-
Wilton 2221VS - page 1
Operating Instructions — Parts Manual 20-Inch VS Drill Press Models: 2221VS, 2223VS, 2232AC, 2234AC Serial Number 201001 and greater WHM TOOL GROUP 2420 V antage Drive Elgin, Illinois 60124 Part No. 5510374 Ph.: 800-274-6848 Revision D6 08/06 www .wmhtoolgroup.com Copyright © WMH T ool Group ...
-
Wilton 2221VS - page 2
...
-
Wilton 2221VS - page 3
3 T able of Content s Cover Page ....................................................................................................... 1 General S pecifications ...................................................................................... 4 Operating Precautions ............................................................................ ...
-
Wilton 2221VS - page 4
4 General S pecifications The Wilton 20 Inch V ariable S peed Drill presses Models 2221VS, 2223VS, 2232AC, and 2234AC are available in manual speed control or inverter speed control configuration. Electrical power options are single-phase, 1 15 and 220 volts, or 3-phase, 440 volts. S pecifications Manual Speed Control Models Inverter Speed Control ...
-
Wilton 2221VS - page 5
5 supply while servicing. - Always follow instructions in Operating Instructions and Parts Manual when changing accessory tools or parts. - Never modify the machine without consulting Wilton Corporation. Y ou—the st ationary power tool user— hold the key to safety . Read and follow these simple rules for best results and full benefits from your ...
-
Wilton 2221VS - page 6
6 A WG (American wire gauge) number Conductor length 240 volt lines 120 volt lines 0-50 feet No. 14 No. 14 50-100 feet No. 14 No. 12 Over 100 feet No. 12 No.8 General electrical cautions This drill press should be grounded in accordance with the National Electrical Code and local codes and ordinances. This work should be done by a qualified electri ...
-
Wilton 2221VS - page 7
7 Introduction This manual includes operating and maintenance instructions for the Wilton Model 2221VS, 2223VS, 2232AC and 2234AC V ariable S peed Drill Presses. This manual also includes parts listings and illustra- tions of replaceable parts. Wilton Model 2221VS and 2223VS drill presses feature manual speed control. Models 2232AC and 2234AC have ...
-
Wilton 2221VS - page 8
8 Raising the Drill Head and T able The drill press is shipped with the table and drill head supported by wooden blocks near the bottom of the column. The head is raised to the operating position using a strap and hoist, then secured to the column by tighening the hex cap screw . The table is raised to the desired position using the crank handle. E ...
-
Wilton 2221VS - page 9
9 Figure 4: Control Panel (Inverter Speed Control) Drilling Speed Chart A DRILLING SPEED CHART is provided on the front panel. The chart can be used to select the speed required for various drill sizes (0.196 inch to 1.000 inch — 5 mm to 25 mm) and materials (steel, cast iron, aluminum, and copper). The chart defines spindle speeds from 300 to 30 ...
-
Wilton 2221VS - page 10
10 Replacement of Drive Belt W ARNING: MAKE SURE TO DISCONNECT ELECTRICAL POWER TO THE DRILL PRESS TO A VOID THE POSSIBILITY OF INADVERTENT OPERA TION AND EXPOSURE T O POTENTIALL Y LETHAL VOL T AGE LEVELS. Manual Speed Control - Models 2221VS and 2223VS 1. S tart drill press. Set speed control to highest speed. S top drill press. 2. Disconnect elec ...
-
Wilton 2221VS - page 11
11 W ARNING: CHANGE THE RADIAL POSITION OF THE DRILL HEAD ONL Y IF THE DRILL PRESS BASE IS SECURED TO THE FLOOR. SWINGING THE DRILL HEAD WITHOUT THE BASE BEING SECURED TO THE FLOOR WILL CAUSE THE DRILL PRESS T O BECOME UNST ABLE AND TIP OVER RESUL TING IN INJUR Y AND/OR DAMAGE TO THE MACHINE. Radial Adjustment of Head (All Models) The radial positi ...
-
Wilton 2221VS - page 12
12 Feeds for Drilling The feed of a drill is governed by the size of the tool and the material drilled. Because the feed rate partially determines the rate of production and also is a factor in tool life, it should be chosen carefully for each job. In general, the most effective feeds will be found in the following ranges: Diameter of Drill Feed pe ...
-
Wilton 2221VS - page 13
13 Wiring Diagram - Models 2221 & 2223 ...
-
Wilton 2221VS - page 14
14 Wiring Diagram - Models 2232AC & 2234AC LED Display Connection 0 220 AC Power Sensor V olts - + Input 3 Phase 220/440 ...
