-
RIDGID R3120 - page 1
This new jig saw has been engineered and manufactured to our high standards for dependability, ease of operation, and operator safety. When properly cared for, the jig saw will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this produc ...
-
RIDGID R3120 - page 2
2 T ABLE OF CONTENTS ■ General Safety Rules ............................................................................................................................................ 3-4 ■ Specific Safety Rules .......................................................................................................... .......................... ...
-
RIDGID R3120 - page 3
3 GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SA VE THESE INSTRUCTIONS W ork Area ■ Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. ■ Do not operate power tools in ...
-
RIDGID R3120 - page 4
4 SPECIFIC SAFETY RULES ■ Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator. Additional Safety Rules ■ Know your power tool. Read operator ’ s manual caref ...
-
RIDGID R3120 - page 5
5 Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power min Minutes Time Alterna ...
-
RIDGID R3120 - page 6
6 SPECIFICA TIONS Input .................................................................................................................. 120 V olt s, 60 Hz, AC Only , 6.0 amperes No load speed .................................................................................................................. ...................... 1,000-3,000/min. ...
-
RIDGID R3120 - page 7
7 UNP ACKING INSTRUCTIONS This tool has been shipped completely assembled except for the blade. ■ Carefully remove the tool and accessories from the box. ■ Make sure that all items listed in the packing list are included. ■ Inspect the tool carefullshy to make sure no break- age or damage occurred during shipping. ■ Do not discard the packi ...
-
RIDGID R3120 - page 8
8 Fig. 1 Before using the orbital jig saw, familiarize yourself with all operating features and safety requirements. However, do not let familiarity with the tool make you careless. WARNING: Exercise caution when using this tool. Careless actions, for even a fraction of a second, can result in serious personal injury. Your new orbital saw is equipp ...
-
RIDGID R3120 - page 9
9 ASSEMBLY W ARNING: The tool should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the tool is not in use. Disconnecting the tool will prevent accidental starting that could cause serious injury . This saw has been shipped completely assembled except for the blade. ...
-
RIDGID R3120 - page 10
10 OPERA TION Fig. 3 SWITCH LOCK-ON BUTTON WARNING: The tool should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the tool is not in use. Disconnecting the tool will prevent accidental starting that could cause serious injury. W ARNING: Always wear eye protection ma ...
-
RIDGID R3120 - page 11
11 Fig. 5 OPERA TION Splinter-Free Cutting See Figure 4. This saw has a splinter guard to permit splinter-free cut- ting. It is especially useful when cutting plywood. This feature should only be used when making straight cuts or circle cuts. It is not for bevel cutting or plunge cutting. Note: The non-orbital setting also helps reduce splinter- in ...
-
RIDGID R3120 - page 12
12 OPERA TION Fig. 6 Hex Key Storage Insert hex key into storage area when not in use. It is located on the right front of your saw as shown in figure 6. W ARNING: Do not insert saw blade or hex key into air vents. They could come in contact with electrically live internal parts, and cause electrical shock result- ing in serious injury. W ARNING: T ...
-
RIDGID R3120 - page 13
13 OPERA TION Fig. 9 Fig. 8 WARNING: To avoid possible serious injury, keep hands and fingers from between the gear housing and saw blade clamp, and keep the chip shield in place. WARNING: Excessive side pressure to the blade could result in broken blades or damage to the material being cut. Orbital Motion See Figure 8. The blade of the saw cuts in ...
-
RIDGID R3120 - page 14
14 Angle Cutting (Bevel Cutting) See Figures 11 and 12. Bevel cutting angles may be adjusted from 0 ° to 45 ° right or left. Angles for cuts from 0 ° to 45 ° in 15 ° increments are marked on a scale on both the left and right side of the base. Notches on the rear of the base provide positive stops at each of the above mentioned 15 ° increment ...
-
RIDGID R3120 - page 15
15 OPERA TION Plunge Cutting See Figure 13, 14 and 15. W ARNING: To avoid loss of control, broken blades, or dam- age to the material being cut, always use extreme caution when making plunge cuts. We do not recommend plunge cutting on materials other than wood. To Make A Plunge Cut ■ Mark the line of cut clearly on the workpiece. ■ Set the orbi ...
-
RIDGID R3120 - page 16
OPERA TION Dustless Feature See Figure 16. For dustless operation, a vacuum attachment has been provided with the saw. It attaches to the saw base. WARNING: The jig saw should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the tool is not in use. Disconnecting the to ...
-
RIDGID R3120 - page 17
MAINTENANCE W ARNING: When servicing use only identical RIDGID® re- placement parts. Use of any other parts may cre- ate a hazard or cause product damage. W ARNING: The tool should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the tool is not in use. Disconnecting ...
-
RIDGID R3120 - page 18
NOTES 18 ...
-
RIDGID R3120 - page 19
19 This product is manufactured under license from Ridgid, Inc. by One World Technologies, Inc. All warranty communications should be directed to One World Technologies, Inc. at (toll-free) 1-866-539-1710. 90-DAY SATISFACTION GUARANTEE POLICY During the first 90 days after the date of purchase, if you are dissatisfied with the performance of this R ...
-
RIDGID R3120 - page 20
OPERA T OR'S MANUAL Orbital Jig Saw R3120 V ariable Speed Customer Service Information For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information when you call or visit. For the location of the authorized service center nearest you, please call 1-866-539-1710 or visit us online at w ...
У вас вопрос, касающийся RIDGID R3120?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с RIDGID R3120, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с RIDGID R3120 со всей вероятностью он захочет поделиться методом ее решения.