
Tektronix VX4801 - page 85
Appendix E: Performance V erification VX4801 Programmable Digital I/O Module A–27 2. Perform a self test and query for any error codes (in ASCII format) with the VX4801 device-under-test and the Slave VX4801: (Observe: NO ERRORS) ? ...
-
Tektronix VX4801 - page 86
Appendix E: Performance V erification A–28 VX4801 Programmable Digital I/O Module 4. T o verify the even byte data inputs and the odd byte data outputs, reset the VX4801 to its power-up state and then set its mode for the even bytes (0, 2, 4) to be active low inputs, for the odd bytes (1, 3, 5) to be active high outputs loaded with a Load Output ...
-
Tektronix VX4801 - page 87
Appendix E: Performance V erification VX4801 Programmable Digital I/O Module A–29 (Observe: response of 00FF00FF00FF) b. Repeat the above test, this time with the even bytes set as inputs and ...
-
Tektronix VX4801 - page 88
Appendix E: Performance V erification A–30 VX4801 Programmable Digital I/O Module (Observe: response of 00FF00FF00FF) d. Set the Slave to un-assert external tri-state signals. Then set the VX4801 for the odd bytes to be inputs, for the even bytes to be outputs with a Load Output value of 00, and ...
-
Tektronix VX4801 - page 89
Appendix E: Performance V erification VX4801 Programmable Digital I/O Module A–31 This test sequence verifies that data can be transferred to and from the VX4801 using the four handshake signal lines Data Ready (DRD), Data Acknowledge (DAK), Ready for Data (RFD), and Data A vailable (DA V). NOTE . T yping err ors will result in a VX4801 err or co ...
-
Tektronix VX4801 - page 90
Appendix E: Performance V erification A–32 VX4801 Programmable Digital I/O Module d. Set the Slave to initialize byte 2 with an Output Data value of 01 (asserts RFD to the VX4801) and verify that the VX4801 correspondingly asserts DA V : (Observe: VX4801 DA V light on) e. Set the Slave to input bytes 1 and 3 an ...
-
Tektronix VX4801 - page 91
Appendix E: Performance V erification VX4801 Programmable Digital I/O Module A–33 e. Send a byte 5 input command to the VX4801 and verify that the DAK light is on. Then read the data, observe a response of AA, perform a second read and observe that the VX4801 is again waiting for a DRD strobe: (Observe VX4801 DAK ligh ...
У вас вопрос, касающийся Tektronix VX4801?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Tektronix VX4801, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Tektronix VX4801 со всей вероятностью он захочет поделиться методом ее решения.