Инструкция обслуживания Thomas & Betts RZ-NA 441-OMS

12 страниц 1.36 mb
Скачать

Перейти на страницу of 12

Summary
  • Thomas & Betts RZ-NA 441-OMS - page 1

    Page 1 FOR YOUR SAFETY W ARNING: The use and storage of gasoline or other flammable vapors and liquids in the vicinity of this appliance is hazardous. If you smell gas: 1. Open windows. 2. Don't touch electrical switches. 3. Extinguish any open flame. 4. Immediately call your gas supplier . W ARNING: Improper installation, adjustment, alterati ...

  • Thomas & Betts RZ-NA 441-OMS - page 2

    Page 2 Maintenance Section This direct-fired makeup air system is designed to require only a minimum amount of maintenance. Some maintenance procedures outlined in this Section require inspection only and some require action. Frequency requirements of each maintenance procedure are listed in the Maintenance Schedule. Depending on the environment an ...

  • Thomas & Betts RZ-NA 441-OMS - page 3

    Page 3 Inlet Pressur e T ap V alve V alve Regulator Manifold Pressure T ap Gas Supply Pilot Regulator Pilot Solenoid V alve Pilot Pressur e T ap 3. Manifold Gas Pressure Semiannually , check the gas pressure to the burner and to the pilot. Measure both manifold pressure and pilot supply pressure w ith the blower in operation. Refer to Figure 3 for ...

  • Thomas & Betts RZ-NA 441-OMS - page 4

    Page 4 4. Air Pressure Profile plate sensing tubes should be checked quarterly and cleaned no less than semiannually . If the sensing tubes become even partially blocked, false pressure readings may be relayed. T o clean, remove the screened end caps. Clean the screens and the tubes, if necessary . Re- place the cleaned end caps. Check the pressure ...

  • Thomas & Betts RZ-NA 441-OMS - page 5

    Page 5 Operation/Service Section Controls - Location, Operation, and Service T o service this system, it is necessary to understand the normal operation of the controls and the function of the diagnostic circuit board. Refer to the electrical box drawing in Figure 7 and to the individual illustrations to identify and locate each of the controls. Th ...

  • Thomas & Betts RZ-NA 441-OMS - page 6

    Page 6 10. Ignition System Location: Ignition Controller Module in the Control Compartment Electrical Box (See Figures 7 and 13.); Ignitor and Flame Sensor on the Burner (See Figure 14.) Hot Surface Ignition System with Prepurge Time Delay and Flame Sensor with 100% Lockout Function: The ignition system including the controller, the hot surface ign ...

  • Thomas & Betts RZ-NA 441-OMS - page 7

    Page 7 For troubleshooting guides and further explanation of Maxitrol Series 14 and 44 electronic modulation gas control systems, refer to the Maxitrol literature in the owner's envelope. The Option AG30, AG31, AG32 and AG35 electronic modulation systems are comprised of Maxitrol Series 14 controls. Options AG30 and AG31 systems electronically ...

  • Thomas & Betts RZ-NA 441-OMS - page 8

    Page 8 12. Outside Air Cutoff Control (Option BN2; required on C.G.A.-certified units) Location: The control is in the electrical box (See Figure 7.); the sensor is in the air inlet. Function: After sensing pilot flame, the burner ignites at its lowest input rate. The "amount of heat" required to reach the de- sired discharge temperature ...

  • Thomas & Betts RZ-NA 441-OMS - page 9

    Page 9 13. Door Switch (Option BX1; required on C.G.A.-certified units) Location: The control is installed on an over- head door opening to control the operation of the heater to coincide with the opening and clos- ing of the door . Function: The function of the switch is to ener- gize and interlock the heating unit when an out- side overhead door ...

  • Thomas & Betts RZ-NA 441-OMS - page 10

    Page 10 15. Dirty Filter Switch Location: Switch is located in the main electrical box (See Figure 7); sensor tubes run to either side of the filter rack; indicator light is on the remote console. Function: The dirty filter switch is a pressure switch that activates an indicator light on the remote console when the filters need cleaned or replaced ...

