-
Troy-Bilt 665B - page 1
Operator ’ s Manual Rear-tine T iller Model 665B Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush - covered or grass-covered land unless the engine ’ s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spa ...
-
Troy-Bilt 665B - page 2
2 For more details about your unit, visit our website at www .troybilt.com T ABLE OF CONTENTS Content Page Calling Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
-
Troy-Bilt 665B - page 3
Safety 1 Section 3 TRAINING 1. Carefully read this Owner’s Manual, the separate Engine Owner’s Manual, and any other literature you may receive. Be thor- oughly familiar with the controls and the proper use of the tiller and its engine. Know how to stop the unit and disengage the controls quickly. 2. Never allow children to operate the tiller. ...
-
Troy-Bilt 665B - page 4
4 Section 1: Safety 7. Take all possible precautions when leaving the machine unattended. Stop the engine. Disconnect spark plug wire and move it away from the spark plug. Move Wheel Gear Lever to ENGAGE. 8. Before cleaning, repairing, or inspect- ing, stop the engine and make certain all moving parts have stopped. Disconnect the spark plug wire an ...
-
Troy-Bilt 665B - page 5
Section 1: Safety 5 DECALS For your safety and the safety of others, various safety message decals are on your unit (see Figure 1-2). Keep the decals clean and legible at all times. Contact your local service dealer or the Factory for replacements if any decals are damaged or missing. Refer to the Parts List in this manual for decal locations, part ...
-
Troy-Bilt 665B - page 6
INTRODUCTION Carefully follow these assembly steps to correctly prepare your tiller for use. It is recommended that you read this Section in its entirety before beginning assembly. INSPECT UNIT Inspect the unit and carton for damage immediately after delivery. Contact the carrier (trucking company) if you find or suspect damage. Inform them of the ...
-
Troy-Bilt 665B - page 7
Section 2: Assembly 7 6. Thread the height adjustment screw (F, Figure 2-2) into the hole in the handlebar cross-brace, making sure that the raised keys on the washer fit into the slot on the height adjustment bracket. Tighten the height adjustment screw securely. Next, securely tighten the two screws and nuts in the ends of the handlebar (M, Figur ...
-
Troy-Bilt 665B - page 8
8 Section 2: Assembly STEP 5: CHECK TRANSMISSION GEAR OIL LEVEL The transmission was filled with gear oil at the factory. However, be sure to check the oil level at this time to make certain it is correct. IMPORTANT: Do not operate the tiller if the gear oil level is low. Doing so will result in severe damage to the transmis- sion components. 1. Wi ...
-
Troy-Bilt 665B - page 9
INTRODUCTION This section describes the location and function of the controls on your tiller. Refer to Section 4: Operation for detailed operating instructions. Practice using these controls, with the engine shut off, until you understand the operation of the controls and feel confi- dent with each of them. IMPORTANT: Refer to the separate engine m ...
-
Troy-Bilt 665B - page 10
10 Section 3: Features and Controls Moving the lever up increases the tilling depth. The lowest notch allows a tilling depth of approximately six to eight inches, depending on soil conditions. For best results, always begin tilling at a very shallow depth setting and gradually increase the tilling depth. Complete details on using the Depth Reg- ula ...
-
Troy-Bilt 665B - page 11
Operation 4 Section 11 INTRODUCTION Read this section of the manual thor- oughly before you start the engine. Then, take the time to familiarize yourself with the basic operation of the tiller before using it in the garden. Find an open, level area and practice using the tiller controls without the tines engaging the soil (put tines in “ travel ? ...
-
Troy-Bilt 665B - page 12
12 Section 4: Operation (b) Use the recoil starter rope to start the engine as instructed in the separate Engine Owner ’ s Manual. When the engine starts, gradually move the choke lever (if used) to the OPEN, CHOKE OFF or RUN position. (c) Put the engine throttle lever in the FAST setting when tilling. STOPPING THE ENGINE 1. To stop the wheels an ...
-
Troy-Bilt 665B - page 13
Section 4: Operation 13 Preparing Seedbeds Figure 4-6 Figure 4-7 • If the garden size will not permit lengthwise and then crosswise tilling, then overlap the first passes by one-half a tiller width, followed by successive passes at one- quarter width (see Figure 4-8). With planning, you can allow enough room between rows to cultivate (see Figure ...
