-
Chamberlain PD210 -1/2 HP - page 1
GARAGE DOOR OPENER Models PD210 -1/2 HP PD212 -1/2 HP For Residential Use Only Owner’s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT CLOSE unless the Protector System ® is connected and properly aligned. ■ Periodic checks of t ...
-
Chamberlain PD210 -1/2 HP - page 2
2 Introduction Pages 2-7 Safety symbol and signal word review ........................2 Preparing your garage door ........................................3 T ools needed ...............................................................3 Planning ..................................................................4-5 Carton inventory .................. ...
-
Chamberlain PD210 -1/2 HP - page 3
3 Pliers W ire C u tters Cla w Hammer Hack Sa w Scre w dri v er Adj u sta b le End W rench Sockets and W rench 1/2", 5/ 8 ", 7/16", 9/16" and 1/4" Drill T ape Meas u re 2 1 Stepladder Pencil Drill Bits 3/16", 5/16" and 5/32" Carpenter's Le v el (optional) T o prevent damage to garage door and opener: • ...
-
Chamberlain PD210 -1/2 HP - page 4
Safety Reversing Sensor Support bracket & fastening hardware is required. See page 17. — — — — — — — — Header Wall FINISHED CEILING Torsion Spring Extension Spring OR Safety Reversing Sensor Gap between floor and bottom of door must not exceed 1/4" Access Door Wall- mounted Door Control Horizontal and vertical reinforcement ...
-
Chamberlain PD210 -1/2 HP - page 5
CLOSED POSITION Access Door Gap between floor and bottom of door must not exceed 1/4" Safety Reversing Sensor Safety Reversing Sensor Wall- Mounted Door Control Cable Pulley Bracket Door Bracket Straight Door Arm Trolley Header Wall T-rail Garage Door Cable Emergency Release Rope & Handle Chain Header Bracket Curved Door Arm 5 Planning (Co ...
-
Chamberlain PD210 -1/2 HP - page 6
6 Cable Pulley Bracket Trolley Header Bracket Chain and Cable in Dispensing Carton Curved Door Arm Section Straight Door Arm Section Safety Labels and Literature Sprocket Cover Rail Brace (3) T-rail Center Section (each) (2) T-rail End Section (2) Hanging Brackets U P C E I L I N G M O U N T O N L Y Door Bracket SECURITY ✚ ® Single-Button Remote ...
-
Chamberlain PD210 -1/2 HP - page 7
Hardwar e Inventor y Separate all hardware and group as shown below for the assembly and installation procedures. 7 Lock W asher 5/16" (4) Lock Nu t 1/4"-20x7/16" (12) Nu t 5/16"-1 8 (5) W ashered Bolt 5/16"-1 8 x1/2" (2) (mo u nted in opener) Carriage Bolts 1/4"-20x1/2" (12) Hex Bolt 5/16"-1 8 x7/ 8 &qu ...
-
Chamberlain PD210 -1/2 HP - page 8
8 ASSEMBL Y STEP 1 Assemble the T -Rail and Attach the Cable Pulley Bracket T o avoid installation difficulties, do not run the garage door opener until instructed to do so. 1. Align the four T -rail sections on a flat surface exactly as shown . Center sections are interchangeable. Front and back sections are also interchangeable for ease of assemb ...
-
Chamberlain PD210 -1/2 HP - page 9
9 ASSEMBL Y STEP 2 Install the T rolley • Attach the trolley threaded shaft to the trolley with the lock washer and nuts as shown. • As a temporary stop, insert a screwdriver into the hole in the front end of the T -rail. • Slide the trolley assembly along the rail to the screwdriver stop. NOTE: If trolley hits against any nuts on the T -rail ...
-
Chamberlain PD210 -1/2 HP - page 10
10 ASSEMBL Y STEP 4 Install the Chain/Cable and Attach the Sprocket Cover INST ALLING THE CHAIN/CABLE 1. Pull the cable loop from the carton and fasten it to the trolley with a master link from the hardware bag. (See Figure 1) • Push pins of master link bar through cable loop and hole in front end of trolley . • Push master link cap over pins a ...
-
Chamberlain PD210 -1/2 HP - page 11
ASSEMBL Y STEP 5 Tighten the Chain and Cable • Spin the inner nut and lock washer down the trolley threaded shaft, away from the trolley . • T o tighten the chain, turn outer nut in the direction shown. AS YOU TURN THE NUT , KEEP THE CHAIN FROM TWISTING. • When the chain is approximately 1/2" (1.3 cm) above the base of the T -rail at its ...
-
Chamberlain PD210 -1/2 HP - page 12
12 INST ALLA TION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door . SECTIONAL DOOR AND ONE-PIECE DOOR WITH TRACK 1. Close the door and mark the inside vertical centerline of the garage door . 2. Extend the line onto the header wall above the d ...
