-
Frymaster SDU 90 - page 1
Frymaster, a member of the Comm ercial Food Equipment Service Association, recommends using CFESA Certified Technicians. 24-Hour Service Hotline 1-800-551-8633 MARCH 11 www.frymaster.com E-mail: service@frymaster.com *8195703* Shortening Disposal Unit (SDU 50, 90, 100 and BKSDU) Installation, Operation, Service and Parts Manual ...
-
Frymaster SDU 90 - page 2
ii NOTICE IF, DURING THE WARRANTY PERIOD, THE CU STOMER USES A PART FOR THIS ENODIS EQUIPMENT OTHE R THAN AN UNMODIFIED NEW OR RECYCLED PART PURCHASED DIRECTLY FROM FRYMASTER DEAN, OR AN Y OF ITS AUTHORIZED SERVICE CENTERS, AND/OR THE PART BEI NG USED IS MODIFIED FROM ITS ORIGINAL CONFIGURATION, THIS WARRANTY WILL BE VOID. FURTHER, FRYMASTER DEAN A ...
-
Frymaster SDU 90 - page 3
iii Shortening Disposal Unit (SDU) Installation, Operation, Service, and Parts Manual TABLE OF CONTENTS Page 1. INTRODUCTION 1 1.1 Service Information and Parts Ordering ..............................................1 1.2 Installation, Operating and Service Personnel .....................................1 1.3 Definitions ........................... ...
-
Frymaster SDU 90 - page 4
SHORTENING DISPOSAL UNIT (SDU 100, 90 50, AND BKSDU) INSTALLATION, OPERATION, SERVICE AND PARTS 1 1. INTRODUCTION 1.1 Service Information and Parts Ordering Included with the unit when shipped from the fact ory is a list of Factor y Authorized Servicers (FAS). Refer to this list to fi nd the FAS nearest you. If you do not have access to this list, ...
-
Frymaster SDU 90 - page 5
2 manuals, and to stock a minimum amount of parts for F rymaster equipment. A list of Factory Authorized Service Centers (FAS s) was included with this equipm ent when shipped from the factory. Unless specifically indica ted ot herwise in this manual, failure to use q ualified service personnel will void the Frymaster Warranty on this equipment. 1. ...
-
Frymaster SDU 90 - page 6
3 2.2 Equipment Assembly Assembly of the unit is a four-step process: 1. Remove the two bolts from the handle-mounting bracket and raise the handle to the upright position. Reinstall the bolts in th e bracket and tighten to 8 ft/lbs. 2. Ensure the O-rings and the bottom 2 inches of the suction tube are lubricated with Accrolube with Teflon or an eq ...
-
Frymaster SDU 90 - page 7
4 DANGER DO NOT OVERFILL! Do not f ill the reservoir above the fill lines on the sides of the reservoir. Moving the SDU with an overfilled reservoir may result in spills and injury to personnel who come in contact with the spilled shortening. 4. Carefully withdraw the unit far en ough to allow the cover to be cl osed. Latch the cover in the closed ...
-
Frymaster SDU 90 - page 8
5 WARNING DO NOT clean the interior of the reservoir with water or detergent. Introduction of water or detergent into the unit w ill perma nently damage the pump. 3. SERVICE PROCEDURES 3.1 Introduction Other than routine cleaning and the replacement of worn suction tube O-rings, the SDU is maintenance free. After long use, the pum p vane s and pump ...
-
Frymaster SDU 90 - page 9
6 Step 5 - Replace gask et. Step 1 - Loosen setscre w an d remove handle. Step 2 - Rem ove cover screws and c over. Step 3 - Grasp shaf t an d pull roto r asse mbly out of housing. Step 4 - Replace vanes, spring, and rod. Pump sh aft sea l fits in to th e rece ss of th e p ump cov er . 4. Assemble the replacement vanes, spring and rod into the ro t ...
-
Frymaster SDU 90 - page 10
7 4. PARTS LIST 1 2 6 5 4 3 8 10 9 7 13 12 11 14 15 16 17 18 SDU 50, 90, 100 and BKSDU units built April 2010 and later. ...
-
Frymaster SDU 90 - page 11
8 Item Part # Component 1 810-3784 Wheel, 6” x 2” 2 809-0200 Washer, flat, ½” 3 809-1001 Screw, ¼ x 20 x ½” 4 823-2421 Handle, SDU 90, 100 * 823-2038 Handle, SDU 50, BKSDU 5 810-0777 Spring-loaded plunger 6 810-3858 Check valve, ¾” NPT (Added August 2010) 7 813-0032 Bushing, hex 1 x 3/4 8 810-0657 Pump handle 9 813-0109 Nipple, ¾ NPT ...
-
Frymaster SDU 90 - page 12
9 5 17 22 23 32 31 33 9 28 1 2 3 4 6 7 8 10 12 13 11 14 15 16 20 21 25 26 27 29 16 11 30 18 34 38 37 36 35 19 NOTE: Se e Page 6 for BKSDU pump assembly compo nents. 24 (Crumb Ba sket optional ) SDU 50, 90, 100 and BKSDU units built before April 2010. ...
-
Frymaster SDU 90 - page 13
10 Item Part # Component 1 Pipe Assembly, Discharge 823-4600 Standard (includes Item 2) (use 823-4617 for BKSDU) 823-4598 For use with Item 4 (Hose Discharge) (includes Item 3) 2 813-0115 Nipple, ¾-inch x 3-inch Toe 3 813-0031 Bushing, ¾-inch x ½-inch 4 810-1845 Hose, 24-inch Discharge (Optional) (use 810-2797 for 48-inch hose) 5 813-0109 Nipple ...
-
Frymaster SDU 90 - page 14
11 NOTE: T he BKSDU pum p assem bly is identical to the SDU 50/SDU 90 pum p as sem bly except for the addition of the pump c over and insulatio n and t he m odified dischar ge pipe ass em bly. 1 2 3 4 5 6 6 ITEM PART # COMPONENT 1 823-1847 Cover and Handle Assembly, BKSDU 2 900-4429 Box, BKSDU Pump 3 811-0861 Insulation, 3-inch X 50 -foot Adhesive- ...
-
Frymaster SDU 90 - page 15
...
-
Frymaster SDU 90 - page 16
Frymaster, L.L.C., 8700 Line Av enue, Shrev eport, Louisiana 71106 TEL 1-318-865-1711 FAX (Par ts) 1-318- 688-2200 FAX (Tech Support) 1-318-219-7135 PRINTED IN THE UNITED STATES SERVICE HOTLINE 1-800-551-8633 819-5703 March 2011 ...
У вас вопрос, касающийся Frymaster SDU 90?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Frymaster SDU 90, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Frymaster SDU 90 со всей вероятностью он захочет поделиться методом ее решения.