-
Troy-Bilt 665B - page 14
14 Section 4: Operation TILLING TIPS & TECHNIQUES (cont.) Power composting simply means tilling under and burying in the soil all manner of organic matter such as crop residues, leaves, grass clippings and cover crops. This material will decompose during the non-growing season and add important natural nutri- ents to the soil. The first place t ...
-
Troy-Bilt 665B - page 15
Section 4: Operation 15 LOADING AND UNLOADING THE TILLER • Before loading or unloading, stop the engine, wait for all parts to stop moving, disconnect the spark plug wire and let the engine and muffler cool. Remove the ignition key on electric start models. • The tiller is too heavy (over 170 lbs.) and bulky to lift safely by one person. Two or ...
-
Troy-Bilt 665B - page 16
16 Maintenance 5 Section TILLER LUBRICA TION Proper lubrication of the tiller is an essen- tial part of your maintenance program. After every 10 operating hours, oil or grease the lubrication points shown in Figure 5-1, as described below. Use general purpose lubricating oil (#30 weight motor oil is suitable) and a general purpose grease (grease th ...
-
Troy-Bilt 665B - page 17
Section 5: Maintenance 17 2. Unscrew plastic gear oil fill plug from top of transmission. 3. Place a clean pan below the transmis- sion drain plug (see Figure 5-3) and then remove the drain plug. Oil will flow from the drain hole (it may flow slowly, espe- cially in cold temperatures). 4. Remove transmission gear oil level check plug located a few ...
-
Troy-Bilt 665B - page 18
18 Section 5: Maintenance wheels roll freely when the Wheel Gear Lever is in ENGAGE, the wheel gear cable needs to be adjusted as described below. 1. With engine shut off and spark plug wire disconnected, put Wheel Gear Lever in ENGAGE. 2. Loosen top adjustment nut (A, Figure 5-4) on wheel gear cable bracket located on left side rear of transmissio ...
-
Troy-Bilt 665B - page 19
Section 5: Maintenance 19 CHECKING AND ADJUSTING TENSION ON CLUTCH BEL TS Maintaining correct belt tension is impor- tant to good tilling performance and long belt life. A loose belt will slip on the engine and transmission pulleys and cause the tines and wheels to slow down – or stop – even though the engine is running at full speed. A loose b ...
-
Troy-Bilt 665B - page 20
20 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, remove ignition key on electric start models, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property dam ...
-
Troy-Bilt 665B - page 21
5. Slide the belt off the engine pulley (C, Figure 5-18), away from engine, out from under the belt guide (D), and completely off the pulley. 6. Slip the belt off the front of the trans- mission pulley (F, Figure 5-19). 7. Work the belt out from between the pulley and the frame, around the transmis- sion cover spring, then up and out of the machine ...
-
Troy-Bilt 665B - page 22
22 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, remove ignition key on electric start models, disconnect spark plug wire and move wire away from spark plug. Failure to follow these instructions can result in serious personal injury or property dam ...
-
Troy-Bilt 665B - page 23
Section 5: Maintenance 23 TROUBLESHOOTING Before performing any troubleshooting procedures, refer to the appropriate safety, operating or maintenance instructions in thi s Manual or in the Engine Owner ’ s Manual. Contact your local authorized engine service dealer for engine service. Contact your local authorized tiller dealer or the factory for ...
-
Troy-Bilt 665B - page 24
24 Parts List Model 665B DRA WING NO. 1 10 ...
-
Troy-Bilt 665B - page 25
Parts List 25 Model 665B REF PART No. No. DESCRIPTION QTY. REF PART No. No. DESCRIPTION QTY. 1 1918791 Handlebars – (Incl. Refs. 2, 3 and 3A) ... 1 2 GW-9126 Grip ..................................................... 2 3 777I20939 Decal – Operator control panel .............. 1 3A 777D05554 Decal – Logo ....................................... ...
-
Troy-Bilt 665B - page 26
26 Parts List Model 665B 1 1917143 Hood – Tine cover, with hinged flap (Incl. Ref. 17) .................................. 1 2 736-0169 Lockwasher, 3/8.................................. 2 3 GW-2527 Bracket – Hood & Depth Regulator (Incl. Ref. 9) ................................... 1 4 1186328 Screw – flanged hex hd., 5/16-18 x 5/8* 2 5 712 ...