-
Chamberlain PD210 -1/2 HP - page 13
13 Header Wall Vertical Centerline Vertical Centerline of Garage Door 2x4 Unfinished Ceiling 2x4 OPTIONAL CEILING MOUNT FOR HEADER BRACKET Structural Supports ONE-PIECE DOOR WITHOUT TRACK 1. Close the door and mark the inside vertical centerline of your garage door . Extend the line onto the header wall above door , as shown. If headroom clearance ...
-
Chamberlain PD210 -1/2 HP - page 14
14 INST ALLA TION STEP 2 Install the Header Bracket Y ou can attach the header bracket either to the wall above the garage door , or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry , use concrete anchors (not provided). W ALL HE ...
-
Chamberlain PD210 -1/2 HP - page 15
Clevis Pin 5/16" x 2-3/4" Ring Fastener 15 INST ALLA TION STEP 3 Attach the T -Rail to the Header Bracket • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you’ll need help. Have someone hold the opener securely on a temporary support t ...
-
Chamberlain PD210 -1/2 HP - page 16
16 ONE-PIECE DOOR WITHOUT TRACK • With the door fully open and parallel to the floor , measure the distance from the floor to the top of the door . • Using a stepladder as a support, raise the top of the opener to this height. • The top of the door should be level with the top of the motor unit. Do not position the opener more than 2" (5 ...
-
Chamberlain PD210 -1/2 HP - page 17
17 INST ALLA TION STEP 5 Hang the Opener T wo representative installations are shown. Y ours may be different. Hanging brackets should be angled (Figure 1) to provide rigid support. On finished ceilings (Figure 2), attach a sturdy metal bracket to structural supports before installing the opener . This bracket and fastening hardware are not provide ...
-
Chamberlain PD210 -1/2 HP - page 18
18 To release wire, push in ta b with screwdriver tip Door Control Connections Red Grey White Strip wire 7/16" (11 mm) 7/16" (11 mm) L O C K L IG H T Slot Figure 4 REMOVE COVER INST ALLA TION STEP 6 Install the Door Control Locate door control within sight of the door at a minimum height of 5 feet (1.5 m) where small children cannot reach ...
-
Chamberlain PD210 -1/2 HP - page 19
19 INST ALLA TION STEP 7 Install the Lights • Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. • Install up to a 100 watt maximum light bulb in the socket. The lights will turn ON and remain lit for approximately 4-1/2 minutes when powe ...
-
Chamberlain PD210 -1/2 HP - page 20
20 INST ALLA TION STEP 9 Electrical Requirements T o avoid installation difficulties, do not run the opener at this time. T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn't fit into the outlet you have, co ...
-
Chamberlain PD210 -1/2 HP - page 21
21 Facing the door from inside the garage INST ALLA TION STEP 10 Install The Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. IMPORT ANT INFORMA TION ABOUT THE SAFETY REVERSING SENSOR When properly connected and aligned, the sensor will detect an o ...
-
Chamberlain PD210 -1/2 HP - page 22
22 FLOOR MOUNT (RIGHT SIDE) WALL MOUNT (RIGHT SIDE) DOOR TRACK MOUNT (RIGHT SIDE) Indicator light Lens Lip Sensor Bracket Door T rack Sensor Bracket Extension Bracket (See Accessories) Lens Indicator light Attach with concrete anchors (not provided) Inside G arage W all Indicator light Sensor Bracket Lens Extension Bracket (See Accessories) Inside ...
-
Chamberlain PD210 -1/2 HP - page 23
23 1/4"-20x1/2" Carriage bolt Lens Wing nut Figure 4 MOUNTING AND WIRING THE SAFETY SENSORS • Slide a 1/4"-20x1/2" carriage bolt head into the slot on each sensor . Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door . Be sure the lens is not obstructed by a bracket extension (Fi ...
-
Chamberlain PD210 -1/2 HP - page 24
24 Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact your door manufacturer for reinforcement kit. INST ALLA TION STEP 11 Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following page. A horizontal reinforcement bra ...
-
Chamberlain PD210 -1/2 HP - page 25
25 ONE-PIECE DOORS Please read and comply with the warnings and reinforcement instructions on the previous page. They apply to one-piece doors also. • Center the door bracket on the top of the door , in line with the header bracket as shown. Mark either the left and right, or the top and bottom holes. • Metal Doors: Drill 3/16" pilot holes ...
-
Chamberlain PD210 -1/2 HP - page 26
26 INST ALLA TION STEP 12 Connect Door Arm to T rolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONL Y • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley . Slide the outer trolley back (away from t ...
-
Chamberlain PD210 -1/2 HP - page 27
ALL ONE-PIECE DOORS 1. Assemble the door arm: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • With the door closed, connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis pin. • Secure with a ring fastener . 2. Adjustment proce ...
-
Chamberlain PD210 -1/2 HP - page 28
28 ADJUSTMENT STEP 1 Adjust the UP and DOWN T ravel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or down. T o operate the opener , press the Door Control push bar . Run the opener through a complete travel cycle. • Does the door open and close completely? • Does the door stay closed and not rev ...
