-
Xantrex Technology GT100E - page 1
GT100E MS Combiner Box for Master/Slave Configur ation Owner’ s Manual ...
-
Xantrex Technology GT100E - page 2
...
-
Xantrex Technology GT100E - page 3
GT100E MS Combiner Box for Master/Slave Configuration Owner’s Manual ...
-
Xantrex Technology GT100E - page 4
About Xantrex Xantrex T echnology Inc. is a worl d-leadin g supplier of advanced power electroni cs and controls with products from 50 watt mobile units to one MW utility-s cale systems for wi nd, solar , batteries, fuel cells, microturbines, and backup power applicati ons in bo th grid-connected and st and-alone systems. Xantrex products include i ...
-
Xantrex Technology GT100E - page 5
iii About This Manual Purpose The purpose of this Owner ’ s Manual is to provide explanat ion s and procedures for installing and configur ing the G T 100E MS Combiner Box for Master/Slave Configuration. Scope The Manual provides safety guidelines, procedures for installing the G T100E MS Combiner Box for Master/Slave Configuratio n, as well as i ...
-
Xantrex Technology GT100E - page 6
About T his Manual iv 152602 Conventions Used The following co nventions are used in thi s guide. Related Information Y ou can find more information about Xantrex T echnology Inc. as well as its products and services at www .xantrex.com WA R N I N G W arnings iden tify conditions or practices that could result in personal in jury or loss of life CA ...
-
Xantrex Technology GT100E - page 7
v Important Safety Instructions 1. Before installing and using th e G T100E MS Combiner Box for Master/Slave Configuration, read all instructions and cautionary markings on the G T100E MS Co mbiner Box for Master/Slave Configuration, G T 100E Grid T ie Inverter , and all appropriate sections of this manual. 2. Use only attachments recommended or so ...
-
Xantrex Technology GT100E - page 8
vi ...
-
Xantrex Technology GT100E - page 9
152602 vii Important Safety Instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - v 1 Introduction GT100E MS Combiner Box - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–2 Master/Slave Configuration - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–2 Mast ...
-
Xantrex Technology GT100E - page 10
viii ...
-
Xantrex Technology GT100E - page 11
152602 ix Figure 1-1 Configuration Diagram - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–4 Figure 2-1 GT100E MS Componenets - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–3 Figure 2-2 Wall Mounting Bracket Locations - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–4 Figure 2-3 Input/Output Acc ...
-
Xantrex Technology GT100E - page 12
x ...
-
Xantrex Technology GT100E - page 13
1 Intr oduction Chapter 1 contains a description of the G T100E MS and lists the different operating states available with the G T100E MS Combiner Box. ...
-
Xantrex Technology GT100E - page 14
Introduction 1–2 152602 GT100E MS Combiner Box The G T10 0E MS combiner box, when installed with dual G T100E s, allows the G T100E Master/Slave configuration to maximize energy production during periods of lo w irradiance. A system wou l d consist of two - 100kW inverters, one as the mast er and the other as a slave, and as a result, the G T100E ...
-
Xantrex Technology GT100E - page 15
Master/Slave Operation States 152602 1–3 If daily role reversal is on, then the configured slave is operational slave on odd days (Janua ry 1,3 ,5,...) and operational ma ster on even days (January 2,4,6,...). Master Unit The G T100E Master inverter will control the G T100E MS Combiner Box via a control cable. The Master invert er will enable and ...
-
Xantrex Technology GT100E - page 16
Introduction 1–4 152602 shutdown. The Master inverter will disable the Slave inverter and close the contactor in the G T 10 0E MS Combiner Box. The Master inverter will go online. F ault Condition If the Master or Sl ave Inverter g ets a fault or the status signal from either inverter is lost, the inverters will shutdown and restart as stand alon ...