-
Troy-Bilt 665B - page 27
Parts List 27 Model 665B 1 GW-9621 Oil Seal .............................................. 2 2 1909950 Ring – Retaining, heavy-duty, ext. ....... 2 3 GW-1166-1 Shim – 1-1/64 I.D., .062 thick ............. A/R --- GW-1166-2 Shim – as above, but .030 thick .......... A/R --- GW-1166-3 Shim – as above, but .015 thick .......... A/R --- GW-1166 ...
-
Troy-Bilt 665B - page 28
28 Parts List Model 665B DRA WING NO. 4 Reverse Clutch Cable 1 2 6 5 7 3 4 13 14 15 16 17 16 52 21 25 24 39 45 46 20 49 50 51 43 43 44 37 47 37 40 42 48 41 54 53 44 38 35 20 23 8 12 26 27 3 28 29 30 31 9 22 18 45 12 11 20 10 9 8 35 36 ...
-
Troy-Bilt 665B - page 29
Parts List 29 Model 665B P ARTS LIST - DRA WING NO. 4 * Specify GRADE 5 if ordering part locally. ** See your local authorized engine service dealer for engine parts or service. Refer to engine nameplate for engine type and code information. 1 ** Engine – standard recoil start ............ 1 2 1917326 Bracket, Clutch Cable ....................... ...
-
Troy-Bilt 665B - page 30
30 Parts List Model 665B MAIN DRIVE SHAFT ASSEMBL Y 1 GW-1714 Bearing – Tapered roller with race ............ 1 2 GW-20718 Gear – Spur, main drive shaft ................... 1 3 GW-9301 Key, 3/16 sq. x 1 ..................................... 1 4 GW-11603 Drive Shaft – with integral, single-lead worm at front and six-lead worm at rear (includes ...
-
Troy-Bilt 665B - page 31
Parts List 31 Model 665B 1 710-3105 Hex Hd. Screw, 3/8-16 x 1-1/4*................... 16 2 GW-1270-2A Bolo Tine – single, right hand tine used on left side of tiller (Incl. two of each Ref. No.'s 1 and 3)...................................................... 8 3 712-0375 Hex Locknut, 3/8-16 .................................... 2 5 710-3096 H ...
-
Troy-Bilt 665B - page 32
32 Parts List Model 665B DRA WING NO. 7 19 20 23 22 21 BUMPER OEM-290-254 HILLER/FURROWER ATTACHMENT (option) OEM-290-251 (Viewed from front of tiller) ROW MARKER ATTACHMENT (option) – OEM-290-257 (Complete – Attaches to Furrower Attachment) MAIN SUPPORT & YOKE ASSEMBLY PART # 1904522001 (See Detail A) Detail A ...
-
Troy-Bilt 665B - page 33
Parts List 33 Model 665B Row Marker Attachment (option) – OEM-290-257 1 1904522 Main Support & Yoke Assy – complete. Incl. Ref. No.'s 10,11,12,13,14,15,16,17 & 18 ........... 1 2 GW-1594 Marker Blade – blade only ................... 1 3 1904524 Marker Arm – main arm ...................... 1 4 1904523 Marker Arm – extension ar ...
-
Troy-Bilt 665B - page 34
34 Parts List Model 665B DRA WING NO. 8 NOTE 1: These screws are a special sealing screw that cannot be reused without risking the loss of transmission oil. If these screws are loosened or removed, they must be replaced with new hardware. * Specify GRADE 5 if ordering part locally. A/R – As Required 1 GW-9621 Oil Seal – double lip, wheel shaft ...
-
Troy-Bilt 665B - page 35
NOTES 35 ...
-
Troy-Bilt 665B - page 36
TROY -BIL T TILLER LIFETIME LIMITED W ARRANTY WHAT PRODUCT All Troy-Bilt branded rear tine walk-behind tillers with gear drive transmissions. IS COVERED This warranty begins on the date of purchase and is warranted by Troy-Bilt LLC for the life of the tiller, to the original purchaser only. WHAT IS COVERED Troy-Bilt LLC will, at its option, repair ...
У вас вопрос, касающийся Troy-Bilt 665B?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Troy-Bilt 665B, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Troy-Bilt 665B со всей вероятностью он захочет поделиться методом ее решения.