-
Wilton 2221VS - page 15
15 T roubleshooting Problem Possible Cause Remedy S pindle does not turn. 1. Motor overload protector tripped. 1. Press motor overload reset button. 2. Circuit breaker tripped. 2. Reset circuit breaker . 3 . Branch circuit breaker tripped or fuse blown. 3. Reset branch circuit breaker/replace fuse. 4 . Open wire in switch circuit. 4 . Repair open c ...
-
Wilton 2221VS - page 16
16 Optional Equipment Coolant System Installation 1. Remove the large reservoir cover plate from the machine base. T ap 1/4-20 threads in the 4 pilot holes. Install the cover plate back onto the machine base. 2. Insert the pump into the opening, utilize the screws from the small round cover plate to fasten the pump to the base. 3. Position the powe ...
-
Wilton 2221VS - page 17
17 Replacement Part s This section provides exploded view illustrations that show the replacement parts for Wilton Model 2221VS, 2223VS, 2232AC, and 2234AC 20-Inch Drill Presses. Also provided are parts listings that provide part number , description, and quantity . The item numbers shown on the illustration relate to the item number in the facing ...
-
Wilton 2221VS - page 18
18 Exploded V iew — Drill Head — Manual S peed Control (Models 2221VS and 2223VS) ...
-
Wilton 2221VS - page 19
19 7 5510077 Pulley , S pindle S tep 1 8 5510078 Nut, S pindle 1 9 5510079 V -Belt 1 10 5510080 Pulley , S pindle, VS, Lower 1 1 1 5510081 Pulley , S pindle, VS, Upper 1 1 1A 5513673 Screw , Cap 1 1 1B 5513674 Nut, Hex 4 12 5510082 Bearing, Ball 1 13 5510083 Cover , Bearing 1 14 5510084 Lever , S peed Change 1 15 5510085 Bearing, Ball 2 16 5510086 ...
-
Wilton 2221VS - page 20
20 Exploded View — Drill Head — Inverter S peed Control (Models 2232AC and 2234AC) ...
-
Wilton 2221VS - page 21
21 Item Part No. Number Description Qt y 1 5517332 Casting, Head 1 2 5510142 W indow , Oil 1 3 5510143 Bearing, Ball 1 4 5510144 Ring, Retaining 1 5 5510145 Gear (32T) 1 6 5510146 Key 1 7 5510147 Shaft, Drive (13T) 1 8 5510148 Bearing, Ball 1 9 5510149 Ring, Retaining 1 10 5510150 Bearing, Ball 1 1 1 5510151 Ring, Retaining 1 12 5510153 Gear (55T) ...
-
Wilton 2221VS - page 22
22 Item Part No. Number Description Qt y 85-1 5517371 W asher , Flat 4 85-2 5517372 Screw 4 86 5517373 Sub-Panel 1 86-1 5517374 Screw 4 87 5510235 T erminal Block 1 88 5517375 Rail, Mounting 1 89 5510237 Contactor 1 89-1 5510238 Relay 1 90 5510240 Relay 1 94 5510242 Screw 2 95 5510243 Screw 2 96 5510244 Microswitch 2 97 5510245 Bracket, Microswitch ...
-
Wilton 2221VS - page 23
23 Exploded View — S pindle Components (All Models) ...
-
Wilton 2221VS - page 24
24 Item Part No. Number Description Qt y 1 5517332 Casting, Head 1 2 5517376 Bolt, Hex, Shoulder 2 2- 1 5517377 S pring 2 3 5517378 Rod, Cam Lock 2 4 5510250 Nut, Hex 2 5 5510251 Wrench, Hex Head 1 7 5510252 Screw , Set 1 8 5517379 W asher , External T ooth 1 10 5510253 S pindle 1 1 1 5510254 Bearing, Ball 2 12 5510255 S p acer 1 14 5510256 C-Ring ...
-
Wilton 2221VS - page 25
25 Exploded View - T able and Base (All Models) ...
-
Wilton 2221VS - page 26
26 Item Part No. Number Description Qt y 1 5510288 Base 1 2 5510289 Plate, Coolant Cover 1 3 5510456 Pump, Coolant, 1 15V , 1P 1 5512103 Pump, Coolant, 220/440V 3P 1 4 5510291 Bolt, Hex 4 5 5517388 Screw , Pan Head 3 6 5510293 Seat, Ball 1 7 5510294 Screw , Set 4 7- 1 5517389 Block, Brass 4 8 5510295 Bearing, Ball 1 9 5510296 Ring, Lock 1 9- 1 5517 ...
-
Wilton 2221VS - page 27
...
-
Wilton 2221VS - page 28
WMH TOOL GROUP 2420 V antage Drive Elgin, IL 60123 Phone: 800-274-6848 ...
У вас вопрос, касающийся Wilton 2221VS?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Wilton 2221VS, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Wilton 2221VS со всей вероятностью он захочет поделиться методом ее решения.