-
Pelco is110 - page 1
INST ALLA TION C3426M-E (3/09) IS110 Series Camclosure ® Integrated Camera System ...
-
Pelco is110 - page 2
...
-
Pelco is110 - page 3
C3426M-E (3/09) 3 Contents Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 ...
-
Pelco is110 - page 4
4 C3426M-E (3/09) List of Illustrations 1 Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 1 Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2 Basic Surfac e ...
-
Pelco is110 - page 5
C3426M-E (3/09) 5 Regulatory Notices This device complies with Part 15 of the FCC Rules. O peration is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE Th ...
-
Pelco is110 - page 6
6 C3426M-E (3/09) Description The IS110 Series Camclosure ® integrated camera system combines an environmental cover , back box, camera, lens, and lower dome into a small, high-securi ty system that is quick and easy to install. The system is perfect for a variety of indoor and outdoor applications and its versatile design allows for multiple moun ...
-
Pelco is110 - page 7
C3426M-E (3/09) 7 The IS111 models include the follow ing specifications: Indoor/outdoor dome , vandal resistant, surface mount, clear bubble, liner , and gray finish. PARTS LIST T able B. IS111, Clear Bubble with Liner Camera T ype Lens/Iris NTSC P AL Color , Wide Dynamic Range, Day/Night 3.0 to 9.5 mm, Day/Night V arifocal, Auto Iris IS111-DWV9 ? ...
-
Pelco is110 - page 8
8 C3426M-E (3/09) Figure 1. Package Components C OVER AND BA C K BOX 1 EA. C AMERA MODULE 1 EA. TRIM RING, LINER, AND C LEAR BUBBLE 1 EA. TRIM RING AND S MOKED BUBBLE 1 EA. < OR > 1/8-IN C H HOLLOW SC REWDRIVER BIT 1 EA. BLA C K PLUG 1 EA. S HOWN A C TUAL S IZE S HIPPING BOX 8-32 X 0.75-IN C H PHILLIP S P AN HEAD SC REW S 2 EA. 8-32 X 0.375-I ...
-
Pelco is110 - page 9
C3426M-E (3/09) 9 Cover and Back Box Installation The IS110 Series Camclosure integrated camera system mounts only to a surface. It can be wired through the cover into a surface, electrical box, or plaster ring. Y ou can also wire it through a side conduit. UNSHIELDED T WISTED PAIR V IDEO The IS110 Series offers support fo r unshielded twisted pair ...
-
Pelco is110 - page 10
10 C3426M-E (3/09) 8. Reinstall the back box inside the cover . For vandal-resistant installations, rotate the back box to position the conduit plug opposite the notch on the side of the cover . Use the two 8-32 x 0.375-inch Phillips pan head screws and washers (removed earlier) to secure the back box to the cover . Figure 2 . Basic Surfa ce Instal ...
-
Pelco is110 - page 11
C3426M-E (3/09) 11 6. Connect the power wires (refer to T able D). AC operation only: If you are wiring more than one Camclosure to the same transformer , connect one side of the transformer to the red wire on all uni ts; connect the other side of the transformer to the black wire on all units. NOTE: Failure to connect all AC powered units in th e ...
-
Pelco is110 - page 12
12 C3426M-E (3/09) 404 PLASTER RING INSTALLATION NOTE: Y o u should install the camera module into the back box before installing the back box into the cover . When installing the b ack box into the cover , rotate the camera mo dule to access the mountin g holes (refer to Camera Module on page 16 for more information). 1. Remove the two 8-32 x 0.37 ...
-
Pelco is110 - page 13
C3426M-E (3/09) 13 6. Reinstall the back box inside the cover . For vandal-resistant installations, rotate the back box to position the conduit plug opposite the notch on the side of the cover . Use the two 8-32 x 0.375-inch Phillips pan head screws and washers (removed earlier) to secure the back box to the cover . Figure 4. 404 Plaster Ring Insta ...
-
Pelco is110 - page 14
14 C3426M-E (3/09) SIDE CONDUIT INSTALLATION NOTE: Y o u should install the camera module into the back box before installing the back box into the cover . When installing the b ack box into the cover , rotate the camera mo dule to access the mountin g holes (refer to Camera Module on page 16 for more information). 1. Remove the two 8-32 x 0.375-in ...
