-
Pelco BB08 - page 1
BB08 Series Inter cept ® Back Box Installation/ Operation Manual C456M-D (1/98) Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120 ® ...
-
Pelco BB08 - page 2
2 Pelco Manual C456M-D (1/98) CONTENTS Section Page 1.0 GENERAL .................................................................................................. 3 1.1 IMPORT ANT SAFEGU ARDS AND W ARNINGS ............................... 3 1.2 UNP A CKING INSTR UCTIONS .......................................................... 4 1.3 RECOMMENDED T O ...
-
Pelco BB08 - page 3
Pelco Manual C456M-D (1/98) 3 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORT ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following W ARNINGS should be obser v ed. 1. Installation and servicing should only be done by Qualified ...
-
Pelco BB08 - page 4
4 Pelco Manual C456M-D (1/98) 1.2 UNP ACKING INSTRUCTIONS Unpack and inspect all parts carefully . Be sure to sav e the shipping carton and any inser ts. They are the saf est mater ial in which to make future shipments. If an item appears to hav e been damaged in shipment, replace it proper ly in its carton and contact the factory at 1-800-289-9100 ...
-
Pelco BB08 - page 5
Pelco Manual C456M-D (1/98) 5 2.0 DESCRIPTION The BB08 Series of back bo xes is part of the IDS08 Intercept ® Series of domes. The IDS08 Series is an integral system that includes a back bo x (BB08), dome drive (DD08), dome receiv er/driver (DRD08), and imager/optics package (IOP08). This manual cov ers the BB08 Ser ies of back bo xes. For install ...
-
Pelco BB08 - page 6
6 Pelco Manual C456M-D (1/98) 3.0 INST ALLA TION 3.1 SUSPENDED CEILING 1. Remov e the ceiling tile from the ceiling. If you are installing the back bo x into a 2' x 4' (61 x 122 cm) ceiling grid, cut the tile in half and install an additional “T” bar for support. Reinstall one of the 2' x 2' (61 x 61 cm) sections. 2. Bring t ...
-
Pelco BB08 - page 7
Pelco Manual C456M-D (1/98) 7 T able A. Video Coaxial Cable Requirements Cable T ype* Maximum Distance RG59/U 750 ft (229 m) RG6/U 1,000 ft (305 m) RG11/U 1,500 ft (457 m) * Minimum cable requirements: 75 ohms All-copper center conductor All-copper braided shield with 95% braid co ver age Wire Gauge Maximum distance from transformer to load T able ...
-
Pelco BB08 - page 8
8 Pelco Manual C456M-D (1/98) 3. T o create an opening for the wiring, use a hammer and punch to remov e one of the knock outs in the top of the back bo x. If it is necessar y to work inside the back bo x, remov e the tr im ring and dome by inserting a screwdriver or your fingers between the trim ring and the faceplate and popping the trim ring and ...
-
Pelco BB08 - page 9
Pelco Manual C456M-D (1/98) 9 Figure 2. 24 V AC Bac k Box Wiring Diagram ...
-
Pelco BB08 - page 10
10 Pelco Manual C456M-D (1/98) Figure 3. 120 V AC Bac k Bo x Wir ing Diagram ...
-
Pelco BB08 - page 11
Pelco Manual C456M-D (1/98) 11 12. If you are not using Coaxitron ® control, connect the control wiring to RXD+ and RXD-. F rom controller T o 4-wire terminal inside back bo x TXD+ RXD+ TXD- RXD- 13. Back bo x installation is now complete . Proceed with the installation of the dome drive unit. Refer to the manual pro vided with the dome drive f or ...
-
Pelco BB08 - page 12
12 Pelco Manual C456M-D (1/98) 13. If you are not using Coaxitron ® control, connect the control wiring to RXD+ and RXD-. F rom controller T o 4-wire terminal inside back box TXD+ RXD+ TXD- RXD- 14. The bezel and dome assemb ly can be attached to the back bo x at this time, or it can be done after the dome drive is installed. T o install the dome ...
-
Pelco BB08 - page 13
Pelco Manual C456M-D (1/98) 13 Figure 4. BB08A120 Back Bo x Exploded Assembly Diagram 4.0 EXPLODED ASSEMBL Y DIAGRAMS E F A B 4 C D 6 2 3 5 7 8 1 ...
-
Pelco BB08 - page 14
14 Pelco Manual C456M-D (1/98) Figure 5. BB08E120 and BB08E211 Bac k Bo x es Exploded Assembly Diag ram ...
-
Pelco BB08 - page 15
Pelco Manual C456M-D (1/98) 15 T able C. BB08A120 Back Bo x Exploded Assembly P ar ts List (Figure 4) Item Quantity Description Part Number 1 1 T rim ring, white 8082ASSY 1 Dome seal (not shown) 80810007 1 Fixed dome, smoked (not shown) 80810008-4 1 Sound quieting ring (not shown) 8083001 2 1 Back box 8084297COMP 3 1 Face plate, drop ceiling, white ...
-
Pelco BB08 - page 16
16 Pelco Manual C456M-D (1/98) Figure 6. Back Plate Exploded Assemb ly Diagram ...
-
Pelco BB08 - page 17
Pelco Manual C456M-D (1/98) 17 T able E. Back Plate Exploded Assembly P ar ts List Item Quantity Description Part Number 1 2 Latch backup plate 8004244COMP 2 2 Latch 8004105COMP 3 2 Latch bracket 8004143COMP 4 1 T ransformer (120 V A C model only) TRF21243.30.70F 5 1 25-position connector plug CON10P025Z41T 6 2 Screw , 6-32 ZH208211-4 7 1 10-positi ...
-
Pelco BB08 - page 18
18 Pelco Manual C456M-D (1/98) 5.0 SPECIFICA TIONS ELECTRICAL Enclosure Back Box Input Voltage: 24 VAC or 120 VAC Power Requirements Receiver/Driver: 48 vA for 24 VAC and 120 VAC dome drives Blower (continuous duty): One (1) at 33 cfm, 6.7 watts, 120 VAC @ 60 Hz Heaters 120 VAC: 135 watts total Thermostatically controlled; activates ON at 40 ° F ( ...
-
Pelco BB08 - page 19
Pelco Manual C456M-D (1/98) 19 Figure 7. BB08A120 Dimension Drawings Figure 8. BB08E120 and BB08E211 Dimension Dra wing NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES ...
-
Pelco BB08 - page 20
20 Pelco Manual C456M-D (1/98) 6.0 WARRANTY AND RETURN INFORMA TION Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco. Endura and ExSite are trademarks of Pelco. © Copyright 1998, P elco . All rights reserved. WARRANTY Pelco will repair or replace, without charge, any merchandise proved defect ...
У вас вопрос, касающийся Pelco BB08?
Воспользуйтесь формуляром, находящимся ниже
Если с помощью найденной инструкции Вы не решили свою проблему с Pelco BB08, задайте вопрос, заполнив следующий формуляр. Если у какого то из пользователей была похожая проблема с Pelco BB08 со всей вероятностью он захочет поделиться методом ее решения.