  • Thomas & Betts RZ-NA 441-OMS - page 11

    Page 11 19. T roubleshooting Chart 1 - General T roubleshooting Guide (Check the diagnostic lights on the circuit board) Sym p tom or P r ob l e m C au s e an d R e m e d y 1. Disconnec t s wit ch i s cl osed, but " control p ow e r" lig ht is not l it . 1. F us e s are mi s s i ng or bl own in disconne ct sw i t ch - rep l ace fu s es . ...

  • Thomas & Betts RZ-NA 441-OMS - page 12

    Page 12 Index .................................................. Page Air Pressure ............................................. 4 Air Pressure Switches ............................... 6 Blower Bearings ....................................... 3 Circuit Indicator Board ............................ 4 Control Locations ................................ ...

Производитель Thomas & Betts Категория Appliance Trim Kit

Документы, которые мы получаем от производителя устройства Thomas & Betts RZ-NA 441-OMS мы можем разделить на несколько групп. Это в частности:
- технические чертежи Thomas & Betts
- инструкции обслуживания RZ-NA 441-OMS
- паспорта изделия Thomas & Betts
- информационные брошюры
- энергетические этикетки Thomas & Betts RZ-NA 441-OMS
Все из них важны, однако самую важную информацию с точки зрения пользователя мы найдем в инструкции обслуживания Thomas & Betts RZ-NA 441-OMS.

Группа документов, определяемая как инструкции обслуживания, делится также на более подробные типы, такие как: Инструкции монтажа Thomas & Betts RZ-NA 441-OMS, инструкции обслуживания, короткие инструкции или инструкции пользователя Thomas & Betts RZ-NA 441-OMS. В зависимости от потребностей, Вам необходимо поискать требуемый документ. На нашем сайте Вы можете просмотреть самую популярную инструкцию использования изделия Thomas & Betts RZ-NA 441-OMS.

Похожие инструкции обслуживания

Полная инструкция обслуживания устройства Thomas & Betts RZ-NA 441-OMS, как должна выглядеть?
Инструкция обслуживания, определяемая также как пособие пользователя, или просто "руководство" - это технический документ, цель которого заключается в использовании Thomas & Betts RZ-NA 441-OMS пользователями. Инструкции пишет, как правило технический писатель, языком, доступным для всех пользователей Thomas & Betts RZ-NA 441-OMS.

Полная инструкция обслуживания Thomas & Betts, должна заключать несколько основных элементов. Часть из них менее важная, как например: обложка / титульный лист или авторские страницы. Однако остальная часть, должна дать нам важную с точки зрения пользователя информацию.

1. Вступление и рекомендации, как пользоваться инструкцией Thomas & Betts RZ-NA 441-OMS - В начале каждой инструкции, необходимо найти указания, как пользоваться данным пособием. Здесь должна находится информация, касающаяся местонахождения содержания Thomas & Betts RZ-NA 441-OMS, FAQ и самых распространенных проблем - то есть мест, которые чаще всего ищут пользователи в каждой инструкции обслуживания
2. Содержание - индекс всех советов, касающихся Thomas & Betts RZ-NA 441-OMS, которое найдем в данном документе
3. Советы по использованию основных функций устройства Thomas & Betts RZ-NA 441-OMS - которые должны облегчить нам первые шаги во время использования Thomas & Betts RZ-NA 441-OMS
4. Troubleshooting - систематизированный ряд действия, который поможет нам диагностировать а в дальнейшем очередность решения важнейших проблем Thomas & Betts RZ-NA 441-OMS
5. FAQ - чаще всего задаваемые вопросы
6. Контактные данные Информация о том, где искать контактные данные производителя / сервисного центра Thomas & Betts RZ-NA 441-OMS в данной стране, если самостоятельно не получится решить проблему.

У вас вопрос, касающийся Thomas & Betts RZ-NA 441-OMS?

Воспользуйтесь формуляром, находящимся ниже

Если с помощью найденной инструкции Вы не решили свою проблему с Thomas & Betts RZ-NA 441-OMS, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Thomas & Betts RZ-NA 441-OMS со всей вероятностью он захочет поделиться методом ее решения.

Перепишите текст с картинки

Комментарии (0)