-
Chamberlain PD210 -1/2 HP - page 29
ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door . If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction. Weather ...
-
Chamberlain PD210 -1/2 HP - page 30
Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSL Y INJURED or KILLED by a closing garage door . • Safety reversal system MUST be tested every month. • If one control (for ce or travel limits) is adjusted, the other control may also need adjustment. • After ANY adjustments are made, t ...
-
Chamberlain PD210 -1/2 HP - page 31
OPERA TION 31 Using Y our Garage Door Opener Y our Security ✚ ® opener and hand-held remote control have been factory-set to a matching code which changes with each use, randomly accessing over 100 billion new codes. Y our opener will operate with up to eight Security ✚ ® remote controls and one Security ✚ ® Keyless Entry System. If you pu ...
-
Chamberlain PD210 -1/2 HP - page 32
T o Open the Door Manually The door should be fully closed if possible. Pull down on the emergency release handle and lift the door manually . T o reconnect the door to the opener , press the door control push bar . The lockout feature prevents the trolley from reconnecting automatically , Pull the emergency release handle down and back (toward the ...
-
Chamberlain PD210 -1/2 HP - page 33
33 Care of Y our Opener LIMIT AND FORCE ADJUSTMENTS: Weather conditions may cause some minor changes in door operation requiring some readjustments, particularly during the first year of operation. Pages 28 and 29 refer to the limit and force adjustments. Only a screwdriver is required. Follow the instructions carefully . Repeat the safety reverse ...
-
Chamberlain PD210 -1/2 HP - page 34
34 Having a Problem? (Continued) 6. The garage door opens and closes by itself: • Be sure that all remote control push buttons are off. • Remove the bell wire from the door control terminals and operate from the remote only . If this solves the problem, the door control is faulty (replace), or there is an intermittent short on the wire between ...
-
Chamberlain PD210 -1/2 HP - page 35
LO C K L I G H T 35 *3-Button Remotes If provided with your garage door opener , the large button is factory programmed to operate it. Additional buttons on any Security ✚ ® 3-button remote or mini-remote can be programmed to operate other Security ✚ ® garage door openers. T o Erase All Codes From Motor Unit Memory T o deactivate any unwanted ...
-
Chamberlain PD210 -1/2 HP - page 36
36 LO C K L I G H T 1. Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER. 2. While holding the ENTER button, press and hold the LIGHT button on the Multi-Function Door Control. 3. Continue holding the ENTER and LIGHT buttons while you press the push bar on the Multi-Function Door Control ...
-
Chamberlain PD210 -1/2 HP - page 37
7 U P C E I L I N G M O U N T O N L Y 9 10 11 NOTICE 5 6 8 1 4 12 13 3 2 1 3 3 6 7 4 5 5 8 2 Installation Parts 37 REP AIR P ARTS Rail Assembly Parts KEY P ART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41A3489 Complete trolley assembly 3 183B1 12 Rail braces (each) 4 183B1 1 1 T -rail – center sections (each) 5 183B1 13 T -rail – end secti ...
-
Chamberlain PD210 -1/2 HP - page 38
Motor Unit Assembly Parts 38 2 10 8 13 14 15 19 4 5 3 9 16 12 18 11 17 1 6 7 DN UP Brown Wire (Down) Contact LIMIT SWITCH ASSY. Grey Wire Yellow Wire (Up) Contact Center Limit Contact Drive Gear KEY P ART NO. NO. DESCRIPTION 1 31D380 Sprocket cover 2 41C4220A Gear and sprocket assembly Complete with: Spring washer , Thrust washer , Retaining ring, ...
-
Chamberlain PD210 -1/2 HP - page 39
LOC K L I G H T L O C K LI GHT 39 ACCESSORIES SECURITY ✚ ® Multi-Function Remote Control: Includes visor clip. SECURITY ✚ ® Keyless Entry: Enables homeowner to operate garage door opener from outside by entering a password on a specially designed keyboard. Also can add a temporary password for visitors or service persons. This temporary passw ...
-
Chamberlain PD210 -1/2 HP - page 40
CHAMBERLAIN SER VICE IS ON CALL OUR LARGE SERVICE ORGANIZA TION SP ANS AMERICA INST ALLA TION AND SERVICE INFORMA TION IS AS NEAR AS YOUR TELEPHONE. SIMPL Y DIAL OUR TOLL FREE NUMBER: 1-800-528-9131 www .chamberlain-diy .com For professional installation, parts and service, contact your local CHAMBERLAIN dealer . Look for him in the Y ellow Pages, ...
У вас вопрос, касающийся Chamberlain PD210 -1/2 HP?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Chamberlain PD210 -1/2 HP, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Chamberlain PD210 -1/2 HP со всей вероятностью он захочет поделиться методом ее решения.