-
Pelco is110 - page 15
C3426M-E (3/09) 15 8. Connect the video cable and wires: • BNC: Connect the BNC connector from th e unit to a ma ting BNC connector . • UTP: Connect the blue wire to Video +; connect the gray wire to V ideo -. 9. Connect the power wires (refer to T able F). AC operation only: If you are wiring more than one Camclosure to the same transformer , ...
-
Pelco is110 - page 16
16 C3426M-E (3/09) Camera Module The IS110 Series Camclosure camera modu le includes the camera, came ra bracket, and heate r board. T o perform most camera adjustments, you must remove the module from the back box. Use the following instructions to re move and reinstall the camera module. MODULE REMOVAL T o remove the camera module from the back b ...
-
Pelco is110 - page 17
C3426M-E (3/09) 17 2. Unplug the camera (10-pin), service (3-pin), and heater board (4-pin) connectors from the back box (refer to Figure 7). Figure 7. Back Box Connectors C AMERA C ONNE C TOR HEA TER BOARD C ONNE C TOR S ERVI C E C ONNE C TOR ...
-
Pelco is110 - page 18
18 C3426M-E (3/09) CAMERA ORIENTATION At the factory , the camera module is configured for ceiling mounting. For wall mou nting, you must change the camera orientation or the video image could be upside down or sideways. T o change the camera orientation (refer to Figure 8): 1. Remove the camera module from the back box, if necessary . 2. Remove th ...
-
Pelco is110 - page 19
C3426M-E (3/09) 19 Camera Adjustments T o perform the following camera adjustments, make su re to connect the camera and service connectors. Y ou may have to remove the camera module from th e back box. Connect a monitor . Then turn on power to th e camera and monitor . T o use the service connector , r efer to Service Connector on page 31. T o set ...
-
Pelco is110 - page 20
20 C3426M-E (3/09) T o adjust the fo cus: 1. Loosen the focus locking screw . 2. Position the inverted dome approximately 0.125 inch (3.175 mm) from the front of the lens. Make sure that the lens and the dome are cen tered (refer to Figure 10). 3. T urn the focus locking screw clockwise or counterclockwise to adjust the focus. 4. When the optimal f ...
-
Pelco is110 - page 21
C3426M-E (3/09) 21 DN/CH SERIES ADJUSTMENTS Refer to Figure 11 to adjust the IS110-DN or IS110-CH model. Figure 11. Adjusting the IS110-DN/C H Series Camclosure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW4-1: Auto Gain Control The auto gain control (AGC) adjusts the image automatically to compensate for ch ...
-
Pelco is110 - page 22
22 C3426M-E (3/09) SW4-4: Flickerless In certain lighting conditions, a flicker in the light source may affect camera operation. Flic kering can be caused by a number of conditions, including the qua lity of the source power and the age and type of fluorescent bulbs and ballasts. Set SW4-4 to ON to enable flickerless operation. The ca mera will rem ...
-
Pelco is110 - page 23
C3426M-E (3/09) 23 V ERTICAL PHASE ADJUSTMENT Use this procedure for 24 V AC ope ration only . When using more than one camera power supply, a brief vertical roll may occur on the monitor when switching from one came ra to another . T o eliminate vert ical roll, reverse the 24 VAC connec tions on one camera. If both cameras are connected to the sam ...
-
Pelco is110 - page 24
24 C3426M-E (3/09) DAY/NIGHT OPERATION NOTE: This section only applies to DN model cameras. DN model cameras regularly check the brightness level of the field of view t o determine when to switch between day (color) and nig ht (black-white) operation. Actual brightness threshold levels are affected by camera angle, amount of zoom, field of view , l ...
-
Pelco is110 - page 25
C3426M-E (3/09) 25 DW/CW SERIES (WIDE DYNAMIC RANGE) ADJUSTMENTS Refer to Figure 13 to adjust the IS110-DW or IS110-CW model. Figure 13. Adjusting the IS110-DW/C W Series Camclosure SWITCH SETTINGS Locate the DIP switch. Then set the switches for your installation. SW1-1: Video Format Set SW1-1 to ON for NTSC. Set it to OFF for P AL. The default se ...