-
Xantrex Technology GT100E - page 17
2 Installation Chapter 2 contains procedures on how to mount the G T100E MS and make the cable connections. ...
-
Xantrex Technology GT100E - page 18
Installation 2–2 152602 Equipment Required • Ratchet Handle • Extension • Metric socket set • Metric wrench set • Metric hex wrench set • T orque wrench with 0-150Nm minimum range • Phillips Screwdriver Unpacking the GT100E MS T o unpack the G T100E MS from the shipping pallet: 1. Remove the packing material from the MS100E. 2. Open ...
-
Xantrex Technology GT100E - page 19
Unpacking the GT100E MS 152602 2–3 Figure 2-1 GT100E MS Componenets Cable 1-152492-01 and 1-152493-01 Safety Cover M6 Mounting hardware GT100E MS interface assemblies and GT100E MS Combiner Box GT100E MS ...
-
Xantrex Technology GT100E - page 20
Installation 2–4 152602 Mounting Instructions T o mount the MS100E combiner box onto a wall: 1. Install the 4 wall mounting brackets P/N 062-200 0-02 to the rear of the MS100E Combiner box, see Figure 2-2. 2. Anchor the G T100E MS combiner box to the wall using anchor bolts. Important: The G T100E MS Combiner box needs to be moun ted with in 8 me ...
-
Xantrex Technology GT100E - page 21
Cable Installation 152602 2–5 Cable Installation W ire Gauge and T or que Specifications The following torque specifications ar e to be used on all electrical interfaces made during installati on of the G T100E MS Combiner Box. Wir e Gauge Requir ements for the GT100E MS Combiner Box One or multiple wires up to 300 mm 2 can be connected to the G ...
-
Xantrex Technology GT100E - page 22
Installation 2–6 152602 MS100E Connections Use the following descriptions and figures to correctly identify access panels and rou te wiring. Input/Output Access P anels Install all the cable strain reliefs, cust omer supplied, needed for cable entry in both Access Panels, see Figure 2-3. Figure 2-3 Input/Output Access P anel Location Input/Output ...
-
Xantrex Technology GT100E - page 23
Cable Installation 152602 2–7 PV Array and GT100E Connections Figure 2-4 PV Array and GT100E Connections PV ARRAY #1 and GT100E #1 Connections PV ARRAY #2 and GT100E #2 Connections ...
-
Xantrex Technology GT100E - page 24
Installation 2–8 152602 T o make PV Array #1 and G T 100E #1 connections : 1. Route the PV Array #1 cables through the access pa nel and connect the cables to PV ARRA Y #1 PV(+) and PV(-) terminals, see Figure 2- 5. 2. Route the G T100E #1 cables thr ough the access panel and connect the cables to G T 100E #1 PV(+) UNIT an d PV(-) terminals, see ...
-
Xantrex Technology GT100E - page 25
Cable Installation 152602 2–9 T o make PV Array #2 and G T 100E #2 connections : 1. Route the G T100E #2 cables thr ough the access panel and connect the cables to G T 100E UNIT #2 PV(+) an d PV(-) terminals, see Figure 2- 6. 2. Route the PV Array #2 cables through the access pa nel and connect the cables to PV ARRA Y #2 PV(+) and PV(-) terminals ...
-
Xantrex Technology GT100E - page 26
Installation 2–10 152602 GT100E MS Control P ower Cable T o make G T100E MS Control Power Cable connections: 1. Connect the G T100E MS com bin er bo x power cable assembl y P/N 1- 152492-01 from the G T100E #1 throug h the access panel and connect it to P1, see Figure 2-7. 2. Connect the G T100E MS com bin er bo x power cable assembl y P/N 1- 152 ...
-
Xantrex Technology GT100E - page 27
Cable Installation 152602 2–11 MS100E Interface Asse mbly Installation for GT100E #1 Mounting Instructions The G T 100E MS Interface is located in the bottom right compartment of the G T100E. See Figure 2-8. n Figure 2-8 Location of GT100E MS in the GT100E GT100E MS Interface Assemblies ...
-
Xantrex Technology GT100E - page 28
Installation 2–12 152602 T o install the G T100E MS Inte rfac e Assembly: 1. Mount the M S100E Interface Asse mbly to the Customer Interface Rail using the 4 supp lied T orx screws P/N 1-152173-01. See Figure 2-9. Figure 2-9 GT100E MS Interface As sembly Installation GT100E MS Interface Assembly Customer Interface Rail Torex Screws ...
