-
Dell Z01G - page 1
Alienware Graphics Amplifier User’s Guide Regulatory Model: Z01G Regulatory Type: Z01G001 ...
-
Dell Z01G - page 2
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 201 ...
-
Dell Z01G - page 3
Contents Before Working Inside Your Alienware Graphics Amplifier........................................................................................ 5 Before You Begin .............................................................................................. 5 Safety Instructions ............................................................. ...
-
Dell Z01G - page 4
Troubleshooting........................................................................ 35 Getting Help and Contacting Alienware............................... 36 Self-Help Resources ........................................................................................ 36 Contacting Alienware ...................................................... ...
-
Dell Z01G - page 5
Before Working Inside Your Alienware Graphics Amplifier CAUTION: To avoid damaging the components and cards, handle them by their edges and avoid touching pins and contacts. NOTE: The images in this document may differ from your device depending on the configuration you ordered. Before You Begin 1 Disconnect your device and all attached devices fro ...
-
Dell Z01G - page 6
CAUTION: Only a certified service technician is authorized to remove the device cover and access any of the components inside the device. See the safety instructions for complete information about safety precautions, working inside your device, and protecting against electrostatic discharge. CAUTION: Before touching anything inside your device, gro ...
-
Dell Z01G - page 7
After Working Inside Your Alienware Graphics Amplifier CAUTION: Leaving stray or loose screws inside your device may severely damage your device. 1 Replace all screws and make sure that no stray screws remain inside your device. 2 Connect any external devices, peripherals, and cables you removed before working on your device. 3 Replace any media ca ...
-
Dell Z01G - page 8
Views This chapter lists out the features available on your Alienware Graphics Amplifier. Front View 1 AlienHead/Docking status light 2 Service Tag/Regulatory labels 8 ...
-
Dell Z01G - page 9
Back View 1 Release latch 2 Power port 3 Power-supply diagnostic button 4 Power-supply status light 5 USB 3.0 ports (4) 6 External graphics port 7 Graphics-card slot 9 ...
-
Dell Z01G - page 10
Graphics Cable 1 Release clips (2) 2 Undock button 3 Docking status light 4 Graphics cable 10 ...
-
Dell Z01G - page 11
Specifications Dimensions and Weight Width 138 mm (5.43 in) Height 150 mm (5.90 in) Depth 375 mm (14.76 in) Ports and Connectors External: USB USB 3.0 ports (4) Video One external graphics port Internal: Graphics Card Graphics-card slot Device Environment Feature Specification Temperature range: Operating 0°C to 40°C (32°F to 104°F) Storage – ...
-
Dell Z01G - page 12
Device Environment Feature Specification Altitude: Operating –15.20 m to 3048 m (–50 ft to 10,000 ft) Storage –15.20 m to 10,668 m (–50 ft to 35,000 ft) Airborne contaminant level G1 as defined by ISA-S71.04-1985 12 ...
-
Dell Z01G - page 13
Using the Alienware Graphics Amplifier This section will provide procedures on how to install and uninstall the Graphics card. WARNING: Disconnect all cables before working inside your device. CAUTION: Handle the components with care. Hold the graphics card at its edges. 13 ...
-
Dell Z01G - page 14
Installing the Graphics Card NOTE: The graphics card is sold separately. 1 Slide the release latch to release the cover. 1 release latch 2 cover 14 ...
-
Dell Z01G - page 15
2 Lift the cover and open it as far as possible. 1 cover 3 Remove the screws that secure the graphics card fillers to the chassis. NOTE: Remove only one filler if you are installing a single width graphics card. 15 ...
-
Dell Z01G - page 16
4 Lift the graphics card fillers away from the chassis. 1 screws (2) 2 graphics card fillers (2) 16 ...
-
Dell Z01G - page 17
5 Disconnect the power cables from the slots on the device. 1 power cables (2) 2 slots (2) 6 Align the connector on the graphics card with the slot on the system board and press down the card until it locks into position. 17 ...
-
Dell Z01G - page 18
7 Replace the screws that secure the graphics card to the chassis. 1 screws (2) 2 graphics card 18 ...
-
Dell Z01G - page 19
8 Connect the power cables to the power-cable connectors on the graphics card. NOTE: The location of the power-cable connectors may be different on your graphics card. 1 power cables (2) 2 power-cable connectors (2) 19 ...
