-
Eva Solo LX-90TM - page 1
EPSON ® LX-90 TM PRINTER User’s Manual ...
-
Eva Solo LX-90TM - page 2
FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computi ...
-
Eva Solo LX-90TM - page 3
Contents Setting Up Your LX-90 Printer ....................... . 1 Do You Have All the Parts You Need? ................ . 1 Where to Place Your Printer ........................ . 2 Installing the Ribbon .............................. . 3 Plugging in the Cartridge ........................... . 5 Installing the Paper Feed Knob ...................... ...
-
Eva Solo LX-90TM - page 4
Setting Up Your LX-90 ™ Printer Setting up your LX-90 printer is easy, even if you’ve never used a printer before. By following the instructions in this manual, you’ll have your new printer ready to go in just a few minutes. Do You Have All the Parts You Need? When you unpack your printer, be sure that the box contains all of the items shown: ...
-
Eva Solo LX-90TM - page 5
Where to Place Your Printer Now that your printer is unpacked, you need to find the best place to put it. Keep the following tips in mind: l Place the printer close enough to the computer for the PIC cable to reach between them. l Place the printer on a stable surface. Avoid setting the LX-90 on carpeting or chairs. l Use a grounded outlet, and do ...
-
Eva Solo LX-90TM - page 6
Many types of printer stands are available; the previous illustration shows one type. The next illustration shows a setup that does not require a stand. These are only two examples; you can use any arrangement that allows you to put the paper underneath or behind the printer. Once you’ve found the right location for your new LX-90, you’re ready ...
-
Eva Solo LX-90TM - page 7
To install or replace the ribbon, just follow these steps: Caution If you’ve been using your printer just before you change rib- bon cassettes, be careful not to touch the print head because it becomes hot during use. Also remember never to move the ribbon carriage manually when the printer is turned on, because you may damage your printer. 1. Ma ...
-
Eva Solo LX-90TM - page 8
5. Snap the cassette into place so that the exposed ribbon fits between the print head and the silver ribbon guide. 6. Now turn the knob on the cassette in the direction of the arrow to tighten the ribbon. As you turn the knob, make sure the ribbon slips down into its proper place between the print head and the silver ribbon guide. If it doesn’t, ...
-
Eva Solo LX-90TM - page 9
Hold the cartridge with the grooved side facing down. Insert the cartridge into the opening and press gently to secure the connection. Do not connect the PIC cable to your computer yet. The instruc- tions for this connection are in your PIC manual. Installing the Paper Feed Knob Before you can load paper into your LX-90, you need to install the pap ...
-
Eva Solo LX-90TM - page 10
With the paper feed knob in place, you’re now ready to load paper into your printer. If you plan to use continuous paper, read the next two sections. For instructions on single-sheet paper, skip to the section on loading single-sheet paper. Installing the Paper Separator To install the paper separator, fit the notches in the bottom comers of the ...
-
Eva Solo LX-90TM - page 11
Make sure that the printer is turned off; then open the front lid. Move the print head to the center of the printer, and pull the paper bail away from the platen (the black roller). Using the illustration below as your guide, pull the locking levers forward so that you can move the pin feed holders to the left and right. Put the left holder approxi ...
-
Eva Solo LX-90TM - page 12
Open the pin feed covers as shown on the previous page and feed the paper under the paper separator and into the paper slot. Push the paper through until it comes up between the ribbon guide and the platen. Pull the paper up until the top is above the pin-feed holders; fit the holes on the left side of the paper over the pins in the left holder; th ...
-
Eva Solo LX-90TM - page 13
If you are using a word processing or other applications program and your printing is too high or too low on the page, change your top of page setting. Once you have set the top of page, each time you finish printing a document, push the ON LINE button to put the printer off-line and then push the FF button once to advance the paper so that you can ...
-
Eva Solo LX-90TM - page 14
Loading Single-Sheet Paper 1. First, make sure that the printer is turned OFF. Open the front lid, push the friction lever back, and pull the paper bail forward. 2. Now slide the ribbon carriage manually to the center of the printer and feed the paper into the paper slot in the top of the printer as shown below. Friction lever Front lid 3. When the ...
-
Eva Solo LX-90TM - page 15
Replacing the Tractor Unit Replacing the tractor after you have removed it is easy. Pull the friction lever on the left side of the printer toward you, and hold the tractor with the gears to the right as shown below. I I Tilt the tractor back so that the rear notches on the fittings fit over the rear pegs in the tractor slots; then tilt the unit fo ...
-
Eva Solo LX-90TM - page 16
Maintenance To keep your LX-90 working like new, always keep it in a safe and clean place. Keep it away from dust, grease, and any heat sources. A safe temperature range is 41°F to 95°F. To clean the outside of the printer case, use a soft, clean cloth damp- ened with clear water. Stubborn stains can be removed with non-abra- sive household clean ...
-
Eva Solo LX-90TM - page 17
Specifications Printing method ......... . Impact dot matrix Printing speed ........... . 100 characters per second per line in pica draft mode Printing direction ........ . Bidirectional, logic seeking Ribbon ................. . Cassette ribbon, black Height (with tractor) ...... . 5.1 inches Width .................. . 16.6 inches Depth (with pape ...
-
Eva Solo LX-90TM - page 18
EPSON AMERICA, INC. LIMITED WARRANTY Epson America, Inc. hereby warrants that it will repair or replace, at its option, any part of the Epson product with which this warranty is enclosed which proves defective by reason of improper workmanship and/or material, without charge for parts or labor, for a period of one (1) year. This warranty period com ...
У вас вопрос, касающийся Eva Solo LX-90TM?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Eva Solo LX-90TM, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Eva Solo LX-90TM со всей вероятностью он захочет поделиться методом ее решения.