-
Pelco is110 - page 26
26 C3426M-E (3/09) SW1-4: Auto White Balan ce/Manual White Bala nce Auto white balance (AWB) is enabled by default (ON). T o manually set and lock the white balance: 1. Set SW1-4 to ON. 2. Hold a white background in front of the lens until the video shows all white. 3. While holding the background in place, set SW1-4 to OFF . A green block and a wh ...
-
Pelco is110 - page 27
C3426M-E (3/09) 27 SW1-8: Day/Night Operation (DW models only) NOTE: On CW models, SW1-8 is unused and does not affect camera operation. DW model cameras regularly check the brightness level of the field of view to determine when to switch between day (color) and nig ht (black-white) operation. Use SW1-8 to set the general light levels at which the ...
-
Pelco is110 - page 28
28 C3426M-E (3/09) AUTO IRIS LEVEL ADJUSTMENT The electronics of the IS110-DW and IS110-CW Series Camclosures automatically adjust the camera to the auto iris. Auto iris level adjustments are n ot necessary . V ERTICAL PHASE ADJUSTMENT Use this procedure for 24 V AC ope ration only . When using more than one camera power supply, a brief vertical ro ...
-
Pelco is110 - page 29
C3426M-E (3/09) 29 Camera Positioning Rotate and tilt the camera module to position the camera. Then tighten the tilt screws (axis in Figure 15). NOTE: Do not over -rotate the module. Excessively turni ng the module in one direction could result in damage to the wiring. Figure 15. Positioning the Camera T ilt 80° (20° to 100°) Pan 36 ...
-
Pelco is110 - page 30
30 C3426M-E (3/09) Install Liner and T rim Ring 1. Adjust the liner (if installed), refer to Figure 16: a. Align the screw holes in the trim ring with those in the back box to identify the proper liner position. b. Loosen the three Phillips screws located in t he trim ring. c. Insert the blade of a standard screwdriver in one of the adjustment groo ...
-
Pelco is110 - page 31
C3426M-E (3/09) 31 Service Connector The IS110 Series Camclosure integrated camera system includes a service connector that outputs camera video. Use it at the installation site to se t up the field of view and to focus the camera. Figure 17. Service Connector Pelco offers two optional items that plug directly in to the service connector . Before u ...
-
Pelco is110 - page 32
32 C3426M-E (3/09) T o assemble the cable: 1. Attach the CPM 88 miniature coaxial connector to one end of the cable. Follo w the directions supplied with the mini ature coaxial connector . 2. Attach the 2.5 mm monaural plug to the other end of the coaxial cable (refer to Figure 18): a. Remove the support sleeve from the plug. b. Slip the support sl ...
-
Pelco is110 - page 33
C3426M-E (3/09) 33 Specifications GENERAL Pan/ T ilt Adjustment Manual Pan 360° T ilt 80° (20° to 100° range) Rotation 360° Construction Aluminum with steel camera mounting bracket and polycarb onate dome Impact IS110 is a rugged product t hat exceeds an IK10++ rating of Standard EN62262 and can withstand up to 100J in a vertical impact Cable ...
-
Pelco is110 - page 34
34 C3426M-E (3/09) CAMERA/LENS If you need technical specifications for the camera itself, refer to the IS110 specification online at www .pelco.com. (Design and product specifications subject to change without notice.) 1.797 (4.56) 3.593 (9.13) Ø 0.343 NOTE: V ALUE S IN P ARENTHE S E S ARE C ENTIMETER S ; ALL OTHER S ARE IN IN C HE S . 5.50 (13.9 ...
-
Pelco is110 - page 35
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merc handise pr oved defective in mate rial or work manship for a period of one year after the date of shipment. Exception s to this warrant y are as noted bel ow: • Five years: – Fiber optic products – TW3000 Series un shielded twiste d pair (U ...
-
Pelco is110 - page 36
Pelco, Inc. W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el (800) 289-9100 Fax (800) 289-9150 International T el +1 (559) 292-1981 Fax +1 (559) 348-1120 w w w .pel co.com ...
У вас вопрос, касающийся Pelco is110?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Pelco is110, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Pelco is110 со всей вероятностью он захочет поделиться методом ее решения.