-
Xantrex Technology GT100E - page 29
Cable Installation 152602 2–13 T o install the MS100E Interface Assembly Cable: 1. Connect the MS100E Interface A ssembly cable J20 to the G T100E Option Panel P20, located at the bottom/rear of the cabinet, see Figure 2-10. T o install the MS100E Control Power and Interface Cable: 1. Route the MS100E Power Ca ble assembly P/N 1-15 2492-01 and MS ...
-
Xantrex Technology GT100E - page 30
Installation 2–14 152602 T o install the MS100E Interface Assembly for G T100E #2: 1. Repeat the MS100E Interface Assemb ly Instructions for G T100E for the second G T100E unit - G T100E #2. GT100E Unit Installation T o install the G T100E refer to the G T 100E Grid T ie Inverter Installation Manual (P/N 152364). For G T100E commissioning or T ur ...
-
Xantrex Technology GT100E - page 31
3 Configur ation Chapter 3 describes how to configure the G T100E MS for Master/Slave configuration. ...
-
Xantrex Technology GT100E - page 32
Configuration 3–2 152602 Master/Slave Configuration The Master/Slave system can be c o nfigured through the Xantrex Solar GUI (Graphical User Inte rface) software, P/N 1-1 52577-01, or thro ugh the Operator Interface Panel. Establish remote or lo cal communication with the G T100E, us ing the Xantrex Solar GUI software. T o set a unit up as the M ...
-
Xantrex Technology GT100E - page 33
Master/Slave Configuration 152602 3–3 T o set a unit up as the Slave Unit: 1. Click T ools > Inverter Data > Operational Configuration 2. Check the Config ured Master check box Today’s status of the unit ...
-
Xantrex Technology GT100E - page 34
Configuration 3–4 152602 3. Click Send Configuration 4. V erify that the Present Inverter Da ta has the unit set as the Configured Slave unit. Refer to the GUI Help menu for complete conf iguration instructions. Important: If the inverter's date (not the workstat ion 's!) is odd then the Inverter is OPERA TIONAL SLA VE until midnight; i ...
-
Xantrex Technology GT100E - page 35
152602 WA–1 W arranty and Product Information Limited W arranty 1.1 What does this warranty cover and how long does it l ast? This Limited W arranty is provided by Xantrex T ech nolo gy In c. ("Xantrex") and covers defects in quality in workmanship and material s ("Defects") in your G T100E MS Com biner Box for Master/Slave Co ...
-
Xantrex Technology GT100E - page 36
W arranty and Return WA–2 152602 1.4 What does this warranty not cover? This Limited W arranty does not cover normal wear and tear of the product or costs associated with replacing consumable items such as li ke air filter, fuses, arrestors etc. A shorter than normal life dur ing the W arranty Period caused by excessive use, or inco rrect use not ...
-
Xantrex Technology GT100E - page 37
W arranty and Return 152602 WA–3 1.7 Exclusion for Documentation W ithout limiting the generality of the fo rego ing, unless specifically agreed to by it in writing, Xantrex: a. makes no warranty as to the accuracy , sufficiency or suitability of any t echnical or other informa- tion provided in manuals or oth er documentation prov ided by it in ...
-
Xantrex Technology GT100E - page 38
WA–4 ...
-
Xantrex Technology GT100E - page 39
...
-
Xantrex Technology GT100E - page 40
Xantrex Technology Inc. 1 800 670 0707 Tel toll free NA 1 360 925 5097 Tel direct 1 800 994 7828 Fax toll free NA 1 360 925 5143 Fax direct customerservice@xantrex.c om www.xantrex.com 152602 Printed in USA ...
У вас вопрос, касающийся Xantrex Technology GT100E?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Xantrex Technology GT100E, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Xantrex Technology GT100E со всей вероятностью он захочет поделиться методом ее решения.