-
Dell Z01G - page 20
9 Close the cover and press down until it locks into position. 1 cover 20 ...
-
Dell Z01G - page 21
Removing the Graphics Card 1 Slide the release latch to release the cover. 1 release latch 2 cover 21 ...
-
Dell Z01G - page 22
2 Lift the cover and open it as far as possible. 1 cover 22 ...
-
Dell Z01G - page 23
3 Press the tabs and disconnect the power cables from the graphics card. 1 power cables (2) 2 tabs (2) 4 Remove the screws that secure the graphics card to the chassis. 5 Press the release latch to release the graphics card from the slot on the system board. 23 ...
-
Dell Z01G - page 24
6 Lift the graphics card away from the chassis. 1 release latch 2 screws (2) 3 graphics card 7 Slide the graphics card fillers into the slots on the graphics card. 8 Replace the screws that secure the graphics card fillers to the chassis. 24 ...
-
Dell Z01G - page 25
9 Connect the power cables to the slots on the device. 1 screws (2) 2 graphics card fillers 25 ...
-
Dell Z01G - page 26
10 Close the cover and press down until it locks into position. 1 cover 26 ...
-
Dell Z01G - page 27
Setting Up Your Alienware Graphics Amplifier 1 Install the graphics card. See “ Installing the Graphics Card ”. 2 Connect the power cable to the power port on the Alienware graphics amplifier. 1 power port 2 power cable 27 ...
-
Dell Z01G - page 28
3 NOTE: It is recommended to shut down the computer and connect the Graphics cable from the Alienware Graphics Amplifier to your computer and then powering on the computer to dock with the graphics amplifier. Press the release clips and connect one end of the graphics cable to the external graphics port on the Alienware graphics amplifier. 1 extern ...
-
Dell Z01G - page 29
4 NOTE: Shut down your computer before you connect the graphics cable. Press the release clips and connect the other end of the graphics cable to the external graphics port on your computer. The light on the graphics cable turns on indicating the Alienware Graphics Amplifier is connected and ready to use. NOTE: If required, connect the display to t ...
-
Dell Z01G - page 30
2 Connect the graphics cable from the Alienware Graphics Amplifier to the external graphics port on your computer. NOTE: For the location of the external graphics port, see the documentation that shipped with your computer. The AlienHead logo on the Alienware Graphics Amplifier lights up and a dialog box appears on the computer asking you to restar ...
-
Dell Z01G - page 31
Disconnecting Alienware Graphics Amplifier CAUTION: Do not disconnect the graphics cable until the computer has shut down and the light on the graphics cable has turned off. 1 Save and close all open files and exit all open applications. 2 Shut down your computer. CAUTION: Do not disconnect the graphics cable until the computer has shut down and th ...
-
Dell Z01G - page 32
Alternate Methods to Disconnect Alienware Graphics Amplifier CAUTION: Do not disconnect the graphics cable until the computer has shut down and the light on the graphics cable has turned off. Using Keyboard Shortcut 1 Save and close all open files and exit all open applications. 2 Press the Fn+F1 keys on the keyboard of your computer. 3 A dialog bo ...
-
Dell Z01G - page 33
Undock Button Settings This section will provide procedure on how to set the computer’s behavior when the undock button on the graphics cable is pressed. 1 Launch AlienAdrenaline . Windows 8.1 : a) On the Start screen, browse to Apps and click the Alienware Command Center tile. b) In the Alienware Command Center window, click AlienAdrenaline . Wi ...
-
Dell Z01G - page 34
Installing the Alienware Graphics Amplifier Software NOTE: Alienware Graphics Amplifier software is already installed on your computer. It is a standalone application and not a part of Alienware Command Center. NOTE: If the Alienware Graphics Amplifier software or Alienware Command Center is not available on your computer, you can download and inst ...
-
Dell Z01G - page 35
Troubleshooting Issue Solution Graphics card is not detected Download and install the latest driver for the video card installed in the Alienware Graphics Amplifier. For more information, see the document that came with the video card you purchased. NOTE: The graphics card is sold separately. The video ports and the display on your computer will be ...
-
Dell Z01G - page 36
Getting Help and Contacting Alienware Self-Help Resources You can get information and help on Alienware products and services using these online self-help resources: Self-Help Information Self-Help Options Accessing Windows Help Windows 8.1 — Open the Search charm, type Help and Support in the search box and press Enter . Windows 7 — Click Star ...
У вас вопрос, касающийся Dell Z01G?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Dell Z01G, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Dell Z01G со всей вероятностью он захочет поделиться методом ее решения.